Pages:
1
2 |
AlChemicalLife
Harmless
Posts: 37
Registered: 18-1-2011
Member Is Offline
Mood: happy and ready for science
|
|
Chlorine exposure limit for work
So , I apologize up front for how vague I will be with this but I love my job and Most of it I can't talk about but I have a concern im thinking about
brining up to my work.
At my work we use chlorine , it is in no means a small amount either , a massive amount of chlorine is pumped into our plant daily and we do have
detectors for it.
But as I was reading stuff on chlorine exposure and it says "Workplace exposure limits for chlorine include a short-term exposure limit for up to
15-minute exposures not to exceed 1 ppm (2.9 mg/m−3). That for a long-term exposure limit is for up to 6-hour exposures not to exceed 0.5 ppm (1.5
mg/m−3)."
I work 12 hr days around chlorine and our alarms are set to go off at 0.5 I believe but this seems still a bit high for a 12.25hr day .
Also , some websites have different exposure limits , some that say no more than 0.5ppm for 1hr of exposure.
Some parts of the plant I work in have a much stronger smell , enough to cause my nose to hurt but our alarms still sit at 0 so im also concerned that
the alarms may be defective .
So I guess my question is , Should this be a concern ?
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Yes, I think this really is a concern. First, your alarm MUST work properly. Test it (e.g. by allowing a known amount of Cl2 to escape in a sealed
room of known volume and have the alarm in that room). You could even do the test at home if you can take the alarm with you. E.g. make a test tube
full of Cl2 (22 ml) outside and allow this to escape in a small room (a 3m x 3m room with normal ceiling will have a volume of 22 m3 or so). You then
will have 1 ppm of Cl2. the alarm definitely must trigger.
Besides that, the lower exposures also may be a problem in the long run. It is not incidental exposure, but long term, day after day. I myself am not
too concerned in my experimenting if I occasionally get a whiff of chlorine, but for me it only is once a month or so, and then only for a few
breaths.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3634
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
There will be a person or department responsible for safety, talk to them, raise your concerns.
This department will have, or have access to, monitoring and metering devices or services.
They would probably check your concern for you,
or you could ask to borrow the equipment to satisfy yourself.
If you have serious concerns;
. Talk to your fellow employees, find out what your employers approach to safety is, if you think that there is significant risk that your employer
will not acknowledge risks then start looking for a new employer
. Observe your fellow employees of many years service, do they show any signs of illness ?
. Buy your own calibrated meter, not cheap - unless compared to health costs.
If you do have a significant safety concern, talk to your manager, and the safety guys.
If no action is taken then send a memo !
Once a safety concern becomes formal your employer will investigate rather than risk litigation.
If you do discover any significant safety issues, and follow reporting procedures, but no action is taken, or you are victimised,
then escalate the reporting - manager, safety officer, internal ombudsman, CEO, external safety authorities etc.
YOU are responsible for the safety of yourself, your colleagues and your employer.
P.S. If you look at your alarm sensors there should be a test/calibration date on them !
Look only, do not touch until authorised to do so.
I can not comment on 'safe' levels of anything as I do not know.
DO NOT take chemicals to your workplace or release chlorine gas without prior written approval !
- which will be difficult to get as a risk analysis will have to be performed when introducing a new potential hazard/liability.
[Edited on 30-3-2018 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Radium212
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
I suppose you should bring it to the attention of the whoever runs the place.
|
|
LearnedAmateur
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 513
Registered: 30-3-2017
Location: Somewhere in the UK
Member Is Offline
Mood: Free Radical
|
|
Tests should ideally be run once a week and equipment calibrated every 3-6 months because an alarm can fail at any time and considering that you’re
working with a highly dangerous gas which you can sense yourself, both are extremely important. How often does your workplace test them? If it’s
longer than a month then I’d definitely bring that up.
In chemistry, sometimes the solution is the problem.
It’s been a while, but I’m not dead! Updated 7/1/2020. Shout out to Aga, we got along well.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by AlChemicalLife ![](images/xpblue/lastpost.gif) | So , I apologize up front for how vague I will be with this but I love my job and Most of it I can't talk about but I have a concern im thinking about
brining up to my work.
At my work we use chlorine , it is in no means a small amount either , a massive amount of chlorine is pumped into our plant daily and we do have
detectors for it.
But as I was reading stuff on chlorine exposure and it says "Workplace exposure limits for chlorine include a short-term exposure limit for up to
15-minute exposures not to exceed 1 ppm (2.9 mg/m−3). That for a long-term exposure limit is for up to 6-hour exposures not to exceed 0.5 ppm (1.5
mg/m−3)."
I work 12 hr days around chlorine and our alarms are set to go off at 0.5 I believe but this seems still a bit high for a 12.25hr day .
Also , some websites have different exposure limits , some that say no more than 0.5ppm for 1hr of exposure.
Some parts of the plant I work in have a much stronger smell , enough to cause my nose to hurt but our alarms still sit at 0 so im also concerned that
the alarms may be defective .
So I guess my question is , Should this be a concern ?
|
It's two concerns- firstly does the alarm work.
the second is what concentration should it be set to go off at and you are right, If your working day is longer then the "typical" one then the limit
concentration should be lower.
If you are in the UK (and I think it's the same in the rest of the EU) the document that explains it is here
http://www.hse.gov.uk/pubns/priced/eh40.pdf
It's covered in the schedule on p41
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
When I used to work with phosgene we used a colorimetric dosimeter badge, such badges are available for chlorine:
https://www.a1-cbiss.com/chromair-chlorine-colorimetric-badg...
Even though alarms are going off, many of those alarms are designed to draw from your exit gasses since most everything should be swept to there. It
does not give a sense of what an operator or chemist is really exposed to. A dosimeter badge is going to measure your point of contact to give you an
idea if you are exceeding your TWA for chlorine in a work day. Note that a quick google search gives an odor threshold for chlorine of 0.002 PPM,
what is the limit of detection on your equipment? I bring this up because you might be able to smell chlorine and your equipment may not be
legitimately picking up enough signal to show a reading but you are still operating as intended.
|
|
weilawei
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 130
Registered: 3-12-2017
Member Is Offline
Mood: No Mood
|
|
This sort of decorative alarm philosophy seems present in many jobs. In my job, I'm exposed to toluene, MEK, heptane, and various other organics
daily, for 12 hours at a time, in quantities ranging from 5 gallons up to a thousand gallons. The company refuses to supply respirators (and I'd be
written up for bringing in my own) because they have an "air quality monitoring program" which consists of making sure that certain areas are at an
ever so slight negative pressure. This is from direct conversation with the safety officer and plant manager. They tell me that they are within the
exposure limits--I say, stick your head next to that 5 gallon pail of MEK (without a sealing lid), and then take a deep breath and tell me you didn't
go way over the limit.
The work situation also requires us to handle organic solvents, in confined high-temperature spaces, without ventilation, respiratory protection, or
supplied air. OSHA would have a field day if they ever noticed half the stuff we're ordered to do. We have detectors for flammable atmosphere, but
only in certain locations and they only take action while the equipment is running. During maintenance? There's no protection whatsoever. The people I
work with have had flash fires in tight spaces from static igniting solvent vapors, for example. Thankfully, I have not yet experienced that.
Excuse me, the chemical safety at my work pisses me off--especially when I employ better PPE and handling controls on my own time.
[Edited on 30-3-2018 by weilawei]
|
|
MrHomeScientist
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
You need to report that to OSHA, then. If it's an unsafe working environment, it needs to be fixed. Otherwise it's only a matter of time before
someone gets poisoned or killed, or one of those flash fires gets out of hand and burns the plant down. Don't ignore it!
|
|
sodium_stearate
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 255
Registered: 22-4-2011
Location: guard duty at the checkpoint
Member Is Offline
Mood: No mask.
|
|
If you want to keep this job, then I would
recommend staying low key and being as
anonymous as possible in regards to your workplace
safety investigation.
This is because, in all likelihood they will attempt to make
your work-life miserable as hell if you express your concerns.
Find out for yourself if it's safe or unsafe, then if you choose
to bring it to their attention, do so in such a way that they
do not know who is reporting the unsafe condition.
That way they cannot target you.
"Opportunity is missed by most people
because it is dressed in overalls and it
looks like work" T.A. Edison
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
According to this: www.tandfonline.com/doi/pdf/10.1080/00022470.1969.10466465 the human detection limit for chlorine is 0,3ppm, so any significant smell should be a
red flag.
We're not banging rocks together here. We know how to put a man back together.
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
I see 0.002 PPM here:
https://www.atsdr.cdc.gov/toxguides/toxguide-189.pdf
|
|
AlChemicalLife
Harmless
Posts: 37
Registered: 18-1-2011
Member Is Offline
Mood: happy and ready for science
|
|
As I work around classified stuff , it is very hard for me to go to an osha official, or some random safety officer in my plant and tell them what's
going on as while we all know a bit about what others do in the plant it's all on a need to know basis so I'm worried I will brake my contract and be
put in prison. I can't bring any type of electronics into the plant.
They also seem to think they know so much about the chemicals we use but most of the people who work at our plant have no college education or actual
chemistry experience (or so I am told )
I may get one of those dosimwters and just keep it not visible but that's a risk I have to think about .
The smell is not like the slight smell you get at a pool , it a stong heavy smell , which sometimes feels like it is settling in your lungs.
I do have a bit of a problem of over thinking things when it comes to chemicals but this is one of the situations I think I'm not being as paranoid.
We also work around some other nasty nasty chemicals that will form "sand" in your eyes and lungs if the fumes are released (I'll let you guys figure
out what chemicals those are as I won't say)
All our chemicals are fun through pipes into our machines.
|
|
AlChemicalLife
Harmless
Posts: 37
Registered: 18-1-2011
Member Is Offline
Mood: happy and ready for science
|
|
Quote: Originally posted by LearnedAmateur ![](images/xpblue/lastpost.gif) | Tests should ideally be run once a week and equipment calibrated every 3-6 months because an alarm can fail at any time and considering that you’re
working with a highly dangerous gas which you can sense yourself, both are extremely important. How often does your workplace test them? If it’s
longer than a month then I’d definitely bring that up. |
We have chemicals spill alarm tests almost every day but I don't think they test the meters , just a visual inspection
|
|
AlChemicalLife
Harmless
Posts: 37
Registered: 18-1-2011
Member Is Offline
Mood: happy and ready for science
|
|
Quote: Originally posted by MrHomeScientist ![](images/xpblue/lastpost.gif) | You need to report that to OSHA, then. If it's an unsafe working environment, it needs to be fixed. Otherwise it's only a matter of time before
someone gets poisoned or killed, or one of those flash fires gets out of hand and burns the plant down. Don't ignore it! |
It would be awesome to be able to have an inspector come out but we are tight nit, super secure. Honestly I have no idea why as I'm not told what I
make is used for beside telecom. Other than that all I got is it is supplied to the government for what ever they use our product for...
|
|
AJKOER
Radically Dubious
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
My concern would be also with long term low chlorine exposure combined with dust particles (possible source of transition metals) accumulating in ones
lung. My prior research on advanced oxidation process came across a paper (see "Generation of Hydroxyl Radicals from Dissolved Transition Metals in
Surrogate Lung Fluid Solutions" by Edgar Vidrio, et al at http://www.ncbi.nlm.nih.gov/pmc/articles/PMC2626252/ ) noting that dust particles rich in iron/copper combined with oxygen in the presence of
salt/ascorbic acid is a cyclic recipe for hydroxyl radical formation in your lungs. The attack of the latter radical on the lung's DNA may result in
asthma or even cancer.
In the current case of chlorine, add water vapor, one has HCl and HOCl. The latter hypochlorous acid can even more vigorously engage in a fenton-type
redox reaction than H2O2, also producing hydroxyl radicals (see, for example, "Fenton chemistry in biology and medicine" by Josef Prousek, reaction
(15), p. 2330 at https://pdfs.semanticscholar.org/2b9b/92eff9ca32556c07b1a8cc... ).
Bottom line, even if you and fellow workers are not smokers, I would not be surprised if long term plant workers appear to suffer from a higher
incident of lung diseases.
[Edited on 31-3-2018 by AJKOER]
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
I don't know about your side of the pond, but in the UK the HSE inspectors have stronger "powers of entry" than the police.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by AJKOER ![](images/xpblue/lastpost.gif) |
In the current case of chlorine, add water vapor, one has HCl and HOCl.
[Edited on 31-3-2018 by AJKOER] |
No one does not.
Chlorine clouds are still green even in moist air.
That reaction does, of course, happen in solution- such as in your lungs- but that's always going to happen with chlorine in air.
Please try to stop making everything into a Fenton reaction.
[Edited on 31-3-18 by unionised]
|
|
Magpie
lab constructor
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
When I worked in a pulp mill both Cl2 and ClO2 were used as bleaching agents. It was common to be walking down a hallway and all of a sudden catch a
strong whiff of Cl2. I would just turn around and go back the other way. We had no monitors or other warning devices. It was never even a topic of
conversation. This was in 1966.
The above anecdote is in no way meant to disparage the concerns of others about chlorine. If I thought I was being over exposed I would complain to
management and the safety officer immediately!
[Edited on 31-3-2018 by Magpie]
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
AlChemicalLife
Harmless
Posts: 37
Registered: 18-1-2011
Member Is Offline
Mood: happy and ready for science
|
|
Quote: Originally posted by unionised ![](images/xpblue/lastpost.gif) | Quote: Originally posted by AJKOER ![](images/xpblue/lastpost.gif) |
In the current case of chlorine, add water vapor, one has HCl and HOCl.
[Edited on 31-3-2018 by AJKOER] |
No one does not.
Chlorine clouds are still green even in moist air.
That reaction does, of course, happen in solution- such as in your lungs- but that's always going to happen with chlorine in air.
Please try to stop making everything into a Fenton reaction.
[Edited on 31-3-18 by unionised] |
My plant is super super dry for reasons I can't say besides what we make will not got good with humidity. The humidity is so low in there that I get
zapped pretty often..
|
|
AJKOER
Radically Dubious
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Unionised:
Please some facts. First, the author was invited to contribute to a collection of papers for a 2005 IUPAC project, “Chemistry for Biology”. In
his research, he attempts to explain the relationship between particulate matter (PM) exposure and the reported incidents of lung diseases from a
chemistry perspective. So, working backward, the author's likely logic chain: disease> DNA damage> possible implication of radical induced
causation> presence of transition metals in PM> one likely explanation is a REDOX reaction of transition metals, acid and oxygen producing H2O2
followed by hydroxyl radicals.
A technical point, my understanding is that a ferrous salt REDOX commencing with oxygen (and no H2O2) is not referred to as a fenton reaction.
Next, my substitution of HOCl for in situ created H2O2 together with a source reference for the involvement of fenton-type reaction in biological
process, is not a stretch, in fact, one may claim it is somewhat even obvious.
---------------------------------------------------
Yes, I do research in advanced oxidation processes, which involves strong oxidizers, so just get used to it! In fact, you have just inspired me to
start a new thread on fenton related reactions!!
---------------------------------------------------
A green chlorine cloud in air is pure chlorine gas? You should know better as air is never nearly completely devoid of water vapor at normal
temperatures. Most chemists know that the reaction:
Cl2 + H2O = HCl + HOCl
is an equilibrium reaction. Therefore, some hypochlorous is present and certainly in your lungs with chlorine exposure!
My color analysis of a reputed 'green' chlorine cloud may be insightful (note, chlorine water may vary greatly in color depending on concentration).
First, pure dry Cl2 is yellow-green, with more yellow (its origin is the Greek word "khloros" meaning "greenish-yellow", also a more reactive halogen,
flourine, is yellow with other less reactive halogen being increasing darker in color) as normally mixing equal parts of yellow and green creates so
called grass-green (see https://www.quora.com/When-mixed-what-color-do-yellow-and-gr... ). Next, unstable concentrated HOCl is likely to leak out Cl2O, a brownish-yellow
gas (per Wikipedia, also described as red-yellow) gas. My guess is adding the darker color could tone down the yellowish in pure chlorine resulting in
something closer to a grass-green cloud in moist air (or Cl2 standing over water in a test tube, see https://www.google.com/search?q=&tbm=isch&tbs=rimg:C... ).
----------------------------------------------------
Found an amazing old reference, in line with what I have previously stated in this forum that such old chemical literature references can be
wonderfully in presenting observations, in my opinion. Here is an abstract from a google seach on 'color of chlorine', to quote:
"NOTE ON THE COLOR OF CHLORINE SOLUTIONS.
pubs.acs.org/doi/pdf/10.1021/ja02061a011
by EH Sarles - 1899
into a lower yellow layer, and an upper green layer. The upper layer was a grass-green, not a yellowish green. It seems therefore that chlorine can
dissolve with a green color as well as with the usual yellow color. This fact has apparently been overlooked..."
My tentative explanation based on the limited available details as to the solution's composition or conditions (temperature, present of dissolved
salts, pH, pressure,...) is that the lower layer is contains some undissociated Cl2 and the upper a mix of undissociated Cl2 and Cl2O).
If one assumes the present of contaminants, especially iron, existing in water or from dust exposure, possible action with HCl creating ferrous which
would be oxidized by HOCl to red ferric (in place of Cl2O) contributing to a green coloration (see https://www.hunker.com/13417957/why-did-the-water-turn-yello...).
[Edited on 1-4-2018 by AJKOER]
[Edited on 1-4-2018 by AJKOER]
|
|
AJKOER
Radically Dubious
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by AJKOER ![](images/xpblue/lastpost.gif) | Unionised:
......
Yes, I do research in advanced oxidation processes, which involves strong oxidizers, so just get used to it! In fact, you have just inspired me to
start a new thread on fenton related reactions!!
.......
|
A new fenton thread now exists!
Thank's for the inspiration, it has given me some new ideas to test out!
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
@AJKOER: Chlorine gas has a color quite distinct from color in solution. I prepared a saturated solution of dry Cl2 in CCl4 and this has a bright
yellow color, nothing green in it. Above the saturated solution one can see a very pale green/yellow color, due to a small fraction of gaseous
chlorine in the gas mix above this liquid. A year after making this yellow solution, it still is as yellow as when I prepared it. No change in color,
no loss of color intensity. This is what I expected. It also has been in sunlight quite some time.
Actually, the color of the solution of Cl2 in CCl4 is like the yellow of liquid chlorine. The green color apparently only exists in gaseous form. In
aqueous solution, there is some green color as well. That color, however, is transient. It disappears after a few days (and in sunlight it disappears
after a few hours).
|
|
Panache
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
They followed 1500 ww1 veterans all exposed significantly to chlorine gas wweapobs and found no long term health problems. I’ll try and find the
paper as I don’t remember much about it specifically. Also I know it’s not exactly the same as your situation but my inclination would be to be
less concerned about chlorine, as it’s provably not going to cause you heAlth issues but that culture, if it is as you describe is terriblyrisky in
and of itself. Makes you concerned over other issues that may be ignored. You simply must not do anything in your name. No matter what anyone tells
you. It’s not worth it. Don’t have any faith in ideals.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by AJKOER ![](images/xpblue/lastpost.gif) | Unionised:
A green chlorine cloud in air is pure chlorine gas? You should know better as air is never nearly completely devoid of water vapor at normal
temperatures. Most chemists know that the reaction:
Cl2 + H2O = HCl + HOCl
[Edited on 1-4-2018 by AJKOER] |
"A green chlorine cloud in air is pure chlorine gas? You should know better"
I do know better- that's why I never said that.
It's something you made up, in order to look like you were addressing something I said.
As a "debating" technique, i's called "strawmanning".
And it doesn't work very well because people spot that you are tacitly lying and point it out.
You should know better.
As for "
Cl2 + H2O = HCl + HOCl"
Yes, it's an equilibrium reaction- well enough know to be used in exam questions like this one
https://www3.nd.edu/~skandel/CHEM10181/Main_Page_files/midte...
in which they calculate the concentration of HOCl in eqm with 1 atmosphere of chlorine.
They get
5.92 × 10−3 M
And they also calculate the Cl2 concn.
9.0 × 10−2 M
So, in these conditions there's roughly 20 times as much Cl2 as HOCl.
Now, I realise it's a bit of a stretch, but let's consider what that suggests might be the case in air?
In solution the concentration of water is about 56 M
In air at- say 30% RH (the OP has told us it's quite dry) there's about 7 mg or water per litre of air.
So the concentration of water in air, compared to in water is about
1/3 mM vs 56M
Something like 150,000 times lower.
Since the equilibrium concentration of HOCl depends on the water concentration it's going to be something like 150000 times lower than in solution (I
know, using a solution phase eqm constant to extrapolate to the gas phase is "interesting"- I will come back to it if you like).
So to a very rough approximation, for chlorine at 1 atmosphere in air at 30%RH there will be about 20 X 150,000 times more Cl2 than HOCl.
So, yes, you were not absolutely wrong.
But you were about 99.9999% wrong.
Feel free to try to get better data on the equilibrium, but when push comes to shove, if you mix Cl2 with air you get ...
(drum roll)
a mixture of Cl2 and air with a vanishingly small amount of HOCl and HCl.
Which, in turn, means that you were mainly wrong to say "In the current case of chlorine, add water vapor, one has HCl and HOCl. "
If yo look at the videos here, you can see that bulk chlorine is yellowish green and stays that way.
https://www.uvu.edu/esa/jackrabbit/
|
|
Pages:
1
2 |