Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
 Pages:  1  
Author: Subject: Drying Glycerol
dangerous amateur
Hazard to Others
***




Posts: 148
Registered: 8-7-2011
Member Is Offline

Mood: No Mood

[*] posted on 7-11-2012 at 06:01
Drying Glycerol


Hi,

I've got 60% Glycerol here and like to dry it.

Can it be done just by boiling the water of?
View user's profile View All Posts By User
PHILOU Zrealone
International Hazard
*****




Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline

Mood: Bis-diazo-dinitro-hydroquinonic

[*] posted on 7-11-2012 at 06:25


Should work because glycerol is quite unvolatile.
So simply heat arround 100°c under a flow of air and mixing until 40% weightloss.




PH Z (PHILOU Zrealone)

"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
View user's profile View All Posts By User
bahamuth
Hazard to Others
***




Posts: 384
Registered: 3-11-2009
Location: Norway
Member Is Offline

Mood: Under stimulated

[*] posted on 7-11-2012 at 07:42


I doubt simply boiling off the water will do any good, at least you need to raise the temp and lower the pressure to get any effect without destroying the glycerol. Bubbling hot dry air through a stirred hot solution of glycerol with vigorous stirring under reduced pressure might do the trick.

Glycerol at ~100 degrees Celsius is used to dry ethanol to an anhydrous state, by passing ~95% ethanol/water vapor through the hot glycerol, as not to liquify the ethanol, but only retain the water.

In the lab, anhydrous glycerol is a treasured thing (at least where I work...) and old unopened bottles of the nearly anhydrous stuff (~99.5 and above) is useless and is no longer usable as anhydrous material. Opened containers of the anhydrous glycerol is no longer considered anhydrous and is usually discarded or set to other uses.


Here is some general info I found on glycerol, though I could not find much on the drying of it.
Glycerine - an overview

Let me know if you ever attempt this and if it works, interested in somewhat large scale drying of glycerol myself but never had the incentive to do so.. And hope you succeed.




Any sufficiently advanced technology is indistinguishable from magic.
View user's profile View All Posts By User
ScienceSquirrel
International Hazard
*****




Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline

Mood: Dogs are pets but cats are little furry humans with four feet and self determination! :(

[*] posted on 7-11-2012 at 08:06


Glycerol can be dried by simply heating it above the boiling point of water.
View user's profile View All Posts By User
Nicodem
Super Moderator
*******




Posts: 4230
Registered: 28-12-2004
Member Is Offline

Mood: No Mood

[*] posted on 7-11-2012 at 08:38


Quote: Originally posted by ScienceSquirrel  
Glycerol can be dried by simply heating it above the boiling point of water.

Do you have a reference for this?
It sounds quite counterintuitive, given the partial pressure of water vapors above a 60% glycerol/water mixture at 100 °C is still much lower than the atmospheric pressure. Increasing temperature would bring it to boil, but as the concentration of glycerol raises, so does the partial pressure of water vapors drop. I guess you could perhaps reach >90% concentrations by distilling off part of the mixture under vacuum, but given the strong hygroscopicity, the anhydrous state is unlikely to be achieved by mere concentration. Anyway, I guess those interested in drying glycerol could check the literature on how it is done.




…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)

Read the The ScienceMadness Guidelines!
View user's profile View All Posts By User
kristofvagyok
National Hazard
****




Posts: 659
Registered: 6-4-2012
Location: Europe
Member Is Offline

Mood: No Mood

[*] posted on 7-11-2012 at 10:28


The most practical purification of glycerol according to my memories is:

Add high excess of n-propanol (300cm of 60% glycerol to 1700cm of n-propanol), boil it and collect the evaporated n-propanol water mixture, distill it til you get a little more than 1000cm3 of distillate collected, then place the resulting solution in the freezer for a night. The pure glycerol will crystallize out, filter it on a cooled Büchner (work fast:D) and wash the resulting crystals with chilled acetone or diisopropyl ether.

Distillation on atmospheric pressure won't work.

[Edited on 7-11-2012 by kristofvagyok]




I have a blog where I post my pictures from my work: http://labphoto.tumblr.com/
-Pictures from chemistry, check it out(:

"You can’t become a chemist and expect to live forever."
View user's profile Visit user's homepage View All Posts By User
bahamuth
Hazard to Others
***




Posts: 384
Registered: 3-11-2009
Location: Norway
Member Is Offline

Mood: Under stimulated

[*] posted on 7-11-2012 at 11:10


Quote: Originally posted by kristofvagyok  
The most practical purification of glycerol according to my memories is:

Add high excess of n-propanol (300cm of 60% glycerol to 1700cm of n-propanol), boil it and collect the evaporated n-propanol water mixture, distill it til you get a little more than 1000cm3 of distillate collected, then place the resulting solution in the freezer for a night. The pure glycerol will crystallize out, filter it on a cooled Büchner (work fast:D) and wash the resulting crystals with chilled acetone or diisopropyl ether.

Distillation on atmospheric pressure won't work.


[Edited on 7-11-2012 by kristofvagyok]


Hmm, sounds very expensive and time consuming, regarding that close-to-anhydrous glycerol is relatively cheap...

Though I have found freeze-out-crystallization of simple organics simple and clean (had access to -80 degrees C freezers, Liq. N2 and dry ice), I imagine this to be too labor intensive if not set up as a continuous process, e.g. as part of a semi-large to large ethanol drying setup...


Edit: Found a reference to what you are describing though not perfectly the same, just needed to borrow some keywords from you:P

drying of glycerol by distillation with n-propanol

With the original work here:

Purification of Glycerol by Crystallization H. B. Hass and J. A. Patterson Industrial & Engineering Chemistry 1941 33 (5), 615-616


[Edited on 7-11-2012 by bahamuth]




Any sufficiently advanced technology is indistinguishable from magic.
View user's profile View All Posts By User
kristofvagyok
National Hazard
****




Posts: 659
Registered: 6-4-2012
Location: Europe
Member Is Offline

Mood: No Mood

[*] posted on 7-11-2012 at 11:59


Quote: Originally posted by bahamuth  
Edit: Found a reference to what you are describing though not perfectly the same, just needed to borrow some keywords from you:P

drying of glycerol by distillation with n-propanol

With the original work here:

Purification of Glycerol by Crystallization H. B. Hass and J. A. Patterson Industrial & Engineering Chemistry 1941 33 (5), 615-616

The method what I have described was from the "purification of organic chemicals" second ed., the big white book, one of the most useful books in a lab.

Also, I did wrote the recipe from my memories, because I looked up this a while ago... If something was missing, sorry.




I have a blog where I post my pictures from my work: http://labphoto.tumblr.com/
-Pictures from chemistry, check it out(:

"You can’t become a chemist and expect to live forever."
View user's profile Visit user's homepage View All Posts By User
ScienceSquirrel
International Hazard
*****




Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline

Mood: Dogs are pets but cats are little furry humans with four feet and self determination! :(

[*] posted on 7-11-2012 at 12:55


Quote: Originally posted by Nicodem  
Quote: Originally posted by ScienceSquirrel  
Glycerol can be dried by simply heating it above the boiling point of water.

Do you have a reference for this?
It sounds quite counterintuitive, given the partial pressure of water vapors above a 60% glycerol/water mixture at 100 °C is still much lower than the atmospheric pressure. Increasing temperature would bring it to boil, but as the concentration of glycerol raises, so does the partial pressure of water vapors drop. I guess you could perhaps reach >90% concentrations by distilling off part of the mixture under vacuum, but given the strong hygroscopicity, the anhydrous state is unlikely to be achieved by mere concentration. Anyway, I guess those interested in drying glycerol could check the literature on how it is done.


Will Organic Syntheses do you, see Note3?

Oops I forgot the reference

http://www.orgsyn.org/orgsyn/orgsyn/prepContent.asp?prep=cv1...

[Edited on 7-11-2012 by ScienceSquirrel]
View user's profile View All Posts By User
PHILOU Zrealone
International Hazard
*****




Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline

Mood: Bis-diazo-dinitro-hydroquinonic

[*] posted on 7-11-2012 at 13:22


First what I have written earlier.

Then if anhydrous is needed: In a closed system now!
Molecular sieves, CaCl2, CaO, silicagel, white CuSO4, anhydrous Na2SO4, P2O5 are good dehydrators...
Then vacuum distil.




PH Z (PHILOU Zrealone)

"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
View user's profile View All Posts By User
bahamuth
Hazard to Others
***




Posts: 384
Registered: 3-11-2009
Location: Norway
Member Is Offline

Mood: Under stimulated

[*] posted on 7-11-2012 at 15:11


Quote: Originally posted by PHILOU Zrealone  
First what I have written earlier.

Then if anhydrous is needed: In a closed system now!
Molecular sieves, CaCl2, CaO, silicagel, white CuSO4, anhydrous Na2SO4, P2O5 are good dehydrators...
Then vacuum distil.


I suspect glycerol to have a stronger affinity to water than CaCl2, silica gel and Na2SO4. At least they will not dry the glycerol completely. Though I have no proof of this but scouring the net I find lots of use for glycerol as a moderately strong desiccant in some cases. Molecular sieves would probably work, as would probably anhydrous CuSO4 and CaO. P2O5 will dehydrate your glycerol to acrolein.

Even if the desiccants above will dehydrate the glycerol, they will give their water (or at least some of it) back when the temperature is high enough for the glycerol to distill even under reduced pressures, except CaO though.

In one of my above links; Glycerol - An overview, they state a boiling point of 152 degrees Celsius at 5 mmHg, in which is all but the CaO will give their water back at the reduced pressures, excluding the phosphorous pentoxide.


But of course this whole discussion depends on how dry the OP really needs it; when someone mentions "dry" to me I at least think they mean anhydrous or as close as possible to that.




Any sufficiently advanced technology is indistinguishable from magic.
View user's profile View All Posts By User
ScienceSquirrel
International Hazard
*****




Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline

Mood: Dogs are pets but cats are little furry humans with four feet and self determination! :(

[*] posted on 7-11-2012 at 15:39


For some purposes eg the synthesis of acrolein and nitroglycerine dry could be defined as maybe 98 - 99% or better and that is good enough to give good yields of the desired product.
Very dry would be maybe 99.9 or 99.99%.
Distilling under dry nitrogen in flame dried Schlenk apparatus from molecular sieves might get you close to anhydrous but I guess it would still contain a few molecules of water.
View user's profile View All Posts By User
dangerous amateur
Hazard to Others
***




Posts: 148
Registered: 8-7-2011
Member Is Offline

Mood: No Mood

[*] posted on 10-11-2012 at 04:42


Thank you for your answers.

Well, in fact I'm indeed thinking about some little nitration experiments. I know that it's not necessary to have 99%, but I since I'm very low on acids I do not want to waste it just for absorbing water.
As a matter of principle.

Unfortunately I don't have a destillation apparatus (yet).

But I got another bottle of pure glycerine from a friend. Should have 99%. But as so many other stuff, it came in a plastic bottle;)
Is it worth to be decanted into a proper glass vessel?




View user's profile View All Posts By User
Lambda-Eyde
National Hazard
****




Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline

Mood: Cleaved

[*] posted on 10-11-2012 at 06:36


What's wrong with plastic? I've seen 99% glycerol from Merck in HDPE bottles.



This just in: 95,5 % of the world population lives outside the USA
Please drop by our IRC channel: #sciencemadness @ irc.efnet.org
View user's profile View All Posts By User
dangerous amateur
Hazard to Others
***




Posts: 148
Registered: 8-7-2011
Member Is Offline

Mood: No Mood

[*] posted on 10-11-2012 at 13:06



Quote:

What's wrong with plastic? I've seen 99% glycerol from Merck in HDPE bottles.

Take a look at that nice PDF bahamuth posted, Page nine.

Humidity at my storage place is about 60%.
That means over time it will settle at 75% Now if it's in a glass bottle with proper cap this wont happen, or at least take a very long time.
View user's profile View All Posts By User
kristofvagyok
National Hazard
****




Posts: 659
Registered: 6-4-2012
Location: Europe
Member Is Offline

Mood: No Mood

[*] posted on 10-11-2012 at 13:47


Quote: Originally posted by dangerous amateur  

Take a look at that nice PDF bahamuth posted, Page nine.

Humidity at my storage place is about 60%.
That means over time it will settle at 75% Now if it's in a glass bottle with proper cap this wont happen, or at least take a very long time.

I still don't get it. We've got a LOT chemicals shipped in HPDE bottles and they do not absorb more water than other chems what are kept in glass.

Why would the be glycerine unpure if it is stored in a 60% humidity room in a HDPE bottle? If is closed well, then you can keep it in the HDPE flask under water also.




I have a blog where I post my pictures from my work: http://labphoto.tumblr.com/
-Pictures from chemistry, check it out(:

"You can’t become a chemist and expect to live forever."
View user's profile Visit user's homepage View All Posts By User
thejerseyrebel
Harmless
*




Posts: 1
Registered: 18-11-2015
Member Is Offline

Mood: No Mood

[*] posted on 23-1-2016 at 15:50


so I tried this with some impure glycerin with cacl2 but when I transferred it to another container with cacl2 I saw hydrochloric acid fumes pouring out with the molten glycerin. I have absolutely no idea why the road salt grade cacl2 reacted though the glycerin is quite contaminated and needs to be decolorized
View user's profile View All Posts By User
MeshPL
Hazard to Others
***




Posts: 329
Registered: 20-4-2015
Location: Universe
Member Is Offline

Mood: No Mood

[*] posted on 27-1-2016 at 02:24


Molecular sieves should work, they are quite a powerful dessicant. Although a huge excess will be required to overcome glycerol's affinity to water. Silica gel could work. It should be noted that due to simmilarity of glycerol to water most dessicants will dissolve e.g. sodium sulphate, calcium chloride, copper sulphate... basic and acidic dessicants may simply dissolve.
View user's profile View All Posts By User
Praxichys
International Hazard
*****




Posts: 1063
Registered: 31-7-2013
Location: Detroit, Michigan, USA
Member Is Offline

Mood: Coprecipitated

[*] posted on 27-1-2016 at 05:48


Bubbling dry air through the glycerol solution with progressive warming would work well. You would have to stop below the temperature where decomposition becomes rapid, so something less than 280°C. It could then be vacuum fractionated from its decomposition/oxidation products. Oxidation could be significant enough to warrant the use of an inert gas rather than air, and would undoubtedly result in a purer product.

Azeotropic drying using toluene and a dean-stark trap might work but would probably be slow since this relies on the partial pressure of water in glycerol at only 110°C.

I would be hesitant to use solid desiccants because glycerol is quite viscous and will be difficult to filter from fine solids. Further, if the desiccant works well enough the glycerol could solidify. Besides, it is not practical to remove 40% water using solid desiccants. Even 5% would be quite high for something like that.




View user's profile Visit user's homepage View All Posts By User
S.C. Wack
bibliomaster
*****




Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline

Mood: Enhanced

[*] posted on 27-1-2016 at 09:09


Quote: Originally posted by thejerseyrebel  
so I tried this with some impure glycerin with cacl2 but when I transferred it to another container with cacl2 I saw hydrochloric acid fumes pouring out with the molten glycerin.


If one is going to try calcium chloride drying of glycerol, it'll be in a vacuum desiccator with a separate container for each. Perhaps you've made an addition compound that would be expected with an -ol. There would some old literature on that out there for the finding for sure if someone cared.

The IEC article mentioned years ago is definitely worth posting somewhere, so here it is.

Attachment: iec_33_615_1941.pdf (261kB)
This file has been downloaded 737 times





"You're going to be all right, kid...Everything's under control." Yossarian, to Snowden
View user's profile Visit user's homepage View All Posts By User
UC235
National Hazard
****




Posts: 565
Registered: 28-12-2014
Member Is Offline

Mood: No Mood

[*] posted on 27-1-2016 at 09:24


It will be much harder to dry glycerol than to just go buy some that is already dry. Unless you're trying to work up biodiesel waste for some reason, you can buy it in bulk for $2/kg.
View user's profile View All Posts By User
MeshPL
Hazard to Others
***




Posts: 329
Registered: 20-4-2015
Location: Universe
Member Is Offline

Mood: No Mood

[*] posted on 28-1-2016 at 02:09


What about making some magnesium methoxide? (by simply boiling magnesium in methanol) And adding it to glycerol so that magnesium hydroxide and methanol are formed. Magnesium hydroxide could be filtered and methanol evaporated.
View user's profile View All Posts By User
kecskesajt
Hazard to Others
***




Posts: 299
Registered: 7-12-2014
Location: Hungary
Member Is Offline

Mood: No Mood

[*] posted on 30-1-2016 at 01:40


I tried evaporating water and ended up in a fog in the kitchen where I can't even see the clock in the other side of the room :D
View user's profile View All Posts By User
Detonationology
Hazard to Others
***




Posts: 362
Registered: 5-5-2015
Location: Deep South
Member Is Offline

Mood: Electrophillic

[*] posted on 30-1-2016 at 09:25


Sounds like you boiled the glycerol.



“There are no differences but differences of degree between different degrees of difference and no difference.” ― William James
View user's profile View All Posts By User
bluamine
Hazard to Others
***




Posts: 197
Registered: 17-8-2015
Member Is Offline

Mood: No Mood

[*] posted on 2-2-2016 at 07:52


Can we use any drying agents to do so? (Like calcium oxide)
View user's profile View All Posts By User
 Pages:  1  

  Go To Top