hacker
Harmless
Posts: 34
Registered: 18-12-2018
Member Is Offline
|
|
Removing BrCl from Bromine
How do you remove BrCl from Br2? I have a fractional distillation apparatus. I also have anhydrous sodium bromide.
If I let the contaminated bromine stand overnight over a small amount of NaBr, will fractional distillation remove the BrCl? Is it necessary to filter
before the distillation? I'm not filtering Br2!!
|
|
walruslover69
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 228
Registered: 21-12-2017
Member Is Offline
Mood: No Mood
|
|
It seems like that could probably work, When you fractionally distill you might consider keeping the temperature below the boiling point of bromine
40-50C so as to just drive off the BrCl without losing too much Br2.
I assume you are determining the BrCl contamination gravimetrically? If so it might be a small problem weighing the bromine and getting the volume
with the NaBr in it. I don't think adding or storing it over NaBr is necessary.
|
|
DavidJR
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Personally, I think it's far easier to produce pure bromine in the first place than to try and separate interhalogens.
|
|
fusso
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
What experiment did you do to make a mixture of Br2 and BrCl?
|
|
12thealchemist
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 181
Registered: 1-1-2014
Location: The Isle of Albion
Member Is Offline
Mood: Rare and Earthy
|
|
Tried to make bromine from BCDMH? (1-Bromo-3-chloro-5,5-dimethylhydantoin, a water sanitation chemical)
|
|
hacker
Harmless
Posts: 34
Registered: 18-12-2018
Member Is Offline
|
|
I have not yet performed the experiment. I want to make bromine from BCDMH following the procedure of len1: https://www.sciencemadness.org/whisper/viewthread.php?tid=69...
BCDMH is very cheap.
|
|
clearly_not_atara
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2731
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Sulfuryl chloride exists, but sulfuryl bromide does not, so maybe you can reduce the BrCl with SO2?
SO2 + 2 BrCl >> SO2Cl2 + Br2 ???
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Almost any reducing agent should, in principle, work- use enough to reduce the Br+ to Br.
For example, you could use copper (I'd not use a more reactive metal).
2 BrCl + Cu --> CuCl2 + Br2
Obviously, if you use excess Cu you will lose bromine.
The most satisfactory option is certainly something like NaBr- that way the by-product is also bromine.
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Why don't you use a separatory funnel with a glasswool plug. You can do the reaction overnight in the funnel and after that you can just drain the
bromine.
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6269
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
I don't have it on hand, but Len Lerner's book on small s ale prep of lab chemicals describes a procedure for exfracti g Br2 from BCDMH. IIRC, the
procedure excludes formation of interhalides.
|
|
hacker
Harmless
Posts: 34
Registered: 18-12-2018
Member Is Offline
|
|
Quote: Originally posted by j_sum1 ![](images/xpblue/lastpost.gif) | I don't have it on hand, but Len Lerner's book on small s ale prep of lab chemicals describes a procedure for exfracti g Br2 from BCDMH. IIRC, the
procedure excludes formation of interhalides. |
According to the book, the product is 5% chlorine. On a molar basis, that is almost 10% chlorine!! I want less than 1% chlorine in my bromine.
|
|
hacker
Harmless
Posts: 34
Registered: 18-12-2018
Member Is Offline
|
|
Quote: Originally posted by Tsjerk ![](images/xpblue/lastpost.gif) |
Why don't you use a separatory funnel with a glasswool plug. You can do the reaction overnight in the funnel and after that you can just drain the
bromine. |
Will the vapor pressure blow the cap out of the funnel? Will the procedure scale?
Wow. Do you know the mechanism that liberates bromine from BCDMH and leaves most chlorine behind?
|
|
clearly_not_atara
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2731
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
unionised has a very good idea about using NaBr as the reducing agent. I think this is the way to go. NaBr should not form a stable
tribromide; usually you need Cs+ or a polyatomic cation for that.
Quote: | Do you know the mechanism that liberates bromine from BCDMH and leaves most chlorine behind? |
AIUI it happens because the Br-N bond is longer than the Cl-N bond which gives it a higher dipole moment. That means that the activation energy for
rxn with nucleophilic reducing agents is lower. So you use HSO3- which has right about the desired reducing ability and you work at a temperature
which will achieve the activation energy for Br-N cleavage but not for Cl-N cleavage.
Note that the reducibility/oxidizability of substances is affected by pH, so while this reaction leans left:
SO2 + Br2 + 2 H2O << H2SO4 + 2 HBr
this one leans right:
SO2 + Br2 + 4 OH- >> SO4(2-) + 2 Br- + 2 H2O
[Edited on 23-12-2018 by clearly_not_atara]
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6269
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
Quote: Originally posted by hacker ![](images/xpblue/lastpost.gif) | Quote: Originally posted by j_sum1 ![](images/xpblue/lastpost.gif) | I don't have it on hand, but Len Lerner's book on small s ale prep of lab chemicals describes a procedure for exfracti g Br2 from BCDMH. IIRC, the
procedure excludes formation of interhalides. |
According to the book, the product is 5% chlorine. On a molar basis, that is almost 10% chlorine!! I want less than 1% chlorine in my bromine.
|
Quote: |
Page 81-82
It is interesting to note that with a moderate reducing agent chlorine is reduced much more slowly than bromine, presumably due to the stronger N-Cl
bond of the halogenated amide, so the reaction with a concentrated solution of Na2S2O5 is rapid, and leads quantitatively and almost exclusively to
the reduction of bromine. |
I have not done it but I would tend to take Len's word for it here. At least if the procedure is followed exactly.
|
|
hacker
Harmless
Posts: 34
Registered: 18-12-2018
Member Is Offline
|
|
Quote: Originally posted by j_sum1 ![](images/xpblue/lastpost.gif) |
Quote: |
Page 81-82
It is interesting to note that with a moderate reducing agent chlorine is reduced much more slowly than bromine, presumably due to the stronger N-Cl
bond of the halogenated amide, so the reaction with a concentrated solution of Na2S2O5 is rapid, and leads quantitatively and almost exclusively to
the reduction of bromine. |
I have not done it but I would tend to take Len's word for it here. At least if the procedure is followed exactly. |
In the second sentence on page 81, Len wrote that the upper bound for chlorine contamination is 5%.
![len1.png - 288kB](https://www.sciencemadness.org/whisper/files.php?pid=567574&aid=72666)
I believe Len, but 5% chlorine contamination is far too much. The question is not whether the bromine contains chlorine. We already know that the
bromine is unacceptably impure. The question is how to purify the bromine.
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6269
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
I don't think there is any argument here. And we are both reading from the same source.
It appears that Br2 is extracted preferentially. At a small sacrifice of yield then BrCl production should be eliminated. The claim is if you go to
completion then the interhalide is less than 5%.
Like ] said, I have not done this. And my next Br2 production will be from NaBr. But the source suggests high purity is attainable.
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
https://www.youtube.com/watch?v=HuHceKvSHk0
Best method IMO no secondary halogens used in production.
|
|
hacker
Harmless
Posts: 34
Registered: 18-12-2018
Member Is Offline
|
|
Quote: Originally posted by j_sum1 ![](images/xpblue/lastpost.gif) | I don't think there is any argument here. And we are both reading from the same source.
It appears that Br2 is extracted preferentially. At a small sacrifice of yield then BrCl production should be eliminated. The claim is if you go to
completion then the interhalide is less than 5%.
Like ] said, I have not done this. And my next Br2 production will be from NaBr. But the source suggests high purity is attainable.
|
The source uses different standards for "high purity" than typical. Technical grade bromine is usually 99.5% pure, minimum. 95% is not high purity.
95% is low purity.
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Quote: Originally posted by hacker ![](images/xpblue/lastpost.gif) | Quote: Originally posted by Tsjerk ![](images/xpblue/lastpost.gif) |
Why don't you use a separatory funnel with a glasswool plug. You can do the reaction overnight in the funnel and after that you can just drain the
bromine. |
Will the vapor pressure blow the cap out of the funnel? Will the procedure scale?
|
As long as the bromine has the same temperature as the apparatus and the environment it shouldn't. Only when the surroundings heat up it will
pressurise. To be sure loosely put in the stopper, this way it will just vent and not fly out. Or put a clip on the stopper after you reached your
temperature equilibrium, separatory funnels can handle quite some pressure in case it would heat up.
[Edited on 24-12-2018 by Tsjerk]
|
|