Planophore
Harmless
Posts: 10
Registered: 8-7-2020
Member Is Offline
Mood: Red Alert
|
|
Failed Henry reaction with 3,4,5-TMB
I attempted a Henry reaction with 3,4,5-TMB using freebased phenethylamine as a catalyst, but after addition of plenty of water I didn't get any
precipitate (500ml total addded)
Here was my procedure
12.5g 3,4,5-TMB (63.7mmol) was stirred in 130ml GAA. Then 0.77g phenethylamine (6.37mmol) was added dropwise to the reaction mixture with constant
stirring along with 7.8g nitromethane (127.4mmol).
This mixture was then heated in a water bath maintained at 90 degrees Celsius for a bit over 1hr. During which the solution became gradually more
yellow.
This was then slowly diluted with 250ml distilled water after which no change occurred. So the mixture was transferred to a larger flask and again
250ml distilled water was added to no avail.
Any recommendations? thanks
|
|
|
njl
National Hazard
Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline
Mood: ambivalent
|
|
Why do you have so much GAA?
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Try it with out gaa.
|
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
No, some is needed at least, first its a good solvent for this reaction and second the acetate salt of the amine catalyst is much better working(with
ethylamine acetate I got for the same substrate 94% and was able to reproduce that too using the same conditions).
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Ok it just seems like a bit too much gaa was used
|
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Thats for sure, this could have easily sufficed when used with tenfold as much of the other reagents!
|
|
|
Planophore
Harmless
Posts: 10
Registered: 8-7-2020
Member Is Offline
Mood: Red Alert
|
|
Thanks a lot.
I’m currently re-running the reaction on a smaller scale with significantly less AcOH and the colour is looking a lot closer to the characteristic
yellow/orange of nitrostyrenes.
[Edited on 11-7-2020 by Planophore]
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Ammonium acetate is a perfectly good catalyst for this (giving 96% yields in my hands), there's no need to use phenylethylamine.
|
|
|
Planophore
Harmless
Posts: 10
Registered: 8-7-2020
Member Is Offline
Mood: Red Alert
|
|
My re-run was very successful and everything looks good. I think the issue was - as you have all said - far too much GAA (I also slightly adjusted the
quantity of amine). I appreciate your help
With regards to the ammonium acetate, I’ll give it a go if you’ve had such good yields with it. Do you mind telling me what molar equivalents you
used?
I mostly used the PEA because I had PEA HCl on hand and the freebasing step is quite fun (and it’s quite water soluble, which is good for the
workup)
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Here's the ammonium acetate procedure:
Aldehyde (25 mmol) and ammonium acetate (25 mmol, 1.93 g) were dissolved in nitromethane (6.8 mL, 7.7 g, 126 mmol) and acetic acid (15 mL). A few 3 Å
molecular sieves were added and the mixture was refluxed with stirring for 1 hr. After cooling to rt and removing molecular sieves, the mixture was
added to 13.8 g Na2CO3 suspended in 75 mL water. This mixture was extracted with ethyl acetate (2x20 mL). The combined extracts were dried (MgSO4) and
evaporated to yield the adduct as yellow needles (24.5 mmol).
|
|
|
Planophore
Harmless
Posts: 10
Registered: 8-7-2020
Member Is Offline
Mood: Red Alert
|
|
Appreciate it.
My yield of nitrostyrene with PEA was 74% (pre-recrystallisation), which is a bit disappointing
I’ll give it a go with ammonium acetate - was your 96% yield with TMB or another aldehyde?
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
