| Pages:
1
..
10
11
12
13
14
..
16 |
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
Some possibilities come to mind:
1 - a seal to keep external air from entering the flask; you called this an airlock.
2 - a seal to allow gas(es) generated in the Erlenmeyer flask to escape, without external air entering; also preventing a build up of pressure in the
flask due to generated gas.
3 - allow gas generated in the flask to react with a reagent in the u-tube for identification purposes.
4 - as you said, to make things look more "science-y)!
|
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
Do you have links to the vid(s)?
|
|
|
SuperOxide
Hazard to Others
Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline
|
|
Quote: Originally posted by CharlieA  | Some possibilities come to mind:
1 - a seal to keep external air from entering the flask; you called this an airlock.
2 - a seal to allow gas(es) generated in the Erlenmeyer flask to escape, without external air entering; also preventing a build up of pressure in the
flask due to generated gas.
3 - allow gas generated in the flask to react with a reagent in the u-tube for identification purposes.
4 - as you said, to make things look more "science-y)!
|
Thanks for the reply, CharlieA. My replies to each point are below:
1 & 2 - The reason I decided this wasn't likely was because the size/shape/volume seemed to make it unlikely, as well as the fact
that the liquid inside of each instance of this apparatus being used was a different color (as if it was an indicator of some kind, not just regular
water in an air lock).
3 - This is definitely my leading assumption, but I'm curious as to what the name of this glass piece is called (since there are a
number of different glassware that can be used to accomplish this).
4 - This possibility is still on the table, the reason I'm not fully decided on it is because it seems to fit inline with what the
narrator is talking about (which is referenced in the links in my reply to fusso below).
================
Yep! Was able to find it again, thankfully. The specific Forensic Files episode is Penchant for Poison (S10E33)
After going through the relevant parts of the video again, I found out the technique they were using this glass apparatus for was called colorimetric testing.
The relevant parts of the video are listed below:
Here's when they talk about the chemical test they perform (@ 13:07)
Here's when you first get a glimpse at the actual glassware in question (@ 13:31)
And here's a bit of a closer look at one of them (@ 13:35)
Hope that helps, and thanks again!
P.S. This is my first post on the SM forums! (or I guess this specific post is my second, but you get what I mean). Long time lurker, finally grew
some balls and decided to make an account and get involved. So.. nice to [virtually] meet you guys!
|
|
|
yobbo II
National Hazard
Posts: 766
Registered: 28-3-2016
Member Is Offline
Mood: No Mood
|
|
Stopper with handle
Hi,
What is this item. It simply looks like a stopper with a handle. There is no access to the inside of the stopper and 'handle'.
Yob
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
Looks like the stoppers you see on some old Iodine flasks used in Iodine determination tests.
I have no idea why they look like that, but some of them do.
|
|
|
yobbo II
National Hazard
Posts: 766
Registered: 28-3-2016
Member Is Offline
Mood: No Mood
|
|
Perhaps it is to help stop your hands from getting contaminated or discoloured with product.
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
I think that this is just an "old-fashioned" glass stopper. Perhaps the "handle" was hand made by a glass blower. Out of curiosity, is the ground
stopper part a standard taper? I wouldn't think it is so old that it is a one-of-a-kind, but it would make a neat little display with other odd
glassware that we all tend to accumulate through the course of time!
A better way to protect your hands from iodine might be to wear gloves
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
https://www.camlab.co.uk/iodine-flasks-quickfit-p18359.aspx
I meant stoppers like these.
Yobbo II's stopper is 24/29 according to the markings.
[Edited on 9-11-2019 by SWIM]
[Edited on 9-11-2019 by SWIM]
|
|
|
Doc B
Hazard to Others
Posts: 107
Registered: 5-4-2012
Member Is Offline
Mood: No Mood
|
|
I have NFI what these are but I've somehow managed to accumulate a bunch of them.
 
Edit: the hook near the spout is actually a vent or something that opens to the outside. Does anyone have any idea what they are or what ould be used
for?
[Edited on 24-12-2019 by Doc B]
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
They look like a bartender could use them to measure out shots of hard liquor.
They are mighty familiar though. I'm SURE I've seen these on Ebay.
Maybe related to chromatography somerhow?
EDIT: looked on Ebay, the only similar thing I saw was obviously mis-named.
[Edited on 25-12-2019 by SWIM]
|
|
|
Doc B
Hazard to Others
Posts: 107
Registered: 5-4-2012
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by SWIM | They look like a bartender could use them to measure out shots of hard liquor.
They are mighty familiar though. I'm SURE I've seen these on Ebay.
Maybe related to chromatography somerhow?
EDIT: looked on Ebay, the only similar thing I saw was obviously mis-named.
[Edited on 25-12-2019 by SWIM] |
They could be for chromatographic use but I'm really not sure. What did you find on ebay?
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
I went looking for the mis-named posting (it was something totally inane, like lab beaker distillation flask), when I found this: https://www.ebay.com/itm/Amber-Glass-50-ml-Tilt-Measure-Disp...
So It's apparently a tilt measure dispenser.
You COULD set up a bar with these.
EDIT: Incidentally, I think I was confusing them with chromatography sprayers.
Another Item I know little about.
[Edited on 27-12-2019 by SWIM]
And these do seem to have a vent where your ones do, but it's just a little bump on these models.
[Edited on 27-12-2019 by SWIM]
|
|
|
Doc B
Hazard to Others
Posts: 107
Registered: 5-4-2012
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by SWIM | I went looking for the mis-named posting (it was something totally inane, like lab beaker distillation flask), when I found this: https://www.ebay.com/itm/Amber-Glass-50-ml-Tilt-Measure-Disp...
So It's apparently a tilt measure dispenser.
You COULD set up a bar with these.
EDIT: Incidentally, I think I was confusing them with chromatography sprayers.
Another Item I know little about.
[Edited on 27-12-2019 by SWIM]
And these do seem to have a vent where your ones do, but it's just a little bump on these models.
[Edited on 27-12-2019 by SWIM] |
Mystery solved. Thank you SWIM!
I will have to try them out and determine the volume delivered by the different sizes.
More mystery glass to come, stay tuned!
Although I'm pretty sure some of it was made just to fcuk with me.
|
|
|
Eddie Current
Hazard to Self
Posts: 78
Registered: 25-7-2018
Member Is Offline
|
|
| Quote: Originally posted by Sulaiman | Because I'm emigrating from UK I thought I'd 'stock up' on used Quickfit via eBay when suitable (cheap),
I just won this item that is described as 'Vintage Pyrex Separating Funnel Double Tap Laboratory Glassware'
but looks more like a gas sampling tube with 3-way valves.
Anyone know of a specific use for this configuration ?
|
It is a gas sample collection tube designed for vacuum and trapping.
|
|
|
ekilsawkcalbeoj
Harmless
Posts: 7
Registered: 26-6-2020
Location: NYC
Member Is Offline
Mood: Energized Blob
|
|
It's a receiving flask, but I'm not quite sure the purpose of the upper valve and side vent/cap. If it's for draining without breaking vacuum, I
suspect I should vent carefully before draining?
I tried searching forever on the internet to find something like it so I could see what it was called or how it operated, but could never find one
like it. 
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
How is the side vent finished?
I assume it's not a ground joint under there, so is it just like a rubber cap on a beaded tube or something else?
Beaded tubes I usually think of as for hoses.
Perhaps the vent goes to a hose to the vac pump to rapidly re-establish vacuum after draining the flask.
Since there's virtually no space for distillate to accumulate above the top valve (I'm assuming your condenser is a common style), it might be
important to evacuate that flask quickly so you can start collecting distillate instead of it just running back into the boiling flask.
This is a hypothesis based entirely on what I see here. I haven't seen anything like it on a rotovap before.
EDIT: But here is what looks like a similarly functioning
fitting:https://www.ebay.com/itm/USA-Lab-50L-Rotary-Evaporator-RotoVap-RE-1050-180-C-220V/401655360968?hash=item5d84866dc8:g:Zt0AAOSwIfFdufmN
The rotovaps I've looked at before were mostly ones I thought I might buy: cheap simple ones.
You've got a Ferrari and some of the parts just don't look like the ones on the Studebakers I've been looking at.
Okay, that picture didn't work, but this link should:
[Edited on 28-6-2020 by SWIM]
|
|
|
Eddie Current
Hazard to Self
Posts: 78
Registered: 25-7-2018
Member Is Offline
|
|
Has anyone encountered these things before?
50 mm in height x 15mm diameter. 19/26 joints.
  
I assume it's some type of sampler or instrument vessel.
[Edited on 28-6-2020 by Eddie Current]
|
|
|
ekilsawkcalbeoj
Harmless
Posts: 7
Registered: 26-6-2020
Location: NYC
Member Is Offline
Mood: Energized Blob
|
|
| Quote: Originally posted by SWIM | How is the side vent finished?
I assume it's not a ground joint under there, so is it just like a rubber cap on a beaded tube or something else?
Beaded tubes I usually think of as for hoses.
Perhaps the vent goes to a hose to the vac pump to rapidly re-establish vacuum after draining the flask.
Since there's virtually no space for distillate to accumulate above the top valve (I'm assuming your condenser is a common style), it might be
important to evacuate that flask quickly so you can start collecting distillate instead of it just running back into the boiling flask.
This is a hypothesis based entirely on what I see here. I haven't seen anything like it on a rotovap before.
EDIT: But here is what looks like a similarly functioning
fitting:https://www.ebay.com/itm/USA-Lab-50L-Rotary-Evaporator-RotoVap-RE-1050-180-C-220V/401655360968?hash=item5d84866dc8:g:Zt0AAOSwIfFdufmN
The rotovaps I've looked at before were mostly ones I thought I might buy: cheap simple ones.
You've got a Ferrari and some of the parts just don't look like the ones on the Studebakers I've been looking at.
Okay, that picture didn't work, but this link should:
[Edited on 28-6-2020 by SWIM] |
It's GL style glass threads similar to the GL14 barbs I have on the condenser, but much larger of an opening. The plastic I believe is PTFE. I think
it's just a vent though, like you'd close the stopcock on the top, twist the vent slowly to release vacuum, then drain the flask at the bottom. I
assume when drained, you'd slowly open the stopcock at the top and pull in a bunch of vapor from the condenser, which would probably be ok. But I'm
no expert, these are just assumptions.
You're right though, just a hypothesis, again I've never seen anything like this before. I would also compare it to one of the receiver flasks you
see on the industrial size rotavap's, but those often just have a drain and stopcock on the bottom, not the side vent and stopcock at the top. This
is what's confusing me.
If it helps, I'm pretty sure the rotavap this was attached to was used for some kind of cannabis processing. There was some resin stuck to the glass
when it arrived and the smell was kind of obvious. Also, the maker is Adams & Chittenden, and they only make custom glass to order, if you like unusual glassware, you should check out their gallery pages, there's
some really cool stuff in there. I should probably ask them if they remember making it.
|
|
|
Eddie Current
Hazard to Self
Posts: 78
Registered: 25-7-2018
Member Is Offline
|
|
| Quote: Originally posted by ekilsawkcalbeoj | | Also, the maker is Adams & Chittenden, and they only make custom glass to order, if you like unusual glassware, you should check out their gallery pages, there's
some really cool stuff in there. I should probably ask them if they remember making it. |
There's some amazing pieces in their collection.
A jacketed Vigreux is now on my "must get" list.
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
https://www.ebay.com/itm/133406852719
Doesn't look like distillation apparatus to me.
Something for mixing gasses maybe?
[Edited on 2-7-2020 by SWIM]
|
|
|
nzlostpass
Hazard to Self
Posts: 66
Registered: 3-9-2019
Member Is Offline
|
|
NOONE ELSE NOTICE.........
Noone else notice the two skiers about to descend the ski slope scene in this piece?
I honestly thought that's what you would be showing us at first!
| Quote: Originally posted by ekilsawkcalbeoj |
It's a receiving flask, but I'm not quite sure the purpose of the upper valve and side vent/cap. If it's for draining without breaking vacuum, I
suspect I should vent carefully before draining?
I tried searching forever on the internet to find something like it so I could see what it was called or how it operated, but could never find one
like it.
|
|
|
|
Junk_Enginerd
Hazard to Others
Posts: 251
Registered: 26-5-2019
Location: Sweden
Member Is Offline
|
|
Any ideas? Found it at a random yardsale for nothing. It's definitely borosilicate, so I assume it's a lab product.
|
|
|
Eddie Current
Hazard to Self
Posts: 78
Registered: 25-7-2018
Member Is Offline
|
|
It's a bit hard to tell from that image. My guess is that it's some type of atomiser.
|
|
|
The Plutonium Bunny
Harmless
Posts: 21
Registered: 22-4-2015
Location: On an actinide asteroid
Member Is Offline
Mood: Fissile
|
|
"Soxhlet Extractor"
Does anyone have an idea what this piece is? I recently acquired it in a box labelled "Soxhlet Extractor", but it is rather unlike any Soxhlet I have
seen before. There is no ground glass to be found on the whole thing. Additionally, one of the tubes is positioned such that it drips directly on the
glass frit inside the chamber; the frit leads to another tube exiting the chamber. A final tube leads directly into the glass chamber. There are no
obvious places for attaching a condenser of any kind.
It looks fancy (expensive), but I have no idea what useful purposes it might serve. Thank you for your help in its identification!
  
|
|
|
itsallgoodjames
Hazard to Others
Posts: 276
Registered: 31-8-2020
Location: America Lite
Member Is Offline
|
|
| Quote: Originally posted by The Plutonium Bunny | Does anyone have an idea what this piece is? I recently acquired it in a box labelled "Soxhlet Extractor", but it is rather unlike any Soxhlet I have
seen before. There is no ground glass to be found on the whole thing. Additionally, one of the tubes is positioned such that it drips directly on the
glass frit inside the chamber; the frit leads to another tube exiting the chamber. A final tube leads directly into the glass chamber. There are no
obvious places for attaching a condenser of any kind.
It looks fancy (expensive), but I have no idea what useful purposes it might serve. Thank you for your help in its identification!
|
Just a total guess, maybe something for dissolving gasses in the solution? No clue what the other side tube is for though
|
|
|
| Pages:
1
..
10
11
12
13
14
..
16 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
