Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Any interest in a magnetic stirrer that can cycle speed/direction automatically?
We've probably all experienced a magnetic stirrer that went a bit too fast, eventually clanking around the vessel instead of stirring like it was
supposed to. To make it stop, of course, you have to turn the stirring off, or at least down very low. Then the magnets align, and you can turn the
speed up again. There's also an issue where, over time, there will be "sand dunes" of a solid reagent that get stuck to the bottom, where they form
because of the consistent fluid flow over them. To solve both problems, I was thinking that perhaps a stirrer could stop and change directions every
five minutes or so. It would go the same speed as it was set to, just the opposite direction, and adjusting the speed would reset the timer on the
cycle so that it would never change directions in the middle of adjusting the speed. I was about to build the thing finally, but figured I'd ask here
to see if there were any considerations I should be sure to keep in mind.
The motor I have is actually from an old videodisk player, and was made by Sony. It's actually a perfect DC stirrer motor, I think. Very smooth
motion at all times.
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3649
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
maybe just changing the size and/or shape of the stirbar would be easier ?
e.g.
http://www.ebay.co.uk/itm/PTFE-Magnetic-Stir-Bars-High-Magne...
http://www.ebay.co.uk/itm/PTFE-Magnetic-Stirrer-Gear-Type-Oc...
http://www.ebay.co.uk/itm/Bel-Art-Products-371520000-Spinbar...
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
VSEPR_VOID
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
You could always make a controller such as that. With a motor controller, RTC, and an ardiuno you could construct such a device.
Within cells interlinked
Within cells interlinked
Within cells interlinked
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Quote: Originally posted by VSEPR_VOID ![](images/xpblue/lastpost.gif) | You could always make a controller such as that. With a motor controller, RTC, and an ardiuno you could construct such a device.
|
That was actually the plan. The stirrer on my hotplate is broken, and rather than just use it without a stirrer, I figured I'd replace it with a
custom-made one. I have an H-bridge motor controller, (to switch polarity on the motor) and since the motor only draws about 100-200 mA, the
controller should work fine without any power-boosting circuitry. I mounted the original permanent magnet onto the new motor already, now I just need
to build a mount to hold the motor in place inside the hotplate, hook up the stirrer potentiometer, then write the arduino code. I took apart an old
12V 500 mA AC adapter, and that circuitry should be able to provide the necessary DC power to the system, and can be hooked up internally. But if I'm
going to be putting an Arduino in there, I feel like I should add more functionality too, while I'm at it. Of course, I'd then need to add more
controls somehow, or hook up a bluetooth module and use my phone to control and write control software for my phone or something... but I should
probably just focus on the stirring for now.
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
CRUSTY
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 139
Registered: 5-6-2016
Location: Nearby
Member Is Offline
Mood: High-Order
|
|
For those who prefer something that doesn't involve Arduino or programming for that matter, you can build the entire controller circuit for $5-15 USD:
You can get the "relay" there (a double-pole double-throw) for less than $5 (usually), and control the relay using a 50% duty-cycle 555 timer circuit,
which costs MAX $4. Probably cheaper. Personally, I'd prefer Arduino though.
EDIT: God dammit, images are such a pain.
![DPDT-relay.png - 16kB](https://www.sciencemadness.org/whisper/files.php?pid=493206&aid=61649)
[Edited on 29-9-2017 by CRUSTY]
|
|
VSEPR_VOID
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
Quote: Originally posted by Melgar ![](images/xpblue/lastpost.gif) | Quote: Originally posted by VSEPR_VOID ![](images/xpblue/lastpost.gif) | You could always make a controller such as that. With a motor controller, RTC, and an ardiuno you could construct such a device.
|
That was actually the plan. The stirrer on my hotplate is broken, and rather than just use it without a stirrer, I figured I'd replace it with a
custom-made one. I have an H-bridge motor controller, (to switch polarity on the motor) and since the motor only draws about 100-200 mA, the
controller should work fine without any power-boosting circuitry. I mounted the original permanent magnet onto the new motor already, now I just need
to build a mount to hold the motor in place inside the hotplate, hook up the stirrer potentiometer, then write the arduino code. I took apart an old
12V 500 mA AC adapter, and that circuitry should be able to provide the necessary DC power to the system, and can be hooked up internally. But if I'm
going to be putting an Arduino in there, I feel like I should add more functionality too, while I'm at it. Of course, I'd then need to add more
controls somehow, or hook up a bluetooth module and use my phone to control and write control software for my phone or something... but I should
probably just focus on the stirring for now. |
You could design a housing and have it 3d printed from 3dHubs
Within cells interlinked
Within cells interlinked
Within cells interlinked
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
I actually have the stirrer motor in there now, but hooked up to an adjustable DC power supply that's primarily for things like electrosynthesis and
electroplating. The wires are running out one of the vent slits on the hotplate, and the motor was just mounted with this double-sided foam tape
stuff, to keep it from rattling too much. So far, it's worked okay, but I feel like I'd need a pretty good incentive to finish fixing it.
How much do things like enclosures cost to have made? It'd probably need to be a fairly heat and chemical resistant type of plastic, for a mount
that'd be inside a hotplate.
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|