Elemental Phosphorus
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 184
Registered: 11-11-2016
Location: Is everything
Member Is Offline
Mood: No Mood
|
|
Efficiency of a car’s catalytic converter
There has been some interest in making sulfuric acid using sulfur and air, but decent catalysts to oxidize SO2 to sulfur trioxide seem to be few and
far between. Vanadium pentoxide has been discussed and I happen to have a quarter pound of it. A catalytic converter would be ideal for me because I
would have to find a way to bind the pentoxide to a proper membrane. What is the efficiency of a catalytic converter in oxidizing sulfur dioxide? Will
it only oxidize >1% or will it work almost quantitatively? Does anyone know or will I just have to try to find drain cleaner or use vanadium
pentoxide?
Vanadium Pentoxide:
|
|
Douchermann
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 117
Registered: 11-10-2005
Location: Illinois, USA
Member Is Offline
Mood: No Mood
|
|
Looked up some patents and it looks pretty promising actually. This has a wealth of knowledge not just in itself but in references to other patents:
https://patents.google.com/patent/US5175136A/en?q=sulfur+tri...
A few speak specifically of platinum doped "honeycomb bodies with a cell density of 100 cells per square inch" - i.e. pretty much exactly a catalytic
converter.
I'd say cut one off your buddies car and give it a test. Kidding - they're plentiful in junkyards. A lot of what I read described relatively low
temperatures - around the same temp the catalytic converter runs off hydrocarbons and CO.
It\'s better to be pissed off than to be pissed on.
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
IIRC, the problem with platinum group metals as catalysts for the contact process is that they foul too easily, and sulfur is famous for its ability
to foul catalysts. That's why V2O5 was such a huge breakthrough: it's very resistant to fouling.
|
|
Elemental Phosphorus
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 184
Registered: 11-11-2016
Location: Is everything
Member Is Offline
Mood: No Mood
|
|
Well looks like vanadium pentoxide it is then. The plan is to deposit it on silica gel, and pack that in a glass tube with 2 openings at one side, one
for air, the other for sulfur dioxide. I could try and fuse a ground glass joint to the end, or just absorb the product in sulfuric acid. I am leaning
toward the second one, since I really wanted the sulfur trioxide for oleum anyway, but maybe I'll also end up making thionyl chloride.
|
|
Lambda-Eyde
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 859
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
Fleaker did this with great success almost 10 years ago: https://www.sciencemadness.org/whisper/viewthread.php?tid=89...
This just in: 95,5 % of the world population lives outside the USA
You should really listen to ABBAPlease drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
Elemental Phosphorus
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 184
Registered: 11-11-2016
Location: Is everything
Member Is Offline
Mood: No Mood
|
|
Thanks for showing me that thread. I will be replicating his design with a few changes. I started this one to ask if a car's catalytic converter could
be used, but it's probably better for me just to use the pentoxide.
|
|
Elemental Phosphorus
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 184
Registered: 11-11-2016
Location: Is everything
Member Is Offline
Mood: No Mood
|
|
Thanks, I hadn't seen that thread but thanks. I will try to replicate his setup (with some modifications). I created this thread to ask if a car's
catalytic converter could be used, but looks like the pentoxide is the better choice.
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
You could use the catalytic converter ceramic as the substrate for your catalyst, if you already have it. And after looking into it, I learned that
arsenic, not sulfur was responsible for fouling catalysts when they tried to use platinum early on for the contact process. Sulfur does foul palladium
catalysts, but perhaps not platinum.
|
|
Jstuyfzand
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 166
Registered: 16-1-2016
Location: Netherlands
Member Is Offline
Mood: Learning, Sorta.
|
|
Could the converter be used for the Ostwald process? The platinum is there and I don't think there is a large amount of palladium and rhodium in
there.
Of course the yields would be lower, pressurizing would be difficult, but it might be usable
|
|
Elemental Phosphorus
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 184
Registered: 11-11-2016
Location: Is everything
Member Is Offline
Mood: No Mood
|
|
Catalytic converters in the Ostwald process
A catalytic converter should work well for the first step of Ostwald process (ammonia to nitric oxide), since according to the wikipedia page:
Ammonia is converted to nitric acid in 2 stages. It is oxidized by heating with oxygen in the presence of a catalyst such as platinum with 10%
rhodium, to form nitric oxide and water. This reaction is strongly exothermic, making it a useful heat source once initiated:[3]
4 NH3 (g) + 5 O2 (g) → 4 NO (g) + 6 H2O (g) (ΔH = −905.2 kJ/mol)
But it may cause problems since one function of a standard, modern 3-way catalytic converter is to reduce nitrogen oxides to nitogen and oxygen. If
you can get an older, 2-way catalytic converter, that should work without problems.
|
|
Melgar
Anti-Spam Agent
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Three-way catalytic converters can only reduce all three pollution classes when there's a constant feedback loop with the vehicle's engine, because
the operating range is so narrow. If your goal was conversion of ammonia into nitric oxide, you'd just have to operate at different conditions that
favor its formation. Keep in mind that at least in the case of PGMs, catalysts lower the activation energy of reactions in BOTH directions.
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
Morgan
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1675
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
Tidbit
http://www.mse.engr.uconn.edu/why-pt-survives-but-pd-suffers...
|
|
Elemental Phosphorus
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 184
Registered: 11-11-2016
Location: Is everything
Member Is Offline
Mood: No Mood
|
|
Well, this isn't really the thread for discussion of the Ostwald process, and my question has already been resolved.
But, I found some more information that should certainly be interesting for those that wish to carry out the Ostwald process at a reasonable price on
a small scale.
Manufacturing Nitrates: the Ostwald process
Once ammonia has been produced by the Haber process, it can be converted into nitric acid through a multi-step procedure known as the Ostwald process.
In the first step in this reaction, ammonia and oxygen gas catalytically react to form nitrogen monoxide:
4NH3(g) + 5O2(g) 4NO(g) + 6H20(g) H = -906 kJ
(1)
The reaction is quite exothermic. In the commercial reaction, the catalyst used in a platinum-rhodium metal gauze that is heated to about 900 oC.
!! However, even a hot copper wire can catalyze the reaction in the laboratory.!!
Once the reaction has started, the energy it produces is enough to keep the catalyst hot enough to sustain reaction.
In the next step, the NO reacts with oxygen to produce NO2. No catalyst is required for this reaction, as it will occur in air at room temperature.
2NO(g) + O2(g) 2NO2(g)
Copper will catalyze the first reaction. This source refers to a 'hot copper wire', but a few copper wool scrubber pads in a quartz or stainless steel
tube should work, provided the tube is well heated. If you don't have access to a catalytic converter, this could be very helpful.
There is already a thread for the Ostwald process though, so maybe it is best to continue this discussion there.
Edit: In the Ostwald process thread, it was said that copper did not work in practice. When I read that, I thought that the problem could be
relatively easily circumvented by decreasing the surface area, increasing the flow rate, or decreasing the overall length of the catalyst tube. There,
it was said that nickel oxide worked excellently, and nickel is not that hard to get either, so that is an option as well.
Chemetix did a lot of great work on this and if you are interested I highly recommend you check out his setup. My interest was in oleum, not nitric
acid, since nitrate salts are readily available where I live.
[Edited on 13-6-2017 by Elemental Phosphorus]
|
|
Jstuyfzand
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 166
Registered: 16-1-2016
Location: Netherlands
Member Is Offline
Mood: Learning, Sorta.
|
|
I remember reading somewhere on this forum that copper catalyzes it too well and turns the ammonia into N2 and H2O, too quick to form any NO2.
|
|
Texium
|
Thread Moved 27-11-2023 at 11:27 |