Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
red lead (2PbO*PbO2)
I recently made this compound, also sometimes designated Pb3O4, using PbO. About 4g was placed on an inverted ceramic lid in a muffle furnace. This
was heated for 6 hours at 465±10°C. About every half hour I would turn the powder with a spatula. The temperature range shown in Wiki was
450-480°C, the rest of the procedure was based on that found in"Synthetic Inorganic Chemistry," p.281, by Blanchard et al in the forum
library.
The color changes indicated in Blanchard occured as described. But there was no weight increase. From this equation I calculated that there should
be about a 2% weight increase:
3PbO + 1/2O2 --> 2PbO*PbO2
The final product is shown below.
Has anyone else made red lead? If so, what was your experience?
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
Neat prep, Magpie! What is the precision/accuracy of your weighing (I know, "massing", BUT I'm too old to change my habits)? 2% of 4g is only 80 mg,
and I wonder if there were other losses (spattering?) to account for no gain in weight. I'm just starting to set up a lab after 35 years of no
chemistry activity, so I've got a lot to learn (and re-learn!).  CharlieA
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
I used my gun powder scale which weighs down to 0.1 grain (7mg). The wt increase was only 0.1 grain, or 7 mg.
The color change was interesting in that the orange PbO went to a dark brown right away on heating. On cooling it changed to red. What you see in
the photo is fairly close.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
Kagutsuchi
Hazard to Self
Posts: 51
Registered: 21-6-2015
Location: Hungary
Member Is Offline
Mood: Happy
|
|
I am planning to perform it, too, but I must be really careful because my PbO is contamined withquite a lot of Pb(NO3)2, so I must heat it before the
experiment.
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
If there was 2% water (and maybe CO2) absorbed in the PbO then there would be no overall change in mass.
|
|
|
gsd
National Hazard
Posts: 847
Registered: 18-8-2005
Member Is Offline
Mood: No Mood
|
|
Hi Magpie! Nice preparation.
Just a thought, for 3 mole of PbO, it needs 1 atom of O for this reaction as your equation shows.
Hence Oxygen (O) required is 4*16/(3*223.2) = 0.09558gm = 1.08 lit of O2 @ NTP. Which corresponds to 1.08/0.21 = 5.1 lit of air.
Now your temperature was 465 Deg C avg. which corresponds to required air volume of 5.1*(273+465)/273=13.8 lit. This much air is required if you have
a perfect mixing. Barring some "turning over" in-between, yours was a stagnant system.
Are you sure enough Oxygen was contacted with your PbO?. Normally this types of preparations are done in a flow system.
gsd
[Edited on 11-10-2015 by gsd]
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Hi gsd. I only used about 4g of PbO. Also, every half hour I was opening the furnace and stirring the powder. So I think it was getting enough
oxygen.
Unionised's hypothesis is more likely correct. For cooling the hot red lead I placed it in a dessicator. What I should have done was dry the PbO at
120°C or so before weighing and firing.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
Squall181
Harmless
Posts: 46
Registered: 21-2-2011
Member Is Offline
Mood: No Mood
|
|
I've attempted to make red lead in the past and had some success, but my only real test at the time was using it to make some crackling stars. I used
my hot plate to heat lead carbonate with constant agitation until it turned red.
Here's a video of the whole process if anyone is interested.
https://youtu.be/hJPQcmwrBhE
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
