Smoker Root
Harmless
Posts: 35
Registered: 29-7-2019
Member Is Offline
|
|
Wich synthesis is better for HMTD
Hi, I alredy made this substance before with a friend a long time ago with a friend, I seriously can't remember the synthesis. It might be because of
my forgetfull memory I can't remember the synthesis. So I was searching for a reliable synthesis, so I found two that look promising. First one of
darian ballard. This guy made a lot of boomb boom and he has it on video, so I can actually trust him. The downside is that his lab techniques are
some times despicable, but of course that does not matter.
Link: https://m.facebook.com/stardustclub.madrid/events/?ref=page_...
Link:https://www.bitchute.com/video/cKXvFHp6whv6/
My other choice is the official sciencemadness synthesis. Which one should I choose. Or should adpat one of it?
Help please
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
what are you doing with it? that would be the first question as that is what determines what would be the best process.
|
|
Smoker Root
Harmless
Posts: 35
Registered: 29-7-2019
Member Is Offline
|
|
My idea is to explore the science and produce small amounts (1-2g would be enough, and 5g would be the maximun I would prepare) anyway I will just
scake down the procedures.
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
then really any method is good, try both acids out, try storing some un washed, some washed and compare the samples.
|
|
Smoker Root
Harmless
Posts: 35
Registered: 29-7-2019
Member Is Offline
|
|
Thanks! However I must ask, should I magnetically stirr? Since the only possible way to do it mechanically is with my hand and I think it is a lot of
time
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
just have to stir during mixing, once fully mixed set it some where cold and dark & out of the way and come back later.
Put it in a secondary bowl too, if some thing goes wrong the polymer is a pain to clean up.
If you have a microscope, generate some at room temp, then generate some at cold temps 4c to 0c, divide these batches into 2, wash one half, leave
the other unwashed then compare crystal structure and behaviors. work with very very small amounts for these experiments as spontaneous ignition risk
will be very high for the unwashed samples.
I have noted that after a year power levels became weaker, this was with carefully preped and washed HMTD.
FYI 150mg will set off base charge of ETN when pressed! I used 300mg to ensure, after one year this would start to have failures to detonate pressed
ETN
[Edited on 5-10-2019 by XeonTheMGPony]
|
|