LD5050
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 182
Registered: 16-1-2017
Member Is Offline
Mood: No Mood
|
|
Begginer electrochemisty projects?
I was wondering if I could get some ideas and help from some of you on some ideas pertaining to electrochemistry. I was thinking of building an
electrolysis setup to further my knowledge on the subject. Right now I know pretty much nothing on the subject. I am horrible with electricity but I
find it interesting.
For starters maybe making iron oxide? I saw a quick video where they fill a container with a saturated sodium chloride water solution and use a nail
and a thin wire for the electrodes.
Also I saw something a while back making benzaldehyde from toluene from such a process.
Any suggestions on where I could start to gain a good understanding of this? What are common power sources ? I think I have seen people use lap top
chargers and such. In the mean time I will do some digging of my own but I was hoping maybe some of you could shoot me some ideas. Thanks
[Edited on 7-27-2017 by LD5050]
|
|
JJay
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
Sodium bromate is a good one. Chrome plating. I use a lab power supply that allows regulating the voltage or current, but a lot of people use cell
phone chargers and such things.
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1638
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Start with water cracking once you can get good results with a clean cell then move on from there as making h2 and o2 is very forgiving to oop'ses
Then move on to a chloral-Alkali cell (Bubble the chlorine through sodium carbonate or bicarb)
Start with a 12V iron core battery charger and a motor speed controller to adjust the voltage, light dimmers will work if they will handle an
inductive load. and a good volt and amp meter.
[Edited on 27-7-2017 by XeonTheMGPony]
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
You could make some sulfuric acid from concentrated CuSO4 solution using a lead anode.
You get some good practice an the Faraday equations as well as general practice. The bonus is that you get some dilute H2SO4 which you can
concentrate if needed. You also get a pretty good lead dioxide anode that you can use for other electrochemistry projects.
edit: typo
[Edited on 28-7-2017 by j_sum1]
|
|
violet sin
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1477
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
I love electro chem, spent hours upon hours tinkering away, learning from the source itself. I'm US based so bear that in mind ...
1) Get a harbor freight digital multimeter for free when you spend 5$ on anything else there. Get a few if you can. No use in fudging up a 60$
unit learning.
2) get an old ATX power supply if you can from a bunk PC. Use YouTube to figure how to wire it up. That will give you 12v, 5v, 3.3v . Or eBay has
some ZVS power supplies for cheap. Phone chargers only gonna give you 5v at somewhere between 500mA and 2A.
3) buy/find/salvage some copper wire that is decently thick .. say 12ga - 14ga would be good, 14 is smaller of the two.
4) Get a couple dedicated containers from dollar store or thrift store. Soda bottles and jars can be easy to tip over. At least get a larger guy to
put stuff in while powered, as a catch tray. You down want to spill electrified sol down the front of you
5) start gathering a few things from around the house and play. Epsom salt, baking soda, table salt, these will work as electrolytes.
6) my fave,... Have fun ![:)](./images/smilies/smile.gif)
-----------------------
It's a lot easier to see how things react in person all hands on and what not.
Electrode size, spacing between, surface area and shape all contribute. Start to get an idea how long it's going to take to accomplish things by
watching how fast copper corrodes into solution. Learn the balance between speedy and slow for your power source, then of course dream of having more
power, then realize just more.. is a bad idea. It has to be the proper version of more to do anything useful.
What fun it was learning all that the first time and if your making copper
hydroxide (copper hydroxy-carbonates) it's really REALLY hard to mess up. But the product can be cleaned and roasted to make black copper(II) oxide.
After you get the hang of it, the field opens endlessly !!! All dependant on how much you read, what upgrades you get for equipment, etc. If you
feed it, it will grow
|
|
PirateDocBrown
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 570
Registered: 27-11-2016
Location: Minnesota
Member Is Offline
Mood: No Mood
|
|
violet sin is right about ATX supplies.
Not only can they give you their rated voltages, but you can use them to give voltages that are the differences between them.
12-3.3 = 8.7
5-3.3 = 1.7
12-5 = 7
So you have 6 possible voltages. They have good current outputs, too, I was getting nearly 20 amps at 12v. And if you burn one out, they are cheap! I
can get used ones from a local surplus store for $5.
There are nice rectangular glass vases I spotted the other day that would make great electrochemical cells. They looked like 8x8 glass blocks, cut in
half. (Maybe they were)
Certainly look for scrap copper. You can cut a water pipe on one side and flatten it out, to make a long and narrow, but thick, strip, perfect as an
electrode.
Also some plastic tubs, for spill containment.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Just a small side note:
I recently ordered a digital multimeter, AN8002 (aka ZT102), it is in the post.
If anyone is interested I can give a review when it arrives but there are many reviews online, and not only is it useful for the volts and amps etc.
it comes with a thermocouple probe to measure temperature, which is also important in electrochemistry.
Sorry if already mentioned, the most important part https://en.wikipedia.org/wiki/Standard_electrode_potential_(data_page)
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Review of AN8002 Digital Multimeter
Excellent value;
. very clear display w/backlight, stable readings, all ranges tested so far well within specifications
e.g. Weston Cell, 1.01859 V reads as 1.017 ... one digit / 0.1 % error vs spec. of 0.5%.
the capacitance range is useful and accurate.
All ranges auto-zero. comes with thermocouple probe and a cute bag so you don't scratch your cute meter.
Fuses on volts and amps terminals, tested on 240 Vac no problem.
If you are looking for a cheap but good dmm, I recommend the AN8002
(no, I'm not getting any reward for promoting it ![:)](./images/smilies/smile.gif)
Aneng AN8002 = Zotek ZT102 = KASUNTEST ZT102 = other aliases
eBay, Amazon, Banggood etc. all sell it.
This meter should meet most requirements of members here.
.........................................................................................
There are other models in the range, e.g. the AN8008 10,000 count, 1 uV resolution BUT 10mA and 100mA ranges absent !
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
wg48
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 821
Registered: 21-11-2015
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by PirateDocBrown ![](images/xpblue/lastpost.gif) | violet sin is right about ATX supplies.
Not only can they give you their rated voltages, but you can use them to give voltages that are the differences between them.
12-3.3 = 8.7
5-3.3 = 1.7
12-5 = 7
|
That is not possible because if current flows into the positive supplies the voltage will attempt to rise. Depending on the particular configuration
of the power supply that can damage it or cause the over voltage/regulator circuit to operate in an attempt to stop the rise in voltage.
That can also happen if you attempt to draw current from the negative voltages.
That’s also true of bench power supplies unless they a specifically designed to operate that way and most are not.
Edit: removed the reference to the common 0v as its not relevent in this context.
[Edited on 19-8-2017 by wg48]
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Quote: Originally posted by Sulaiman ![](images/xpblue/lastpost.gif) | Excellent value;
. very clear display w/backlight, stable readings, all ranges tested so far well within specifications
e.g. Weston Cell, 1.01859 V reads as 1.017 ... one digit / 0.1 % error vs spec. of 0.5%.
the capacitance range is useful and accurate.
All ranges auto-zero. comes with thermocouple probe and a cute bag so you don't scratch your cute meter.
Fuses on volts and amps terminals, tested on 240 Vac no problem.
If you are looking for a cheap but good dmm, I recommend the AN8002
(no, I'm not getting any reward for promoting it ![:)](./images/smilies/smile.gif)
Aneng AN8002 = Zotek ZT102 = KASUNTEST ZT102 = other aliases
eBay, Amazon, Banggood etc. all sell it.
This meter should meet most requirements of members here.
.........................................................................................
There are other models in the range, e.g. the AN8008 10,000 count, 1 uV resolution BUT 10mA and 100mA ranges absent ! |
Does it shut itself off if you forget to turn it off for an hour or so? That's the main problem I have with my current one, is that it doesn't.
That, and it takes a 9V battery, and those cost like $5 if I want to buy one from anywhere nearby.
Oh, by the way, for electrochemistry, current and current density is more important than voltage. Phone chargers actually work better than a
lot of the solutions that people here are describing, because they max out at their rated current or voltage, whichever is reached first. This is
necessary because a lot of phones can be charged faster than chargers can supply power, and because really, batteries are a case of electrochemistry
too. So assuming you have a phone charger rated at 5V and 1000mA, you can just measure the voltage across it, and if it's below 5V, you know the
current exactly. You can also use multiple chargers in parallel, since the circuit in cell phone power supplies is different from a voltage
regulator, and doesn't experience the same problems when using them in parallel.
Also, for like $3, you can get one of these things, which is far less prone to damaged wires than any I've made myself from old cables:
http://www.ebay.com/itm/201657672492
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Yes it has auto-power-off, after 14 minutes of inactivity the meter gives a few warning beeps, then at 15 minutes it powers down with a last beep.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Quote: Originally posted by Sulaiman ![](images/xpblue/lastpost.gif) | Yes it has auto-power-off, after 14 minutes of inactivity the meter gives a few warning beeps, then at 15 minutes it powers down with a last beep.
|
Nice. And it uses AAA batteries too, which are easy to come by. I ended up getting the AN8008 version for like $20, since it comes with leads that
you can replace the tips on. So you can have your ground, as say, an alligator clip or a screw terminal, and have the other lead be a regular probe.
It can also measure frequency and count pulses, which should substantially reduce the frequency with which I wish I had an oscilloscope.
edit: To stay on-topic, I've been considering setting up a stannous chloride electroreduction cell in HCl that would reduce SnCl4 to SnCl2, and
recycle it constantly, so you don't get a ton of tin salts in your workup. It'd have to be a divided cell though, presumably with SnSO4 on the other
side, to prevent electrode damage. The membrane could be made from thick polyester cloth, which isn't damaged by HCl significantly.
[Edited on 8/21/17 by Melgar]
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
For £6.75 I can get two 6V lantern batteries (zinc chloride) delivered to me,
that gives four cells to use as a power supply (1.5V, 3V, 4.5V, 6V)
and four cells to dissect to obtain;
. Four carbon rods (to use as electrolysis electrodes)
. very pure zinc
. manganese dioxide (mixed with carbon and zinc chloride)
. a piece of zinc chloride impregnated paper
combined with metals and electrolytes found around the home,
there are few limits.
[Edited on 22-8-2017 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|