itsafineday
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 5-1-2019
Location: "...in them thar hills."
Member Is Offline
Mood: Feelin groovy
|
|
distilled water for diy ph calibration solution ?
Does the ph of distilled water vary much ? Can otc distilled water be used to make diy ph calibration solution ?
I am seeking to level up my Chem skills. Corrections welcome! All mentorship in madness appreciated.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
even distilled water as CO2 dissolved, so its pH is slightly acidic, and can not be ignored. no you can't use distilled water as a calibration source,
it would be too easy![:D](./images/smilies/biggrin.gif)
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
UC235
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
pH of the distilled water means almost nothing since it has no ionic strength and can't be accurately read by a pH meter. Once the buffer salts are
added, they will dominate the pH. However, it is good practice to boil water used to make solutions to expel CO2 and store in tightly sealed
containers.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
i thought he meant just plain distilled water as the calibration solitution, without a buffer
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
I seen one guy use skim milk as a calibration standard apparently it is ph6 exactly.
|
|
CharlieA
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
The pH of pure water is 7, by definition, because the [H+] = 1 x E-7M. Granted that the ionic strength of pure water is very low, I would think that
a decent pH meter would read 7 for a sample of pure water. Certainly to achieve a decent, reliable calibration the use of 1 or more buffer solutions
is well-advised.
|
|
Harristotle
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 138
Registered: 30-10-2011
Location: Tinkerville
Member Is Offline
Mood: I tink therefore I am
|
|
potassium hydrogen tartrate is a NIST primary pH standard.
Buy yourself some cream of tartar, mix it with distilled or rainwater and use a saturated solution as a pH 3.557 at 25 °C
Cheap !
[Edited on 1-4-2019 by Harristotle]
|
|
itsafineday
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 89
Registered: 5-1-2019
Location: "...in them thar hills."
Member Is Offline
Mood: Feelin groovy
|
|
Quote: Originally posted by Harristotle ![](images/xpblue/lastpost.gif) | potassium hydrogen tartrate is a NIST primary pH standard.
Buy yourself some cream of tartar, mix it with distilled or rainwater and use a saturated solution as a pH 3.557 at 25 °C
Cheap !
[Edited on 1-4-2019 by Harristotle] |
Haristotle Kicks A**!
I am seeking to level up my Chem skills. Corrections welcome! All mentorship in madness appreciated.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5111
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
I wouldn't.
If you look at this
https://en.wikipedia.org/wiki/Glass_electrode#Construction
there's picture of a pH electrode, and the bit numbered 7 is the problem
It's a "salt bridge" and it will leak buffer from the probe into the water you are trying to measure.
It's much better to use borax near pH9
There's some talk about it here
http://www.reefcentral.com/forums/showthread.php?t=920017
and cream of tartar near pH 3.6 or (if you happen to have it, potassium biphthalate)
Here in the UK Borax is getting hard to find.
You might end up using something like sodium sesquicarbonate. (near pH 9.9)
|
|