VSEPR_VOID
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
Suggestions for Non-volatile, non-Conductive Liquid for Cooling Electronics
In the past mineral oil has been used to some success for the cooling of electronics for high end gaming PCs and concurrency mining machines. It has
the advantage of conducting heat at a greater rate and having a larger thermal capacity than air. With both fluids being able to cycled through the
heat sinks of CPUs and GPUs with normal fans. Mineral oil is relatively cheap, non-conductive, is non-corrosive, non-flammable, and has a both a large
thermal capacity and conductivity. Mineral oil presents several problems for the electrical engineer: It is difficult to clean up, viscous (putting
stress on the fans) and so there is room for improvement.
A replacement or alternative should meet or exceed the following criteria:
Is non-conductive
Is non-corrosive
Has a competitive price
Has a lower or similar viscosity
Is Non-flammable and preferably non-volatile
Is non-viscous and is able to be moved by standard cooling fans
Is thermally conductive
Has preferably a high thermal capacity
Does anyone here have any experience in cooling electronics with liquids? Does anyone know of a liquid with these, or some of these, properties?
I would like to see what crazy ideas we can come up with.
Within cells interlinked
Within cells interlinked
Within cells interlinked
|
|
ninhydric1
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 345
Registered: 21-4-2017
Location: Western US
Member Is Offline
Mood: Bleached
|
|
Isn't water a viable option?
The philosophy of one century is the common sense of the next.
|
|
AJKOER
Radically Dubious
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Distilled water prepared under an atmosphere of say nitrogen, removing any dissolved oxygen, which could lead to reactive oxygen species.
Meets many of the criteria. For example, pure water doesn't have enough ions to conduct electricity, is cheap, non-corrosive except for highly anodic
metals, low viscosity, non-flammable, non-volatile, non-viscous, and thermally conductive.
[Edited on 4-2-2018 by AJKOER]
|
|
VSEPR_VOID
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
Quote: Originally posted by AJKOER ![](images/xpblue/lastpost.gif) | Distilled water prepared under an atmosphere of say nitrogen, removing any dissolved oxygen.
Meets many of the criteria. For example, pure water doesn't have enough ions to conduct electricity, is cheap, non-corrosive except for highly anodic
metals, low viscosity, non-flammable, non-volatile, non-viscous, and thermally conductive.
|
I thought about that. For closed systems that will not have contact with normal atmospheric gases, and not come into contact with sensitive components
it would work. I do not think that gamers and miners would or could use it. Having to seal everything against CO@ would be too difficult.
Within cells interlinked
Within cells interlinked
Within cells interlinked
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3649
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Why the requirement for the fluid being an electrical insulator ?
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
wg48
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 821
Registered: 21-11-2015
Member Is Offline
Mood: No Mood
|
|
I recall seeing a small portable television operating in a tank of what I recall as a silicone oil. It was a display to demonstrate its inertness
for cooling electronics.
Here is a pc in mineral oil:
|
|
VSEPR_VOID
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
The fluid is in contact with all the bare electronics. Imagine how a computer would fair is air suddenly was conductive, it would be a light show
followed by the release of some magic black smoke.
Within cells interlinked
Within cells interlinked
Within cells interlinked
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Propylene glycol? While it is flammable, its low volatility makes it pretty difficult to ignite, especially accidentally. The most annoying thing
about it is that it's sticky if you accidentally spill it, and doesn't readily evaporate.
Silicone oil is good if propylene glycol isn't good enough.
Perfluorodecane is probably like, the gold standard here.
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
Σldritch
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 309
Registered: 22-3-2016
Member Is Offline
Mood: No Mood
|
|
Anything fluorinated that heavily will probably have pretty bad specific heat capacity because atomic heat capacity is fairly constant for the
elements so the more light elements the better. But perhaps density makes up for it in some cases. Alkanes are probably the best though, you should
be able to sacrifice some non volatility for viscosity.
Of course the obvious answer is a NaK cooled computer. Or mercury if you are at risk of spilling your drink on it.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Σldritch ![](images/xpblue/lastpost.gif) |
Of course the obvious answer is a NaK cooled computer. Or mercury if you are at risk of spilling your drink on it. |
Doesn't really meet the "non conductive" requirement
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1314
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
In my opinion, total immersion of a PC for liquid cooling is unnecessary, risky, and possibly counterproductive.
Unnecessary : There are only a few places where extreme cooling is actually beneficial, such as the CPU, GPU and memory. The rest of the PC gains no
benefit, considering it has been designed to work well with just air cooling (and often passive air cooling at that)
Risky: There are a number of plastic components in a PC - some of these may degrade with long term contact with oils. Don't really want the CPU socket
falling apart, do we? Also the excessive loading on fans designed for the speed/torque curve of pushing air - thats going to occur with any liquid,
no matter how runny it is, as the liquid density will be close to 1000x that of air.
Counterproductive: PC motherboards contain many traces delivering high speeds signals with harmonics reaching into the GHz. Adding a liquid
dielectric to the top of these carefully designed traces is going to change the impedance, loss characteristics and group-delay characteristics of the
signal path. You may have noticed traces with squiggly bits : these are for delay matching between traces. This means a real chance of bit errors
creeping in, or at least a greater susceptibility to interference, with a corresponding crash.
Much better to use closed loop cooling with liquid heatsinks on the hot spots - then you can use the best liquid of the lot , which is water.
[Edited on 4-2-2018 by Twospoons]
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2692
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Just put the whole thing in L2N or liquid helium. That is how they cool quantum computers. I think that would keep them cool enough.
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7998
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I agree fully with Twospoons. Modern computers work in the GHz range and this requires careful design of signal paths. These signals paths can be
quite long (order of magnitude of 10 cm) and very close to each other (0.1 mm or so) through very thin traces. If you immerse such a trace in a
liquid, then expect the capacitive coupling between the traces to be quite different from what it is when the traces are separated by air. I expect
total failure of the PC when it is immersed in some liquid. The high-frequency behavior simply changes too much. Only the CPU, GPU and possibly the
memory need to be cooled.
|
|