Pages:
1
2 |
monolithic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Ill try the boiling water when I've got an empty flask. What's the knob with rst written on it for?
I'm thinking it means rheostat.but what's it there for if you can set the temperature with the number wheel thing?
[Edited on 30-10-2019 by draculic acid69] |
Quote: | V. Operation instruction
Place the equipment on level worktable, equip test-tube stand, and insert plug of sensor into sensor socket.
Put the container with liquid inside into the heating jacket, and dip the sensor into heating liquid.
Switch on the power accords with the machine, then the equipment screen will show the current temperature of heating liquid.
Press dial switch to set the temperature as heating needs.
Make sure the power line and the power socket are connected to heating jacket well; the.
When the displayed temperature reaches the setting point, the red indicator light will be lighten, then it gets into constant temperature state.
Adjust the RST knob to the left side, where is the smaller value position; wait until the temperature does not rise anymore, for example, when the
displayed temperature is lower than the setting temperature, then turn it to right side gradually. |
http://webcache.googleusercontent.com/search?q=cache:http://...
I have no idea what it does. Probably a classic case of shitty Chinese reverse engineering where they rip something off without understanding what the
fuck they're even doing.
|
|
G-Coupled
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
The RST is some sort of fine calibration setting maybe?
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
So no one knows what the rst knob actually does?once the display temp is lower than the setting temperature you adjust the knob to the right bcoz it
does what?
|
|
G-Coupled
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
Maybe it will allow you to calibrate the display temperature to match the setting temperature?
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Tried boiling a flask full of water.mantle still gets to 300~ish degrees'c even when dial is set to 100.it appears that the temperature probe isn't
more than 2 degrees off when it comes to boiling water.dont have a higher boiling liquid available ATM. Did figure out my glass thermometer is a lil
bit off.reads 108 in boiling water but the mantles 2-300'c spikes make it useless for anything other than boiling water.theres not one rxn I can do
that wouldn't be ruined by this kind of overheating.the knob doesn't seem to make a difference which ever way it's turned.this thing as it is is no
better than those 2000w hotplates from kmart.i might just rip the guts out and put a Pwm thyristor circuit in there like my other one which is working
fine.
|
|
monolithic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Tried boiling a flask full of water.mantle still gets to 300~ish degrees'c even when dial is set to 100.it appears that the temperature probe isn't
more than 2 degrees off when it comes to boiling water.dont have a higher boiling liquid available ATM. Did figure out my glass thermometer is a lil
bit off.reads 108 in boiling water but the mantles 2-300'c spikes make it useless for anything other than boiling water.theres not one rxn I can do
that wouldn't be ruined by this kind of overheating.the knob doesn't seem to make a difference which ever way it's turned.this thing as it is is no
better than those 2000w hotplates from kmart.i might just rip the guts out and put a Pwm thyristor circuit in there like my other one which is working
fine. |
Temperature controlled hot plates and mantles don't regulate the voltage to the heating element. It's expected that the mantle is going to hit 300 C
or whatever its maximum output is. Put the probe in a flask of water, completely ignore the temperature of the heating element, and set the
temperature of the mantle to something below boiling, like 70 C. Does it eventually stabilize at 70 C? Then it is working as it should. If the probe
is off by 8 C then I don't think there's much you can do as there doesn't seem a way to adjust the calibration. You can buy PID controllers pretty
cheap ($50 or less on Amazon or eBay) that offer a ton of configuration: support for different types of thermocouples/thermistors, support for K/F/C
units of temperature, calibration adjustment, etc. It wouldn't be much work to wire one up to an SSR or mechanical relay, to control a hot plate.
If you're looking for something to control the temperature output at the heating element, you need something like a soft heating mantle (Glas-Col or a
knockoff) plugged into an AC transformer (Variac or a knockoff), set atop a magnetic stirrer or magnetic hot plate/stirrer with the heating circuit
turned off.
[Edited on 11-2-2019 by monolithic]
|
|
G-Coupled
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
Yeah, it looks like maybe the best thing to do with these Won Hung Lo hotplates might be to just use the mechanical guts of them, rip out/bypass the
control circuitry and replace it with a working configuration of your own.
IME, the vast majority of heaters use a kind of PWM to regulate the heat. By that, I mean that they use full power 'pulses' of current of varying
lengths to the heating element to keep it within the desired temperature range.
IDK if it'd improve things a lot if a controller was used which allowed the current to the heating element to be continuously variable instead. I
guess it would remove the hysteresis that the 'full power PWM' heaters exhibit, where a 100C set temperature would result in the element would vary in
temperature from like 96-103C or whatever.
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by monolithic ![](images/xpblue/lastpost.gif) | Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Tried boiling a flask full of water.mantle still gets to 300~ish degrees'c even when dial is set to 100.it appears that the temperature probe isn't
more than 2 degrees off when it comes to boiling water.dont have a higher boiling liquid available ATM. Did figure out my glass thermometer is a lil
bit off.reads 108 in boiling water but the mantles 2-300'c spikes make it useless for anything other than boiling water.theres not one rxn I can do
that wouldn't be ruined by this kind of overheating.the knob doesn't seem to make a difference which ever way it's turned.this thing as it is is no
better than those 2000w hotplates from kmart.i might just rip the guts out and put a Pwm thyristor circuit in there like my other one which is working
fine. |
Temperature controlled hot plates and mantles don't regulate the voltage to the heating element. It's expected that the mantle is going to hit 300 C
or whatever its maximum output is. Put the probe in a flask of water, completely ignore the temperature of the heating element, and set the
temperature of the mantle to something below boiling, like 70 C. Does it eventually stabilize at 70 C? Then it is working as it should. If the probe
is off by 8 C then I don't think there's much you can do as there doesn't seem a way to adjust the calibration. You can buy PID controllers pretty
cheap ($50 or less on Amazon or eBay) that offer a ton of configuration: support for different types of thermocouples/thermistors, support for K/F/C
units of temperature, calibration adjustment, etc. It wouldn't be much work to wire one up to an SSR or mechanical relay, to control a hot plate.
If you're looking for something to control the temperature output at the heating element, you need something like a soft heating mantle (Glas-Col or a
knockoff) plugged into an AC transformer (Variac or a knockoff), set atop a magnetic stirrer or magnetic hot plate/stirrer with the heating circuit
turned off.
[Edited on 11-2-2019 by monolithic] |
Imagine your doing a 100ml size grignard and you set the temperature control to 60'c
and then within a minute it's boiling and then it's out of control spewing out of the flask bcoz this 'operating as it should' mantle heated up to
over 250'c within a minute
(gets hot quick) other than boiling water that kind of temperature difference has the potential to ruin rxn's.
[Edited on 2-11-2019 by draculic acid69]
|
|
monolithic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Imagine your doing a 100ml size grignard and you set the temperature control to 60'c
and then within a minute it's boiling and then it's out of control spewing out of the flask bcoz this 'operating as it should' mantle heated up to
over 250'c within a minute
(gets hot quick) other than boiling water that kind of temperature difference has the potential to ruin rxn's.
[Edited on 2-11-2019 by draculic acid69] |
You should use a soft mantle, AC transformer, and a magnetic stirrer for situations like that. Even a hot water bath on a magnetic stirrer/hot plate
would work well for something that has to run at 60 C, speaking from experience. Also, I doubt even your current setup would heat the reaction mixture
to 250 C within a minute. The heating element would hit 250 C within a minute but it takes time to transfer that heat through the glass and to the
reaction mixture.
|
|
SWIM
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
Okay, I probably missed something in this thread, but did you try adjusting with the RST knob as directed?
I'm not sure what it does either. But it seems to be something they definitely want you to do.
Maybe it calibrates the thermocouple.
Maybe it limits the current flow to the heating element.
Maybe its worth a try.
EDIT: Thanks for the information, G-coupled. (Below)
[Edited on 2-11-2019 by SWIM]
|
|
G-Coupled
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
They tried the RST knob, but it didn't appear to change anything.
I'd have a lookyloo inside and see where the RST knob is attached, and see if that might help figure out what it's supposed to do.
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Tried the knob didn't do much.its wired directly to the board.
|
|
G-Coupled
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
Yes, but attached to *what* - where do the traces go to from where it's attached? ![:cool:](./images/smilies/cool.gif)
Any chance of a photograph of all the gubbins inside?
[Edited on 3-11-2019 by G-Coupled]
|
|
Deathunter88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 514
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Quote: Originally posted by monolithic ![](images/xpblue/lastpost.gif) | Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Tried boiling a flask full of water.mantle still gets to 300~ish degrees'c even when dial is set to 100.it appears that the temperature probe isn't
more than 2 degrees off when it comes to boiling water.dont have a higher boiling liquid available ATM. Did figure out my glass thermometer is a lil
bit off.reads 108 in boiling water but the mantles 2-300'c spikes make it useless for anything other than boiling water.theres not one rxn I can do
that wouldn't be ruined by this kind of overheating.the knob doesn't seem to make a difference which ever way it's turned.this thing as it is is no
better than those 2000w hotplates from kmart.i might just rip the guts out and put a Pwm thyristor circuit in there like my other one which is working
fine. |
Temperature controlled hot plates and mantles don't regulate the voltage to the heating element. It's expected that the mantle is going to hit 300 C
or whatever its maximum output is. Put the probe in a flask of water, completely ignore the temperature of the heating element, and set the
temperature of the mantle to something below boiling, like 70 C. Does it eventually stabilize at 70 C? Then it is working as it should. If the probe
is off by 8 C then I don't think there's much you can do as there doesn't seem a way to adjust the calibration. You can buy PID controllers pretty
cheap ($50 or less on Amazon or eBay) that offer a ton of configuration: support for different types of thermocouples/thermistors, support for K/F/C
units of temperature, calibration adjustment, etc. It wouldn't be much work to wire one up to an SSR or mechanical relay, to control a hot plate.
If you're looking for something to control the temperature output at the heating element, you need something like a soft heating mantle (Glas-Col or a
knockoff) plugged into an AC transformer (Variac or a knockoff), set atop a magnetic stirrer or magnetic hot plate/stirrer with the heating circuit
turned off.
[Edited on 11-2-2019 by monolithic] |
Imagine your doing a 100ml size grignard and you set the temperature control to 60'c
and then within a minute it's boiling and then it's out of control spewing out of the flask bcoz this 'operating as it should' mantle heated up to
over 250'c within a minute
(gets hot quick) other than boiling water that kind of temperature difference has the potential to ruin rxn's.
[Edited on 2-11-2019 by draculic acid69] |
monolithic is right, you can't expect everything to work the way you think it should in your brain. A heating mantle designed the way you think it
should work would be useless, imagine wanting to boil some water and your mantle only heats to 100C. Your water is never going to boil.
Your "hypothetical" situation is like saying, this masonry drill doesn't work well when I try to use it for dentistry, it just destroyed my patient's
entire mouth. They should have finer speed control on it. It's not the problem with the equipment, but with the way you're using it.
|
|
G-Coupled
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
To be fair, until recently all kitchen microwaves worked like that until recently, using full power but with less duty cycles when the heat setting is
turned down, but a couple of years ago Panasonic brought out a new type of microwave which used actual true variable power to heat things.
[Edited on 3-11-2019 by G-Coupled]
|
|
wg48temp9
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 774
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
From reading the instructions the control knob varies the maximum heating power. Assuming it not faulty (stuck on full power) you should be able to
verify that by checking the max temperature of the mantle say at 0% 50% and 100% rotation of the knob while the temperature thumb switches are set at
max temperature or better yet check the power consumed with an in-lead power meter in place of measuring the mantle temperature.
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by Deathunter88 ![](images/xpblue/lastpost.gif) | Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Quote: Originally posted by monolithic ![](images/xpblue/lastpost.gif) | Quote: Originally posted by draculic acid69 ![](images/xpblue/lastpost.gif) | Tried boiling a flask full of water.mantle still gets to 300~ish degrees'c even when dial is set to 100.it appears that the temperature probe isn't
more than 2 degrees off when it comes to boiling water.dont have a higher boiling liquid available ATM. Did figure out my glass thermometer is a lil
bit off.reads 108 in boiling water but the mantles 2-300'c spikes make it useless for anything other than boiling water.theres not one rxn I can do
that wouldn't be ruined by this kind of overheating.the knob doesn't seem to make a difference which ever way it's turned.this thing as it is is no
better than those 2000w hotplates from kmart.i might just rip the guts out and put a Pwm thyristor circuit in there like my other one which is working
fine. |
Temperature controlled hot plates and mantles don't regulate the voltage to the heating element. It's expected that the mantle is going to hit 300 C
or whatever its maximum output is. Put the probe in a flask of water, completely ignore the temperature of the heating element, and set the
temperature of the mantle to something below boiling, like 70 C. Does it eventually stabilize at 70 C? Then it is working as it should. If the probe
is off by 8 C then I don't think there's much you can do as there doesn't seem a way to adjust the calibration. You can buy PID controllers pretty
cheap ($50 or less on Amazon or eBay) that offer a ton of configuration: support for different types of thermocouples/thermistors, support for K/F/C
units of temperature, calibration adjustment, etc. It wouldn't be much work to wire one up to an SSR or mechanical relay, to control a hot plate.
If you're looking for something to control the temperature output at the heating element, you need something like a soft heating mantle (Glas-Col or a
knockoff) plugged into an AC transformer (Variac or a knockoff), set atop a magnetic stirrer or magnetic hot plate/stirrer with the heating circuit
turned off.
[Edited on 11-2-2019 by monolithic] |
Imagine your doing a 100ml size grignard and you set the temperature control to 60'c
and then within a minute it's boiling and then it's out of control spewing out of the flask bcoz this 'operating as it should' mantle heated up to
over 250'c within a minute
(gets hot quick) other than boiling water that kind of temperature difference has the potential to ruin rxn's.
[Edited on 2-11-2019 by draculic acid69] |
monolithic is right, you can't expect everything to work the way you think it should in your brain. A heating mantle designed the way you think it
should work would be useless, imagine wanting to boil some water and your mantle only heats to 100C. Your water is never going to boil.
Your "hypothetical" situation is like saying, this masonry drill doesn't work well when I try to use it for dentistry, it just destroyed my patient's
entire mouth. They should have finer speed control on it. It's not the problem with the equipment, but with the way you're using it.
|
Not even close.i know how a usual mantle works it's just this one with a probe and setting the temperature using the dials is a lot different than
what I'm used to.its just something with this much of a temperature spike above the set temperature makes it no more useful than a $30
hotplate from Kmart. how often do you need to boil water in a flask that can't be done in a pot? I didn't buy it to boil water and I just can't trust
it to maintain set rxn temperature with the spiking up to 250'c+ all of a sudden even when it's sitting in the right temp range the way it did several
times.my thermometer only goes up to 250 so for all I know it could have hit 400'c and when your distillation or reflux is all clamped in its not like
I can just lower the mantle out of the way till it cools down and with the temperature spikes all the rxn's I'm doing would be ruined by that.as for
trying to trace where the temp probe goes on the board I can't really follow it.the 8 pins on the transformer confuse me.theres shit loads of
resistors though.25 of them.
|
|
Pages:
1
2 |