DoctorOfPhilosophy
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 130
Registered: 12-6-2012
Location: Ontario, Canada
Member Is Offline
Mood: enthralled
|
|
Methyl iodide purification
Just prepared some methyl iodide using the "aluminum foil" method (https://www.youtube.com/watch?v=8zzQVLr1ddo). Any idea if I can purify with sodium bicarbonate? I added a little and it reacts, but I don't know
if it's destroying the MeI. Also Wikipedia says sodium thiosulfate but I don't have it on hand.
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Old school would be to shake it with mercury. But what are you trying to purify from? Do you have yellow/brown coloration? Trying to get rid of
water? Trying to get rid of MeOH? Trying to increase the purity in general?
|
|
UC235
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Methyl iodide doesn't react with bicarbonate solution at any reasonable pace. If it fizzes, you have some HI present from decomposition/solvolysis.
Saturated bicarb (add a tiny bit of sulfite or bisulfite to remove iodine traces) will remove HI and methanol (to an extent)
Concentrated sulfuric acid will remove anything that isn't MeI (but watch out for heating if it's very wet or contains MeOH)
MeI is best stored in a freezer in the dark over copper powder.
|
|
chemplayer...
Legendary
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 191
Registered: 25-4-2016
Location: Away from the secret island
Member Is Offline
Mood: No Mood
|
|
Washing with a little dilute sodium hydrogen sulfite or sodium thiosulfate solution will remove any yellow/brown iodine. If the product is still
coloured after this then you've got some unusual impurity present. Separate off the dense bottom liquid and then re-distill it to get pure methyl
iodide. Keep this in a very well sealed bottle (as UC235 says in the freezer is a good idea) and with a few granules of anhydrous CaCl2 to keep it
dry. Then it's pretty much Grignard ready out of the bottle.
If the product after washing is pure water coloured and you don't mind accepting a slightly lower quality of product, you can then separate and dry at
this stage without re-distilling. If you want to use for a Grignard reaction then best to re-distill though. Depends what your ultimate aim is...
|
|
DoctorOfPhilosophy
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 130
Registered: 12-6-2012
Location: Ontario, Canada
Member Is Offline
Mood: enthralled
|
|
Thanks everyone for your help. That explains why I couldn't get the colour out with bicarb. I'll try thiosulfate, I found some from an old chemistry
set. the colour probably is the iodine.
Chemplayer, your channel rocks!
|
|