Wrecking Bereserker
Harmless
Posts: 25
Registered: 2-4-2019
Member Is Offline
|
|
Allotropes of Sulpher
I'm trying to make allotropes of sulpher but not getting it right these are steps i took help me through it
I tried to dissolve sulpher in CCl4 and heat to evaporate to produce sulphur crytals it didn't work
Then heated a new sample it until it melts and poured it into cold water wich made some tiny balls i don't quite sure what to do after that
Then i heated an another sample until it became sticky this is also an allotrope right?
|
|
12thealchemist
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 181
Registered: 1-1-2014
Location: The Isle of Albion
Member Is Offline
Mood: Rare and Earthy
|
|
There are many allotropes of sulphur. Rhombic and monoclinic are the most common. Rhombic sulphur is stable at room temperature, and is the most
stable allotrope. Monoclinic sulphur is only stable above 95.3°C, and can be prepared by crystallising sulphur at 100°C. Plastic or amorphous
sulphur (μ-sulfur) can be prepared by pouring sulphur heated to above 160°C into water. It is unstable, and over a few days will slowly revert to
rhombic sulphur.
λ-sulphur is the light yellow liquid formed when sulphur initially melts
π-sulphur is formed when λ-sulphur is allowed to sit just above the melting point for an extended period of time. It is a dark colour.
Trisulphur is present in hot boiling sulphur vapour, and is visible as a dark red gas.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3651
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Sulphur is not very soluble in CCl4, 0.8 % w/w
Attachment: Solubilityofelementalsulfur.pdf (42kB) This file has been downloaded 3796 times
so you would have to make a saturated solution, filter it and DISTILL off the CCl4 as the fumes are a health hazard.
CS2 dissolves sulphur easily but is not cheap and its fumes are also undesirable.
I have grown sulphur crystals from sulphur dissolved in toluene,
but the solubility is also quite low, which means wasting valuable solvent (and polluting the air)
or distillation which is a nuisance to set up for a simple experiment.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7999
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Sulphur dissolves quite well in hot toluene, not in cold toluene. I once dissolved some sulphur in toluene, kept at around 100 C and then allowed the
toluene to cool down slowly. I put the test tube with a saturated solution of sulphur in hot toluene in a beaker, which I filled with boiling hot
water. I used a glass tea beaker, which is double-walled, with low pressure between the two glass walls. These beakers keep the liquid warm for quite
some time. In this way, I could make nice shiny crystals of sulphur.
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3027
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I made some really nice slightly yellow needles of sulfur by crystallization from hot toluene.
|
|
12thealchemist
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 181
Registered: 1-1-2014
Location: The Isle of Albion
Member Is Offline
Mood: Rare and Earthy
|
|
I've also recrystallised sulphur from toluene to excellent effect - it's fairly soluble in boiling toluene, far far less so in cold. And since toluene
is impossible to freeze without LN2, you can chill it right down to squeeze out almost all the sulphur you do dissolve.
|
|