Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3027
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Dean Stark without Dean Stark.... almost quantitative
I tried to use a Dean Stark preparation to prepare the diketal of cyclopentanone with ethylene glycol. The first time I did this was with toluene.
This worked fine and I got a fine yield of 69%.
The second time I did it in xylene, this time I didn't get any water in the trap but I did get a very obvious water layer at the bottom of the flask.
Apparently water is so insoluble in xylene there is no need for a Dean Stark trap.
What I did was refluxing xylene with a bit of sulfuric acid (1 or 2 ml in 200 ml), which turned brown, and separate the acid from the xylene. This
xylene was used to prepare cyclopentanone ethylene diketal. A clear water layer formed after less than half an hour (about the amount calculated, 6
ml). The water layer was separated and after washing with brine and drying with magnesium sulfate the xylene was evaporated. A liquid with a boiling
temperature well above 150 degrees was isolated.
My best guess is that the liquid is the ketal of cyclopentanone. It is immiscible with water, so I think it can't be ethylene glycol. Neither can it
be cyclopentanone nor xylene as the boiling temperatures of those are lower. It weighs 50 grams, which would be a quantitative yield. I will do a
vacuum distillation on it after which I will determine the final yield.
Conclusion: there is no need for a Dean Stark trap; refluxing and separation of the water layer is sufficient when using xylene.
The xylene was obtained from thinner, simple distillation was preformed. The label says it contains xylene, acetone, isopropanol and isobutanol.
Everything boiling below 135 was disregarded. The boiling flask was clean after distilling; no residue.
[Edited on 22-2-2020 by Tsjerk]
|
|
Metacelsus
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2537
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Hmm, interesting. The benefit of a Dean-Stark trap is being able to continuously remove the water as the reaction proceeds, but I guess in this case a
simple phase separation performs the same role. I wonder if this can be applied to other reactions — if so, it would be useful to those of us who
don't have Dean-Stark traps.
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3027
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I'm pretty sure this can be applied to other reactions which ask for a Dean Stark. It should at least work for ketalizations with ethylene glycol of
ketones with a boiling point of at least 130 degrees. It should also work for ketones with a boiling point above 92 degrees, as the azeotrope of
xylene and water boils at that temperature.
Nowadays xylene is more OTC than toluene is.
Edit: the ketal should boil above the boiling temperature of xylene, of course... not the ketone. The reaction could be run at room temperature if
necessary. And even; the ketal could be distilled if boiling below xylene.
[Edited on 22-2-2020 by Tsjerk]
|
|
chemistry007
Harmless
Posts: 19
Registered: 14-6-2019
Member Is Offline
|
|
About dean start setup, one thing that i think can be interessting to try is add 3A molecular sieve.
In that way no need dean stark and all water is sucked by the sieve.
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3027
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
A problem with molecular sieves is that they don't handle acids well. Acids will dissolve they sieves. What you propose might work without an
acid, but it would take a decade.
In the case of ethylene there is also the problem of dehydration forming polyethylene glycol and I would also not trust sieves around any ketone for
that same reason.
[Edited on 3-3-2020 by Tsjerk]
|
|
chemistry007
Harmless
Posts: 19
Registered: 14-6-2019
Member Is Offline
|
|
SWIM using it with ketone...specially with methylamine.
But you are probably right, in acid condition it's not that usefull...but why you think it can take decade? As long as water is formed, it's sucked by
the seave...just have to have good stirring.
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3027
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
You don't have to "swim" here, better don't.
The reason you can use it for your condensation is because there is methylamine around, but one of your side products is a condensation product of the
ketone with itself, that is why you shouldn't dry for example acetone with sieves.
The reason why I think it would take a decade is because the reaction needs an acidic catalyst, without it either doesn't run or it takes ages.
|
|
chemrox
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
I tried anilation of a piperidone in xylene and the yields were less than disappointing ;^(
A well calibrated Dean Stark is a good way to monitor reax progress too. The apparatus is not expensive. I like to use it in conjunction with a
constant temperature control. I suppose sieves would work but there would be no way to observe the evolved water if the water is a measurement
parameter. Also sieves complicate the workup and add to the expense.
[Edited on 3-4-2020 by chemrox]
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|