Pages:
1
2 |
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
A slightly dangerous but surprisingly effective way to make HCl
This setup uses a membrane chloroalkali cell which produces Cl2 and H2 and then is hooked up to a bubbler and sent to a quartz tube next to a UVC lamp
which produces HCl via these reactions.
HOCl + O3 = HCl + O2
H2 + Cl2 = HCl
The bubbler and the cell produces HOCl along with Cl2 also called wet chlorine.
Cl2 + H2O = HCl + HOCl
overall this process doesnt seem to happen explosively due to the existence of HOCl in the system but the gases produces can still ignite violently
and detonate so avoid any sources of ignition.
A future cell using mmo will have a PVC enclosure for the UVC lamp with input for gas and output for HCl liquid and vapor.
Video link below
https://youtu.be/SHX7EDW2hLw
![HCl gen.jpg - 59kB](https://www.sciencemadness.org/whisper/files.php?pid=644499&aid=83208)
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
Fuming HCl produced after 11 hours of runtime.
https://youtu.be/kMKDrHb4W7Q
|
|
metalresearcher
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 737
Registered: 7-9-2010
Member Is Offline
Mood: Reactive
|
|
What kind of membrane do you use ? Because a membrane is mandatory to prevent the OH- reacting with the Cl2 gas.
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
PVA + BORAX on synthetic cloth scaffhold
vid guide below
https://www.youtube.com/watch?v=dR7fW5J7njA
|
|
Syn the Sizer
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
I much prefer the safer OTC method of reacting sodium bisulfAte with NaCl products are sodium sulfate and HCl vapour. Of course this will also work
with H2SO4 with much better results. Though I just get muriatic acid from Canadian Tire for $15/4L
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
Heres my homemade HCl 24 hours runtime its already fuming like in the vid shown.
|
|
Syn the Sizer
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 591
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
Nice, well done.
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
after tweaking the cell a bit and messing with membranes and additives and current density to prolong the operating time I got 2 nice bottles of
fuming 12 molar HCl.
![HCl.jpg.png - 634kB](https://www.sciencemadness.org/whisper/files.php?pid=644772&aid=83290)
I got these by running the setup till HCl vapor was comming out of the 2nd hose in large amounts enough to turn the cumene test strip and pH paper a
nice red.
[Edited on 18-9-2020 by mysteriusbhoice]
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
Cost of production 82 Cents per liter of 37% HCl!!
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
What temperature did the pva membrane start failing at?
Was it the base material that failed or the pva started dissolving?
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
Quote: Originally posted by macckone ![](images/xpblue/lastpost.gif) | What temperature did the pva membrane start failing at?
Was it the base material that failed or the pva started dissolving? |
the failure conditions are still unknown because upon testing the membrane fails at temp 95 Celsius when slowly heated on a pot of water on the stove.
The membrane however fails in the cell if I let it run for too long but if I drain it after current reaches a certain value of 5 amps then it wont
fail and ive done 3 cycles so far and it didnt fail doing that.
The question is whether its current density that caused failiure or concentration gradient and hence now im running at lower voltage which means lower
current and if it still fails or fails before the previous value of current then it will be current density.
The PVA itself failed the base material remained if you used synthetic fabric.
The mode of failure seems to be that the PVA is getting disloged and ends up precipitating or floating around in the cathod chamber only!.
My guess is the current flow being too high caused the ions to migrate even the polymer but I cant say for sure.
addition of copper chloride prevents buildup of hypochlorites in anode chamber.
[Edited on 20-9-2020 by mysteriusbhoice]
|
|
Pumukli
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 696
Registered: 2-3-2014
Location: EU
Member Is Offline
Mood: No Mood
|
|
Nice to see this process working!
On the other hand, don't bee fooled by the apparent safety of the reaction! H2 and Cl2 does explode on illumination by a strong light source. (Visible
light suffice.) Been there, done that. Keep this in mind before making adjustments to your reactor! :-)
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
Quote: Originally posted by Pumukli ![](images/xpblue/lastpost.gif) | Nice to see this process working!
On the other hand, don't bee fooled by the apparent safety of the reaction! H2 and Cl2 does explode on illumination by a strong light source. (Visible
light suffice.) Been there, done that. Keep this in mind before making adjustments to your reactor! :-) |
I know that this can happen suddenly and hence theres now a shield ontop and a pool of water below.
I will even add a safety blow plug and hose in the final design for extra safety and it will be tested by detonation of gas inside.
The risk of this is with higher flow rate of input gas and yes the exit gases are still combustible but not explosive like the input gas when tested
in soapy water.
[Edited on 20-9-2020 by mysteriusbhoice]
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
The problem of failure of the PVA seems to be current density because after running it for really long continiously keeping the current below that
value at which it failed it got to a higher concentration and didnt fail completely.
The PVA in the cathode chamber seems to fail tho anyway but the anode chamber looks solid even at higher concentration gradient and since the anode
chamber membrane is still intact then I now calculated the current density of the membrane of the anode chamber at which it seems to fail and it looks
like its around above 58.4ma/cm^2.
my current operating current density is 51.66ma/cm^2
this is the borate membrane have to test the citrate and terephthalate membrane failure current density but the citrate seems to fail at higher
current density but its not easily repairable unlike borate so I will switch to that once care is taken to know the exact value at which it fails
probably once I get my variable current regulated power supply.
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
It sounds like there are three potential failure modes.
1) temperature gets too high (95C+)
2) sodium hydroxide concentration gets too high (commercial membranes fail at around 10%)
3) the current density is too high (58ma/cm^2)
A possible mechanism for the third failure mode is the mobilization of borate ions.
This would lead to depletion on the cathode side.
Since borate is responsible for the stability of the PVA film, its depletion would result in the film failing.
At some current density various nafion membranes fail as well.
So this is expected.
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
I have a new membrane that doesnt fail easily its Citrate crosslinked PVA and Terephthalate crosslinked PVA but if they fail these membranes are
harder to repair and unlike borate in which addition of borates into electrolyte mitigates 1 of those failures and borate membranes can be repaired in
30 seconds and used right away.
The NaOH definitely plays a role in fking up my membranes.
unless I can somehow think of a way to pump the NaOH out of solution and replace it or just increase the size of the cathode chamber so it can be run
on batch mode which is what I was thinking of in the final design.
The final design will be a 4 Liter cell like my chlorate one and the center will be anode and the 2 side compartments will be NaOH and membranes would
be PVA Citrate and using a current regulator buck converter set to a stable output at higher voltage I can essentially keep current constant and
calculate the run time based on when the cathode compartment gets to around 9.5% NaOH by wt.
[Edited on 20-9-2020 by mysteriusbhoice]
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Nice.
Could you, hypothetically, control the NaOH concentration by dripping in fresh solution from above and draining the used solution below?
|
|
papaya
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 615
Registered: 4-4-2013
Member Is Offline
Mood: reactive
|
|
Quote: Originally posted by mysteriusbhoice ![](images/xpblue/lastpost.gif) | I have a new membrane that doesnt fail easily its Citrate crosslinked PVA and Terephthalate crosslinked PVA but if they fail these membranes are
harder to repair and unlike borate in which addition of borates into electrolyte mitigates 1 of those failures and borate membranes can be repaired in
30 seconds and used right away.
The NaOH definitely plays a role in fking up my membranes.
unless I can somehow think of a way to pump the NaOH out of solution and replace it or just increase the size of the cathode chamber so it can be run
on batch mode which is what I was thinking of in the final design.
The final design will be a 4 Liter cell like my chlorate one and the center will be anode and the 2 side compartments will be NaOH and membranes would
be PVA Citrate and using a current regulator buck converter set to a stable output at higher voltage I can essentially keep current constant and
calculate the run time based on when the cathode compartment gets to around 9.5% NaOH by wt.
[Edited on 20-9-2020 by mysteriusbhoice] |
I want to ask you, have you ever tried the Na-CMC based membrane composition (which I proposed in other thread weeks ago), if yes - what are results ?
interesting to compare, since evidently you got very well versed in such things, good to know your opinion.
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
I havent found that ice pack containing CMC but I think it is sold on amazon so il try that when I can buy some but these times be rough for
international online shopping.
I will be trying Terephthalic acid-PVA membranes next which is easy for me to make now!
Just like the citrate it is probably also strong against acids but im hoping it also lasts longer.
|
|
papaya
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 615
Registered: 4-4-2013
Member Is Offline
Mood: reactive
|
|
Where I live it's sold as a wallpaper adhesive (dry form almost like sawdust), used in renovation etc. Very cheap stuff, can always be found in stores
where things like paint plaster etc is sold. But anyway, thanks for reply!
[Edited on 20-9-2020 by papaya]
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Na-CMC is going to be problematic outside of a solution that is closer to neutral.
Sodium Hydroxide is pretty aggressive towards cellulose.
Acids can degrade it as well.
Since it is modified cellulose it may hold up ok but I would not bet on it.
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
about removing NaOH from the reactor I can probably hook up a reservoir of water and a pump and also some aquarium tubes with a tap at the bottom
which can be opened after every few hours to replenish the electrolyte.
or I could also just do that manually but overall id rather not open the cell XD because obvious reasons usually the chlorine released while opening
is........ bad
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
You may want to use something a bit sturdier than aquarium tubing.
I tend to use HDPE ice maker tubing.
It is less flexible than the the clear pvc but it handles vacuum.
You could put a suction tube and an addition tube in through the lid.
Suction off the hydroxide and add water in measured amounts.
|
|
mysteriusbhoice
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 477
Registered: 27-1-2016
Member Is Offline
Mood: Became chemistry catboy Vtuber Nyaa
|
|
would aquarium pumps be fine handling the highly caustic NaOH solution though??
my other idea is to simply use the static head of the water by raising the cell and installing a bottom tap with a valve or plug.
btw borate membranes are pretty robust with boric acid additive in anode chamber which the acid form can crosslink PVA and hence stays in the anode
chamber dissolved.
I had one membrane run for 2 days with only a minor tear when it failed at the bottom due to mechanical stress when I manually drain the fluid in the
cathode side alone every cycle of dumping the contents of NaOH.
[Edited on 21-9-2020 by mysteriusbhoice]
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
You would probably be better served with a siphon type arrangement.
You can modify an aquarium pump to act as a vacuum.
The intermediate vessel can then be emptied without impacting the cell.
|
|
Pages:
1
2 |