thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Making Benzene by Decarboxylation Video
Hi,
I made a video on my new YouTube channel on making benzene by the thermal decarboxylation of sodium benzoate. I would love some feedback on my
presentation and procedure. The procedure was based on NileRed's video on the same topic (with slight modification), as well as the stickied post on
this board.
The link to the video is in my signature. I can't post it here, otherwise I will get IP banned by the filter (long story).
Equipment
For this procedure, I made a dry distillation flask that could withstand the high heat needed. I simply JB welded a 6" pipe to a quart sized paint can
with a couple adapters so I could take the apparatus apart. I used a lot of steel JB weld which stood up to the benzene fumes perfectly. I then filed
down the inside of the 6" pipe so that it would fit my 24/40 glass still head adapter.
To heat, I used a camping propane burner. For distillation, I used a 200mm Liebig condenser.
Summary of Procedure
1. 100g Sodium Benzoate and 60g NaOH were ground finely and mixed in a blender.
2. The powder was put into the paint-can apparatus, and I set up for simple distillation.
3. After 30 mins, white vapor came over and was collected as an orange liquid. Distillate was collected between 60ºC and 140ºC.
4. Orange distillate was washed with 2x 50mL dH2O. Waste water was stored for proper disposal.
5. I set up for simple distillation again.
6. Distillate started being collected in a fore-run beaker at about 74ºC. Then the temperature slowly climbed to 78ºC, where it halted. I initially
thought this was still forerun, so I kept collecting it in the beaker.
7. Then I realized my solution was still wet, so the 78ºC was just an azeotrope. So I switched to a collecting flask.
8. When the distillation terminated, I crudely washed out the boiling flask and put the "fore-run" back in for re-distillation. This time, I collected
anything above 77ºC.
9. The distillate was cloudy, and was dried with anhydrous MgSO4 for an hour.
10. The benzene was filtered through cotton. The result was crystal clear benzene.
Results
I collected 31mL of benzene, which weighed about 26.9g. This corresponds well with the density of benzene, and the disparity could be easily explained
by my cheap scale and mechanical loss in the graduated cylinder. I'm fairly confident that this is close to 100% benzene.
The yield was 50%, which is good considering the yields of 45%-60% reported on the benzene thread. After the dry distillation, I noticed white powder
still remaining, so I believe I could have improved my yield by continuing that initial distillation a bit longer.
Considering the price of my reagents, I calculated that this benzene has a marginal cost of about 11¢ per gram. This is not including the set-up cost
(since it's a marginal cost), nor propane/electricity (I believe that would be a trivial cost), nor time (since this is a hobby, and I enjoy doing it
anyway). The calculations are more thoroughly shown on my YouTube video.
I would greatly appreciate feedback on my video, whether it be about presentation, procedure, or safety.
Thanks,
Thor
|
|
Herr Haber
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
Good video, all the bits and pieces are there (safety, reagents, hardware etc.). You have a good voice (speed, no accent) and obvious editing skills.
The one big difference between your videos and similar ones is the cost analysis. I love details
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Quote: Originally posted by Herr Haber ![](images/xpblue/lastpost.gif) | Good video, all the bits and pieces are there (safety, reagents, hardware etc.). You have a good voice (speed, no accent) and obvious editing skills.
The one big difference between your videos and similar ones is the cost analysis. I love details |
Thank you! I’m trying to improve the smoothness of my presentation. Reading off a word-by-word script makes me sound too mechanical, but no script
and I can’t get a take without a mistake. I might try doing like an outline of keywords next time.
I think cost analysis is pretty important since it’s a big factor in determining whether to buy a reagent or make it. I also want to try to stick to
very OTC-friendly pathways because I hate seeing a cool procedure and then realizing “wait — that chemical is impossible for me to get!”
|
|
morganbw
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 561
Registered: 23-11-2014
Member Is Offline
Mood: No Mood
|
|
I enjoyed the video.
|
|
Amos
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
My two attempts at this yielded between 70% and 80% after re-distilling. I bathed an entire solvent can containing my reactants in open flame and
simply attached and sealed a copper tube to a hole drilled in the lid. Leading the tube down a wide condenser into your receiving flask saves your
glassware from the full onslaught of superheated vapor, which was extremely rapid. If you need more benzene in the future you might take advantage of
that strategy. Your video is nice and professional though, well done. Have a sub on me ![:)](./images/smilies/smile.gif)
[Edited on 7-24-2019 by Amos]
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Quote: Originally posted by Amos ![](images/xpblue/lastpost.gif) | My two attempts at this yielded between 70% and 80% after re-distilling. I bathed an entire solvent can containing my reactants in open flame and
simply attached and sealed a copper tube to a hole drilled in the lid. Leading the tube down a wide condenser into your receiving flask saves your
glassware from the full onslaught of superheated vapor, which was extremely rapid. If you need more benzene in the future you might take advantage of
that strategy. Your video is nice and professional though, well done. Have a sub on me ![:)](./images/smilies/smile.gif)
[Edited on 7-24-2019 by Amos] |
Thanks! I’ll definitely keep that in mind for next time.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5112
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
LOL, that's a pretty clear American accent.
|
|
RedDwarf
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 166
Registered: 16-2-2019
Location: UK (North West)
Member Is Offline
Mood: Variable
|
|
Good video, liked the pace and clarity and I'm also a fan of the economics being included. Do you have a clear idea of what temperature you were
achieving in the can over the course of the reaction?
PS. For an American the accent wasn't too atrocious
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3027
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Nice video! The fact you have a particular accent is helpful as, at least for me, it is easily understandable
I most like the discussion on the mechanism at the end. In the beginning I disliked the explanation about the OTC level of the chemicals, as I think
anyone wanting to make benzene will know about this... but that is something easily overlooked when the rest of the video is (very) good.
Nice result, I think you good get better even yields when you slowly but steadily raise the temperature while having a solid insulation up to the
distillation head. I guess refluxing benzene and side-products back to the reaction medium doesn't do well for the yield.
Edit: you get bonus points for the chicken illustration during the washing step! I'm a biologist ![;)](./images/smilies/wink.gif)
[Edited on 24-7-2019 by Tsjerk]
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Quote: Originally posted by Tsjerk ![](images/xpblue/lastpost.gif) |
In the beginning I disliked the explanation about the OTC level of the chemicals, as I think anyone wanting to make benzene will know about this...
[Edited on 24-7-2019 by Tsjerk] |
I think you're right about this. It definitely felt weird saying "I got sodium hydroxide at the hardware store…" I will keep that in mind next time!
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Quote: Originally posted by RedDwarf ![](images/xpblue/lastpost.gif) |
Do you have a clear idea of what temperature you were achieving in the can over the course of the reaction?
PS. For an American the accent wasn't too atrocious |
Quote: Originally posted by Tsjerk ![](images/xpblue/lastpost.gif) |
I think you good get better even yields when you slowly but steadily raise the temperature while having a solid insulation up to the distillation
head.
|
I had a really hard time controlling the temperature with the propane burner. I couldn't even see the propane flame since it was light out. I started
off too low, and nothing happened. Then I heated too much, and the rate picked up too much and some vapor was making it past. Then I kind of repeated
this cycle a bunch of times until I found the sweet spot. With better temperature control I probably could have improved the yields a bit.
Because of this, I collected distillate from 60º to 140ºC, with the temperature fluctuating up and down quite a bit. I think I may have even turned
off the propane altogether at once point and only noticed because I didn't see the heat waves from the flame...
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3027
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I'm thinking about getting a heating mantle with magnetic stirring for some time now... I have just being cheap until now.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
finally some quality chemistry videos, we have nilered, nurdrage and chemplayer, but all the smaller channels don't put enough effort, in my opinion
most of them are just a video version of a lab note. very well made sir
(i also wanted to make chem videos but my location is sub optimal, and i have an accent, as herr haber pointed out it could be annoying)
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Quote: Originally posted by Tsjerk ![](images/xpblue/lastpost.gif) | I'm thinking about getting a heating mantle with magnetic stirring for some time now... I have just being cheap until now. |
I got my hot plate on a killer deal. This guy was selling his hot plate on offerup for just $100, and I talked him down to $70. After meeting him, he
threw in a ton of glassware too. I think he told me he was using it to make DMT lol... Got 2 KIMAX grad cylinders, a couple erlenmeyers, a weird RBF,
and my hot plate (which was brand friggen new) all for $70. It was awesome.
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Quote: Originally posted by Ubya ![](images/xpblue/lastpost.gif) | finally some quality chemistry videos, we have nilered, nurdrage and chemplayer, but all the smaller channels don't put enough effort, in my opinion
most of them are just a video version of a lab note. very well made sir
(i also wanted to make chem videos but my location is sub optimal, and i have an accent, as herr haber pointed out it could be annoying)
|
Thank you! You should give it a shot, you could always do a voiceover like ChemPlayer does. I was considering doing that in case I ever wanted to make
something that was in a legal grey area like ChemPlayer does. But I opted to just try to avoid those things and use my real voice.
I would suggest a slightly better text-to-speech than chemplayer though
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
I got my hot plate on a killer deal. This guy was selling his hot plate on offerup for just $100, and I talked him down to $70. After meeting him, he
threw in a ton of glassware too. I think he told me he was using it to make DMT lol...
Did you at least ask if he had any of this DMT still lying around???
Well worth the trip if you catch my drift.
|
|
chemplayer...
Legendary
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 191
Registered: 25-4-2016
Location: Away from the secret island
Member Is Offline
Mood: No Mood
|
|
Nice videos - really well done! Looking forward to enjoying more...
|
|
Keras
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 859
Registered: 20-8-2018
Location: (48, 2)
Member Is Offline
|
|
I don't think the accent is that overwhelming. Not much different from NileRed's.
I'm not fun. I just bought a litre of benzene. :p
|
|
VSEPR_VOID
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
Good audio quality. You might also consider using a video style that involves always having something moving on screen to keep the attention of your
audience. Notice how in a NurdRage or NileRed video they are always showing either a time lapse or something being handled.
Be careful with the benzene. It is difficult to communicate just how dangerous it is. If you can smell it you are being exposed.
Within cells interlinked
Within cells interlinked
Within cells interlinked
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Thank you! I absolutely love your videos, one of my favorite channels!
|
|
thors.lab
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 103
Registered: 19-7-2019
Member Is Offline
|
|
Quote: Originally posted by VSEPR_VOID ![](images/xpblue/lastpost.gif) | Good audio quality. You might also consider using a video style that involves always having something moving on screen to keep the attention of your
audience. Notice how in a NurdRage or NileRed video they are always showing either a time lapse or something being handled.
Be careful with the benzene. It is difficult to communicate just how dangerous it is. If you can smell it you are being exposed.
|
Yeah I’ve been working on that. I might try writing an outline of the script BEFORE next time, that way I know roughly what I’m going to spend
time talking about and what I need more footage for.
Thanks!
|
|