draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Unclogging a glass frit
Ok I've used my sintered glass filter for the first time thinking that it would be great for filtering my freshly boiled plant extract and for the
first minute it was,then it slowed down,then it almost stopped.anyway hours later I have a finally filtered solution and a frit full of dirt dust and
small particles of plant matter clogging it up.are there any tips to get it clean I've tried hot water which helped and ethanol got the green out now
I just need to get the brown out.should I try h2so4,or nitric acid? Don't have thf or peroxide
|
|
|
markx
National Hazard
Posts: 646
Registered: 7-8-2003
Location: Northern kingdom
Member Is Offline
Mood: Very Jolly
|
|
Piranha solution would make quick work on that problem, but since you do not have peroxide available I would suggest to give nitric a try.
Harsh cleaning products based on sulfonic acid may also work....at least I have had success with them unclogging glass frits that were gummed up with
organic plant residue.
Exact science is a figment of imagination.......
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Can the 3% h2o2 be used for this
|
|
|
j_sum1
Administrator
Posts: 6333
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
I think that 3% peroxide is likely to be too low to have any real effect. But no harm in giving it a try. Some local pharmacies sell 6% which is
more promising. Either way, be prepared to invest a little time.
Nitric acid is a possibility. That would be my next choice.
Or anything that will break down cellulose. Schweitzer's reagent has been suggested for this before.
You might get success with concentrated oxalic acid or a different reducer. Sodium sulfite is sold to accelerate the decomposition of tree stumps.
|
|
|
j_sum1
|
Thread Moved
20-8-2019 at 23:01 |
Chemetix
Hazard to Others
Posts: 376
Registered: 23-9-2016
Location: Oztrayleeyah
Member Is Offline
Mood: Wavering between lucidity and madness
|
|
If you are careful about how slowly you heat it up you can leave it in a bunsen flame and it should burn off anything organic, I do this for chemists
who have activated carbon stuck in their filters. I have a kiln that goes to 560C and that usually does it, but when I couldn't be bothered running a
kiln for a single item they need quickly, the bunsen trick works.
Welders "pickle " is a 30% solution of HNO3 and 2-5 % HF. If used outside with good skin protections and safely glasses it's safe enough, and it takes
just about anything inorganic away. It's fairly benign on glassware but leaving it on slightly etched or corroded glass overnight or hot will start to
etch into the glass a small amount.
|
|
|
draculic acid69
International Hazard
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Won't be trying that welders stuff HF scares the shit out of me.ill get a bottle of the 6% peroxide and give that a try.im not sure it's 100% organic
I'm sure a good amount of it is literally dirt and bcoz the lawn is so dry every step I take brings up a cloud of dust and i haven't yet come up with
a way to successfully filter this stuff out.im guessing diatomaceous earth would be the way to go.lesson learned.
|
|
|
nimgoldman
Hazard to Others
Posts: 303
Registered: 11-6-2018
Member Is Offline
|
|
I use hot nitric acid, since it is such a strong oxidizer and attacks even metals (sometimes I filter stuff containing copper and silver).
You can concentrate your peroxide, I believe ~10% might work too. Be careful, since addition of H peroxide to sulfuric acid will heat it up a lot
because of the water. Also swirl/stir the Piranha constantly and never add more than say 25% v/v of hydrogen peroxide to prevent explosions.
Also note the glass will heat up a lot, maybe pre-heat it to prevent cracking of the thermal expansion.
I always do this inside a Pyrex dish.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
