RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
Best solvent to remove & dissolve unfired rifle primers
I have a load of unfired 22lr cases that have been seperated, so it's just the brass case and the primer stuck to the case. I need to use the cases
as jackets for other rounds, so the primer needs to be removed, and there's about 2,000 of them, so I am thinking about doing it in smaller batches of
100-300 or so. I'd like to try to save the compound by recrystalizations and I'm wondering if using distilled water would be best or I also have
methanol, ethanol (75%), and some other standard solvents.
I've tried to figure out what the primer compound is, and it seems like it could be many different possibilities and it really comes down to the brand
and what they are using at the time (it can vary by year and batch...)
As a side note, I found some video's of people making their own primers from scratch, making the cups and anvil from flat stock and using an
assortment of compounds as the explosive from match heads to the powder from cap guns (even the paper tab caps were used as primers - that really blew
my mind that they were powerful enough to fire rifle or handgun ammo!)
This project came about b/c it was less expensive to use the components from the 22LR to make custom 5.56/223 rounds, at about 1/2 the cost, on top of
the 5.56 rounds not even being available in the near future. So the extracted primer and the powder are all bonus from the project.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
as you said, the composition varies a lot, so finding the one solvent that can dissolve all of them seems hard.
i found a generic composition, lead syphate, antimony sulfide and barium nitrate.
you could use hot water or methanol, but the sulfide won't dissolve
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
The way the .22LR is primed will make this a head act no matter what way you go, with that said, I'd try would be a water ethanol solution warmed in
an ultrasonic cleaner.
Dissolve the binder then vibrate out the rest, then evaporate as a batch, mix while still damp then store as such, remix befor using.
As for field expedient DIY primers they work, but naturally produces a less then ideal burn geometry inside the round, so you get wide spread in
muzzle velocity, and accuracy spread.
The art of priming you want a good focused jet of hot gasses to start the powder burning in a nice outward symmetrical pattern, you want a smooth
pressure curve as possible with a fast peak.
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
Quote: Originally posted by XeonTheMGPony ![](images/xpblue/lastpost.gif) | The way the .22LR is primed will make this a head act no matter what way you go, with that said, I'd try would be a water ethanol solution warmed in
an ultrasonic cleaner.
Dissolve the binder then vibrate out the rest, then evaporate as a batch, mix while still damp then store as such, remix befor using.
As for field expedient DIY primers they work, but naturally produces a less then ideal burn geometry inside the round, so you get wide spread in
muzzle velocity, and accuracy spread.
The art of priming you want a good focused jet of hot gasses to start the powder burning in a nice outward symmetrical pattern, you want a smooth
pressure curve as possible with a fast peak. |
The ultrasonic cleaner is a great idea, I wish I had one. I decided to try just using hot water, put it in a soda bottle and give a good shaking
every few mins. The water has turned a lime green and there is a fair amount of undissolved green powder. I'm actually kind of surprised at the
amount in each shell. I've never looked at how rimfire primers work and it looks like a ball of damp primer is dropped in and then it's pressed so it
is on the outer sides of the rim and up the side of the case about 4-6mm up the side.
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
yup or a mobile solution is dripped in and surface tension does the rest.
|
|