numos
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 269
Registered: 22-2-2014
Location: Pasadena
Member Is Offline
Mood: No Mood
|
|
Collidine vs Pyridine
I am nearly done with my Rubrene synthesis, and have just finished recrystallizing a nice crop of triarylpropargyl alcohol, synthesis found here:
http://www.sciencemadness.org/talk/viewthread.php?tid=23112
The next step requires chlorination with Thionyl chloride, and although I have some, it was brought to my attention that this route sucks and is prone
to crystallization problems.
plastics provided this method which should be much more reliable:
Quote: Originally posted by plastics ![](images/xpblue/lastpost.gif) |
Synthesis of rubrene from 1,1,3 triphenylprop-2-yn-1-ol
1,1,3-triphenylprop-2-yn-1-ol 2g 4g 6g 8g 10g
Dichloromethane (39.4 °C) 15ml 30ml 45ml 60ml 75ml
Triethylamine 1.1ml 2.2ml 3.3ml 4.4ml 5.5ml
Methanesulphonyl chloride (161 °C) 1.2ml 2.4ml 3.6ml 4.8ml 6.0ml
Collidine (171 – 172 °C) 1ml 2ml 3ml 4ml 5ml
Xylene (140 °C)
2.0 g 1,1,3-triphenylprop-2-yn-1-ol is dissolved in 15 ml anhydrous dichloromethane under nitrogen and cooled to 0 °C
1.1 ml anhydrous triethylamine and 1.2ml methanesulphonyl chloride were added and the mixture stirred for 1 hour at 0 °C, then allowed to warm to
room temperature
The mixture was heated at reflux to distil off the dichloromethane which was gradually replaced with xylene
The solution was heated and on reaching 80 °C 1ml collidine added dropwise
Reaction temperature raised to 95 °C and held at this temperature for 7 hours
Mixture allowed to cool to room temperature and the precipitate collected by filtration
The red soldid was recrystallized from ethanol to afford the desired product yield 0.76 g (46%)
|
Paper found here:
http://www.sciencemadness.org/talk/files.php?pid=430392&...
Everything is good, except I don't have Collidine. I don't want to drop $50+ on Sigma Aldrich, and I haven't found an easy synthesis of Collidine. I
read the article above, but either I missed something, or I don't have the required background to understand what's happening. (Likely the latter)
Can someone please explain the mechanism behind this reaction, specifically the role of Collidine. Collidine refers to a variety of trimethylpyridines
and I'm curious because it is rather similar to Pyridine, and I'm hoping to be able to substitute it.
|
|
byko3y
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 721
Registered: 16-3-2015
Member Is Offline
Mood: dooM
|
|
Collidine here is a 2,x,6-pyridine, and it plays a role on non-nucleophilic base for condensation reaction. Pyridine won't work for that.
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
2,6-Lutidine might work as a drop-in replacement.
|
|
chemrox
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
which collidine? or do you care?
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
UC235
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
If you have some ethyl acetoacetate, you can make a 2,6-dimethylpyridine via Hantzsch pyridine synthesis.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Collidine is most often referring to the 2, 4, 6 compound, if not specified. I would think based on the prep, that 2,6-dimethylpyridine would work
OK, and maybe even pyridine, there might be some change, but I don't see anything that discusses the role of the collidine other than as a
non-reactive base, and thus substitution might well work. The generic scheme just says base in that step. I have even substituted DMAP for
pyridine and other pyridine bases in many cases with equal or better yields, since it is not nearly as smelly as pyridine, and is more basic, but in
this case, I would not try that to start with.
|
|
byko3y
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 721
Registered: 16-3-2015
Member Is Offline
Mood: dooM
|
|
Dr.Bob, DMAP is more similar to pyridine than collidine/lutidine is. E.g. Dakin-West reaction gives lower yields when using pyridine as acylation
catalyst.
Although, the OP's reaction is performed using tertiary alkyl halide, which is a weak alkylation agent by itself, so pyridine might work there, but I
don't know whether there are no other possible electrophilic alkylators. Or probably reaction needs a protected pyridine ring, otherwise cyclization
will happen.
|
|
numos
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 269
Registered: 22-2-2014
Location: Pasadena
Member Is Offline
Mood: No Mood
|
|
This is what I was hoping for
Quote: Originally posted by Dr.Bob ![](images/xpblue/lastpost.gif) | I don't see anything that discusses the role of the collidine other than as a non-reactive base, and thus substitution might well work. The generic
scheme just says base in that step. |
This is what I was afraid of
It wouldn't even be a problem, I could just test it, but I have enough of the triphenyl propargyl alcohol to do one run.
The procedure only says "collidine" not specifying which isomer, so I'm hoping that's simply what they had on hand, or was easier to use. Judging from
the responses, it seems the collidine is not a direct reactant (that sounds so incorrect, sorry) and pyridine would have the same affect, but in
addition may influence the reaction negatively - so it will still work but I should expect my yield to take a hit?
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by numos ![](images/xpblue/lastpost.gif) |
It wouldn't even be a problem, I could just test it, but I have enough of the triphenyl propargyl alcohol to do one run.
|
When you say one run, you mean on 2 g scale following the procedure Plastics had provided? Why not test the reaction on 50 to 100 mg scale...then if
it works you can scale up, and if it doesn't then you've not burned all your material and can trial several other conditions.
|
|
DrMethyl
Harmless
Posts: 34
Registered: 23-11-2015
Member Is Offline
Mood: No Mood
|
|
hello, I've used collidine to trap methyl iodide. Collidine is more basic and nucleophile because of the electron-releasing alkyl group.
I don't know this reaction but maybe it can be replaced by something like DBU (?)
|
|