Zandins
Harmless
Posts: 25
Registered: 18-6-2016
Member Is Offline
Mood: No Mood
|
|
Lead nitrate from Pb(OH)2 and Mg(NO3)2 - feasibility
Greetings sciencemadness community,
In order to electroplate a lead dioxide anode, a soluble lead salt, such as lead nitrate, is required. However, I currently do not have access to it.
Instead, I have theorized an alternate method of its synthesis, which goes as follows:
First, lead plate is recovered from an old, scrapped car battery. The plate is washed in NaHCO3 solution and cleaned of any battery-paste. It is then
used as an anode for electrolysis of an indifferent electrolyte at circa 5A current. The plate quickly evolves and forms white flakes and precipitate
in the solution.
1) Am I correct in assuming the precipitate is lead (II) hydroxide?
The white powder would then be washed with distilled water and dissolved in 1L of H20 until saturated ( Wikipedia gives solubility as 15.5 g/L) and
magnesium nitrate would then be added.
Pb(OH)2 + Mg(NO3)2 --> Pb(NO3)2 + Mg(OH)(s)
Magnesium hydroxide is extremely insoluble in water and is expected to precipitate out. Then, the precipitate would be filtered off and a fresh dose
of Pb(OH)2 added, et cetera.
2)What are your thoughts? Is it feasible to actually carry this out?
Zandins
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Zandins  |
The white powder would then be washed with distilled water and dissolved in 1L of H20 until saturated ( Wikipedia gives solubility as 15.5 g/L) and
magnesium nitrate would then be added.
Pb(OH)2 + Mg(NO3)2 --> Pb(NO3)2 + Mg(OH)2(s)
Magnesium hydroxide is extremely insoluble in water and is expected to precipitate out. Then, the precipitate would be filtered off and a fresh dose
of Pb(OH)2 added, et cetera.
|
What matters here are the Solubility products or Ksp values, not the solubility limits.
For Mg(OH)2: Ksp = 1.5 x 10-11 (Wiki)
For Pb(OH)2: Ksp = 1.4 x 10-20 (Wiki)
That means the displacement reaction you propose is simply not possible, because the lead (II) hydroxide is in fact less soluble than the magnesium
hydroxide.
Edit:
This source gives slightly different values for the Ksp values but the lead hydroxide is still about 10000 times less soluble than the
magnesium hydroxide.
[Edited on 18-6-2016 by blogfast25]
|
|
|
DraconicAcid
International Hazard
Posts: 4332
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
If you want a soluble lead salt, then I think your best bet would be to dissolve the hydroxide in nitric or acetic acids.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
Or pechloric acid!
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
DraconicAcid
International Hazard
Posts: 4332
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
I'm assuming the OP has more easy access to acetic acid than perchloric.....
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
Zandins
Harmless
Posts: 25
Registered: 18-6-2016
Member Is Offline
Mood: No Mood
|
|
Point taken
In this case, I think I will heat the Mg(NO3)2 to 330C in a steel crucible to decompose it, and bubble the NO2 through water to make the required
nitric. Anyway, thanks to Blogfast25 for pointing out my misconception.
As for the perchloric, it is one of the principal chemicals for which I require the PbO2 anode in the first place.Although according to my Solubility
Megatable(attached), I can also use chloric, bromic, hexafluorosilicic, formic and acetic acids. Plenty of options.
|
|
|
gsd
National Hazard
Posts: 847
Registered: 18-8-2005
Member Is Offline
Mood: No Mood
|
|
If you have an access to acetic acid and hydrogen peroxide then you can directly form lead acetate from lead metal without going thru' hydroxide
route.
There is a plenty of discussion of this on this forum.
gsd
|
|
|
Jstuyfzand
Hazard to Others
Posts: 166
Registered: 16-1-2016
Location: Netherlands
Member Is Offline
Mood: Learning, Sorta.
|
|
I wonder, if you use Copper and lead acetate, would electroplating in alcohol work? Copper acetate doesnt dissolve in water.
EDIT: Nevermind
[Edited on 19-6-2016 by Jstuyfzand]
|
|
|
j_sum1
Administrator
Posts: 6320
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
I have a strip of lead with a nice stable coating of lead dioxide on it that I use for electrolysis. Granted, I have not been using it for chlorates
or perchlorates so in that sense it is untested. But it could not have been easier to make.
I simply used the strip of lead to electrolyse copper sulfate to make sulfuric acid. After a number of runs the electrode is looking pretty good.
If your target was the electrode rather than the acid you could forget about the copper sulfate solution and simply use H2SO4. The process is
certainly a lot simpler than my attempts to deposit PbO2 on a graphite substrate or to make something from lead dioxide directly.
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
Or formic... 
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by Zandins |
As for the perchloric, it is one of the principal chemicals for which I require the PbO2 anode in the first place.Although according to my Solubility
Megatable(attached), I can also use chloric, bromic, hexafluorosilicic, formic and acetic acids. Plenty of options.
|
Nice table...
What does the P, H, M, - stands for?
I guess...
P --> soluble
H --> unsoluble/precipitate
M --> moderately soluble
"-" --> unstable
HClO4 is M while it should be P...
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
Zandins
Harmless
Posts: 25
Registered: 18-6-2016
Member Is Offline
Mood: No Mood
|
|
Yes, although I do not know the specific limits separating soluble/moderate/insoluble.
The HClO4 puzzles me too, probably a misprint...
As for the original topic, I think I will melt the meshes down into a solid plate and try the sulfuric acid approach. Some sources state the coating
becomes porous and unreliable, but I guess there is only one way to find out.
P.s. Everyone is more than welcome to use the Supertable for their own purposes, if need be.
[Edited on 20-6-2016 by Zandins]
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
An interesting experiment would be to treat aqueous Lead acetate with CO2. Collect the fresh precipitate of PbCO3 and rinse. Then, treat with more
aqueous CO2 with added Copper(ll) nitrate (and not Mg(NO3)2 as Magnesium forms a soluble hydrogen carbonate, but not Copper which appears to form only
a basic copper carbonate).
Logic: Lead(II) carbonate, PbCO3 is prepared industrially from the action of CO2 on a cold dilute lead(II) acetate (warm solutions will form the basic
carbonate per Wikipedia at https://en.m.wikipedia.org/wiki/Lead_carbonate ).
There is a limited increase of the solubility of PbCO3 in aqueous CO2 (see table at http://lead.atomistry.com/lead_carbonate.html ) and the presence of an acidic Cu(NO3)2 may foster the formation of the PbHCO3(+) and with an
excess of CO2 other carbonate complexes (see reference below, Table 3.1). As such, the solubility product hurdle associated with PbCO3 may be
obviated.
I am not expecting a significant effect by CO2 on the copper salts (see, for example, page 15 at https://books.google.com/books?id=ZR8ZAQAAIAAJ&pg=RA2-PA... ).
The role of pH and dissolved inorganic carbon (DIC includes CO2) has been a topic of research in promoting soluble Pb concentration in drinking water.
See, for example, Table 3.1, page 27 available at https://www.google.com/url?sa=t&source=web&rct=j&... .
I can envision three possible results, no Pb(NO3)2, a very limited amount associated with only a small amount of soluble Pb complex formations, or an
acceptable yield.
-----------------------------
One may be able to prepare Cu(NO3)2 by mixing aqueous CuSO4 and 2 KNO3, and freezing out the K2SO4.
[Edited on 21-6-2016 by AJKOER]
|
|
|
DraconicAcid
International Hazard
Posts: 4332
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
| Quote: Originally posted by PHILOU Zrealone |
Nice table...
What does the P, H, M, - stands for?
I guess...
P --> soluble
H --> unsoluble/precipitate
M --> moderately soluble
"-" --> unstable
HClO4 is M while it should be P...
|
It's Russian, soluble = растворимый
insoluble = нерастворимый (the prefix "ne-" is the same as "non-" or "in-").
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
| Quote: Originally posted by Zandins | Yes, although I do not know the specific limits separating soluble/moderate/insoluble.
The HClO4 puzzles me too, probably a misprint...
As for the original topic, I think I will melt the meshes down into a solid plate and try the sulfuric acid approach. Some sources state the coating
becomes porous and unreliable, but I guess there is only one way to find out.
P.s. Everyone is more than welcome to use the Supertable for their own purposes, if need be.
[Edited on 20-6-2016 by Zandins] |
Can you plz also provide the xls(x) file? I'd like the xls(x) format rather than a jpg thx
|
|
|
VSEPR_VOID
National Hazard
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
Whatever you make remember to add it to the List of Chemicals and Materials Made by Sciencemadness.org Users
https://docs.google.com/document/d/1AoI2VA5L4bmFw2HwXS2OVYTV...
Within cells interlinked
Within cells interlinked
Within cells interlinked
|
|
|
yobbo II
National Hazard
Posts: 762
Registered: 28-3-2016
Member Is Offline
Mood: No Mood
|
|
http://www.sciencemadness.org/talk/viewthread.php?tid=5490#p...
Lead salts preparation thread
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
