Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Jacketed beaker for evaporation?
I was wondering if I could push steam of water, acetone or some other media through a jacketed beaker in order to evaporate/dry substances that are
not to be overheated? What material of tubing could resist acetone vapors? PTFE tubes tend to be very rigid.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3635
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
google "drying pistol"
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I'm aware of that device, but these beakers are more readily and cheaper available to me and could also have a dual use as temp controlled reaction
vessels.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3635
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
sorry, I just meant that you could maybe use the same principle,
a reflux condenser and suitable b.p. liquid with your jacketed beaker .. recycling the liquid.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Or you could just use a temperature controlled oil bath.
PID controllers are cheap and can be rigged to off the shelf hot plates from walmart.
That is half of what a rotovap is.
The other half being the rotating joint and motor.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Sulaiman,
I got that. My concept was actually just that of a drying pistol. I would practically distill the medium through the flask, and lead the lower port in
a return tube with reflux condenser for exhaust. The inlets for the flask are quite small for effective vapor transport and could cause significant
velocity increase, but considering the size of the vessel of 500mL or similar it shouldn't be an issue.
Bath is another idea, and temp control could actually come handy anyways. My induction plate has steps from 0 to 9, and with step 1 it already causes
1 liter of silicon oil to reach 120C and step 2 over 160C so it is extremely overpowered for such a small setup.
I'm currently using either oven, air drying or vacuum desiccator - or just as a desiccator until as soon as I get the vacuum leak fixed.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Using steam to warm a beaker or similar is nothing new, we did that to heat solutions when I was in college. Every lab had steam connections back
then. Now none do... I'm just really old.
But if you want to try jacketed beakers, I have some small ones, about 50 and 100 mls, I think. I used to use similar systems to keep buchner
funnels warm or additiono funnels cold. For many cases, just using a beaker ina water bath would also work, but is limited to 100C.
|
|