Brightthermite
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 127
Registered: 26-6-2019
Member Is Offline
|
|
Distillation Ideas
I recently purchased a fractional distillation set up. It was purchased to purify and concentrate some sulfuric acid I have, but before I try that I
would like to become familiar with the set up and distillation. Any suggestions on useful and easy things to distill starting out while I get the hang
of it?
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Acetone, ethanol, toluene, anything you may need. I routinely recycle solvents by collecting them in separate bins and then distilling them pure in
boring days.
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Water, just water. Nothing flammable, nothing corrosive, just boring old water. Check the height of your head thermometer, make sure you read
100°C. If you've got a packed column see what it takes to flood it, not flood it. You better have some stirring because sulfuric bumps like crazy,
so check out the effect of stirring. Really get the hang of it. If you've got vacuum apply it, stop it, rinse and repeat. No sense messing with
anything potentially dangerous, just have fun with it. Count drips to determine the takeoff, increase and decrease temperatures. Take readings as if
it were your job.
|
|
TLutman
Harmless
Posts: 26
Registered: 13-10-2019
Member Is Offline
|
|
I’m curious what substance has a bp close enough to sulfuric acid to necessitate fractional distillation? I would worry about cracking glass with
the inevitable bumping, and I had issues with water flashing to steam, sending a huge vapor cloud that cleaned out the condenser several times. I
would think with the energy needed to reach the top of a column, you will experience similar
|
|
fdnjj6
Banned by request
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 114
Registered: 20-2-2019
Member Is Offline
Mood: Pissed
|
|
I tested my setup using a steam distillation of limonene. Nothing crazy. Especially using it for the first time you need to make sure everything works
and you don't want to end up like the guy I just read about on here who's brand new flask just decided to break for no reason even though he was doing
every single thing correctly and not abusing his glassware.
Once the water/steam distillation is done, move on to distilling things like ethanol and other useful solvents. Don't distill ether though. It's too
much of a fire/explosion hazard and many have been killed doing so. So stick to relatively tame stuff. I would discourage nitric acid distillation
until you really have things down and know what baths to use.
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
Plus one to what @BromicAcid said. It removes all variables and the hazards so you can focus on the process and the performance of your equipment..
|
|
Brightthermite
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 127
Registered: 26-6-2019
Member Is Offline
|
|
Thanks for the ideas. I am going to start with water as was suggested, once I practice and feel confident I will try a solvent. Besides distilled
water is useful
|
|
B(a)P
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
Put some food colouring or similar in your cooling water. In the event of spills or leaks it helps work out what is going on/what has gone where.
|
|
pneumatician
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 27-5-2013
Location: Magonia
Member Is Offline
Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **
|
|
Quote: Originally posted by Brightthermite ![](images/xpblue/lastpost.gif) | Thanks for the ideas. I am going to start with water as was suggested, once I practice and feel confident I will try a solvent. Besides distilled
water is useful |
be careful, if you distil 2 or 3 times tap water your flask get a white layer of fluorine or another shit and never get cristal clear again...
I "ruined" a expensive 10L reactor distilling tap water. now the glass have "cataracts". I read in a place a guy putting fluorine + nitric acids to
return to cristall clear but I lost this data or where I read it? wow too much surfing! :-)
|
|
zed
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Most likely Calcium and/or Magnesium Carbonates. Boil the flask out with vineger. Should clean it right up.
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
As zed said it's mg+ Calcium carbonates. Depending on where you are tap water will vary in concentration but it's definitely carbonates of some
mixture
One time I was doing the double boiler thing and little white spots start appearing on the pot and bottom of the bowl.upon tasting i found out what it
was: chalk. Stuff tasted exactly like chalk.
[Edited on 19-4-2021 by draculic acid69]
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I get those calcium cataracts all the time when I use water baths to heat many reactions. As the water slowly evaporates and I just add more, it
concentrates the calcium and other, which are less soluble in hot water, so they crystallize onto the bath kettle and to the flask. A quick rinse with
citric acid or vinegar will wipe them right off.
|
|
pneumatician
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 27-5-2013
Location: Magonia
Member Is Offline
Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **
|
|
obviously I rinse the flask with cheap household hcl but this only remove with fizing the carbonates in the surface ... but a bit every time,
acumulative penetrate in the glass and impossible to remove, no nitric, sulfuric... piranya with 3% H2O2...
look around the mouth, cristall clear, but the body...
|
|
pneumatician
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 27-5-2013
Location: Magonia
Member Is Offline
Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **
|
|
Quote: Originally posted by zed ![](images/xpblue/lastpost.gif) | Most likely Calcium and/or Magnesium Carbonates. Boil the flask out with vineger. Should clean it right up. |
I think I make a boiling with cheap hcl and no result... but maybe try again or with nitric + hydrofluoric and if not, leave it for distil water
alone.
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by pneumatician ![](images/xpblue/lastpost.gif) | obviously I rinse the flask with cheap household hcl but this only remove with fizing the carbonates in the surface ... but a bit every time,
acumulative penetrate in the glass and impossible to remove, no nitric, sulfuric... piranya with 3% H2O2...
look around the mouth, cristall clear, but the body... |
Maybe you got something other than just carbonates in your water.
|
|
pneumatician
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 27-5-2013
Location: Magonia
Member Is Offline
Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **
|
|
if not? :-)
|
|
zed
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
My local cafe owner usta clean out his Coffee pots with "Dutch Cleanser" and ice. Put a little cleanser inside the flask, with ice cubes, and swirl.
The mild abrasive action may clean things right up.
|
|
pneumatician
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 27-5-2013
Location: Magonia
Member Is Offline
Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **
|
|
Quote: Originally posted by zed ![](images/xpblue/lastpost.gif) | My local cafe owner usta clean out his Coffee pots with "Dutch Cleanser" and ice. Put a little cleanser inside the flask, with ice cubes, and swirl.
The mild abrasive action may clean things right up. |
this is a reactor with DN100, I can put my hand inside and the sticky shit is... well, part of the glass now? maybe with an electric polishing tool...
|
|
Keras
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 856
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
Quote: Originally posted by pneumatician ![](images/xpblue/lastpost.gif) |
this is a reactor with DN100, I can put my hand inside and the sticky shit is... well, part of the glass now? maybe with an electric polishing tool...
|
Try cerium oxide.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
If it's etched, there's little you can do. Just live with it, it won't affect anything but aesthetics. After all, auctions are full of glassware that
is literally covered in some sort of brown crap that is next to impossible to remove without boiling them in pure Caro's acid.
I like to keep my glassware spotless. I routinely clean them all by rinsing them with detergent and water(dishwashing soap, sodium percarbonate),
scrubbing if necessary and washing everything that fits in a dishwasher. Fritted filters I clean by first washing with acetone, then using sodium
hydroxide, and then citric acid, flushing with lots of water at all phases. Usually gets them shiny white, if not, I call in Mr. Piranha. In some
instances I just put the glass (no frit filters, as I broke one once by this way) in oven and burn off any residues.
Fast way to dry glassware, especially frits is to rinse with acetone and let evaporate. A bit slower is to cook water off in an oven, if one is at
hand.
|
|