Ashot
Hazard to Self
Posts: 79
Registered: 9-7-2016
Member Is Offline
Mood: No Mood
|
|
How to remove rust in few minutes.
Please take a look at this video where I am removing rust from a very old file in a few minutes.
https://www.youtube.com/watch?v=-IEi-eszJtM
In the next video, I am planning to galvanize the same file to prevent it from rusting further.
If you like my videos and want to know exactly when I am uploading a new video, you can subscribe to my channel.
Rust is an iron oxide. The reaction of iron metal and oxygen in the presence of water or air moisture.
For the demonstration, I found an old file that was rusting for at least couple of years. This demonstration is not designed for the domestic use as
it involves a highly corrosive acid and corrosive fumes. However, this process is very efficient and widely used in industry.
For domestic rust removal, I would recommend soaking rusted objects in vinegar for 24 hours or using commercially available chemicals such as WD-40.
Thank you very much for watching my videos.
I will appreciate any advice on how to improve.
|
|
|
j_sum1
Administrator
Posts: 6335
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
Nicely prepared video. And remarkably effective process.
Concerning your next proposed step -- The problem with galvanising a file is that zinc is soft whereas your file is hard martensitic steel. Any
coating you apply will come off pretty quickly in use. The little that remains deep in the grooves of the file will have a sacrificial anode effect
and will still continue to protect the file a bit. But that same material will limit the effectiveness of the file.
Galvanising a file is not something that I would do -- except as a demo. Other tools, maybe.
|
|
|
Ashot
Hazard to Self
Posts: 79
Registered: 9-7-2016
Member Is Offline
Mood: No Mood
|
|
Hi, thank you for a feedback I really appreciate it.
Yes, I have to agree with you regarding galvanization of file it is totally pointless.
However, this old file is the only rusted tool I could find and I will galvanize it only for demonstration. I believe it would be a good idea
explaining why I am galvanizing the file.
Thanks
[Edited on 10-8-2016 by Ashot]
|
|
|
Maker
Harmless
Posts: 46
Registered: 1-11-2015
Member Is Offline
Mood: No Mood
|
|
Allowing a files to rust, then cleaning them with acid is an effective sharpening method.
|
|
|
Dank
Harmless
Posts: 8
Registered: 10-4-2016
Location: USA
Member Is Offline
Mood: Wet
|
|
Any idea how effective this would be for removing hydrated Fe2O3 from a glass frit? I've already tried soaking in hot HCl a few times and it's not
going anywhere..
|
|
|
Ashot
Hazard to Self
Posts: 79
Registered: 9-7-2016
Member Is Offline
Mood: No Mood
|
|
Hi, try soaking it in oxalic acid for 24 hours. To be honest, I can't see why hydrochloric acid didn't work perhaps because this is not iron oxide? If
oxalic acid won't work try isopropanol.
|
|
|
Dank
Harmless
Posts: 8
Registered: 10-4-2016
Location: USA
Member Is Offline
Mood: Wet
|
|
There was a small amount of Cr2O3 as well but this should react with HCl as well to form CrCl3 (which is soluble), no? I don't have any oxalic acid
on hand though so I'll give isopropanol a shot. I thought the sodium carbonate was placed on the tool to sort of "blast" the rust off, but correct me
if I'm wrong.
|
|
|
diddi
National Hazard
Posts: 723
Registered: 23-9-2014
Location: Victoria, Australia
Member Is Offline
Mood: Fluorescent
|
|
I cannot imaging that the file would be sharp after having its edge burnt off. It would be ok for certain tools, but I will defer to using a wire
wheel to clean my files.
Beginning construction of periodic table display
|
|
|
Ashot
Hazard to Self
Posts: 79
Registered: 9-7-2016
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by diddi  | | I cannot imaging that the file would be sharp after having its edge burnt off. It would be ok for certain tools, but I will defer to using a wire
wheel to clean my files. |
yes, that is correct when sodium carbonate neutralizes in acid it creates allot of agitation as well as it is an exothermic reaction thus, in my
opinion, it speeds up the rust removal process.
however, using HCL only should also be efficient enough but you still need a basic solution to neutralize the acid on the tool.
|
|
|
Ashot
Hazard to Self
Posts: 79
Registered: 9-7-2016
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by diddi | | I cannot imaging that the file would be sharp after having its edge burnt off. It would be ok for certain tools, but I will defer to using a wire
wheel to clean my files. |
The first comment obviously was addressed to dank
In any case, I agree with you file is not the best tool for such a process but this is all I could find at home.
|
|
|
diddi
National Hazard
Posts: 723
Registered: 23-9-2014
Location: Victoria, Australia
Member Is Offline
Mood: Fluorescent
|
|
yeh the chem is good, but the application you suggested is not ideal. I do woodwork and sometimes incorporate railway dogspikes in my work. I am
going to try it on some dogspikes where fine edge loss is irrelevant.
Beginning construction of periodic table display
|
|
|
Ashot
Hazard to Self
Posts: 79
Registered: 9-7-2016
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by diddi | | yeh the chem is good, but the application you suggested is not ideal. I do woodwork and sometimes incorporate railway dogspikes in my work. I am
going to try it on some dogspikes where fine edge loss is irrelevant. |
I am really curious how efficient it would be on dogspikes. Will you galvanize them after the process?
Would be nice to hear about your results.
|
|
|
diddi
National Hazard
Posts: 723
Registered: 23-9-2014
Location: Victoria, Australia
Member Is Offline
Mood: Fluorescent
|
|
I use polyurethane clear coat over the top, or 2-pack depending in the piece I am doing. galvanising looks shitty and is prone to wear and then rust
later on. I will have a try when I am doing another project
Beginning construction of periodic table display
|
|
|
Texium
|
Thread Moved
23-8-2016 at 08:22 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
