wireshark
Harmless
Posts: 28
Registered: 21-1-2013
Member Is Offline
Mood: No Mood
|
|
Hydrogen chloride gas balloon
I know hydrogen balloons are a regular thing used in labs. But what about HCl? I want to make hydrochloric acid and I don't have very much equipment
at the moment for a proper generator/bubbler apparatus.
So how about filling a balloon with HCl (stoichiometric amount), putting it over a flask with water (stoichiometric amount) and a stirbar, and then
letting it go for a day or so. All done outside. Is this safe? Would it work?
|
|
|
kristofvagyok
National Hazard
Posts: 659
Registered: 6-4-2012
Location: Europe
Member Is Offline
Mood: No Mood
|
|
Yes, yes.
Just don't breathe it in.
I have a blog where I post my pictures from my work: http://labphoto.tumblr.com/
-Pictures from chemistry, check it out(:
"You can’t become a chemist and expect to live forever." |
|
|
zed
International Hazard
Posts: 2284
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
No, no, no. Buy, or make, better equipment.
Also, are you assuming that a common balloon will be resistant to HCl gas?
|
|
|
ScienceSquirrel
International Hazard
Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline
Mood: Dogs are pets but cats are little furry humans with four feet and self determination! 
|
|
Hydrogen chloride is very soluble in water so even a small amount might result in rapid deflation as the gas reacts to form hydrochloric acid.
If you connect a balloon filled with hydrogen chloride to a flask containing water it will deflate almost instantly.
|
|
|
wireshark
Harmless
Posts: 28
Registered: 21-1-2013
Member Is Offline
Mood: No Mood
|
|
| Quote: | Hydrogen chloride is very soluble in water so even a small amount might result in rapid deflation as the gas reacts to form hydrochloric acid.
If you connect a balloon filled with hydrogen chloride to a flask containing water it will deflate almost instantly. |
All right, what's wrong with that? Will the acid shoot back up into the balloon because of the pressure difference? If so, I could pinch it off before
the balloon deflates.
| Quote: | No, no, no. Buy, or make, better equipment.
Also, are you assuming that a common balloon will be resistant to HCl gas? |
It's not like I'd use the same balloon more than one or two times. Let's say the balloon is made of polyethylene or polystyrene--there's no alkene to
attack. What'd happen anyway?
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
Simple enough to just test it out, and stop postulating.
Go outside on a slightly breezy day. Don some goggles and maybe some gloves or apron if your paranoid. Put some salt into the bottom of a flask, add
a bit of H2SO4 and cap it with the balloon. Once the balloon is filled (if it doesnt damage and pop) take it off, and transfer it to the top of a
flask filled with chilled, stirred water. The HCl will be desolved fast and the bolloon will likely deflate fast, as SS mentioned. This is no problem,
and could probably make a good demo of gasses dissolving in water.
Seems like a safe, easy, and cheap experiment. Just don't deeply inhale and whiff it or dump it in your eyes and you should be fine. Get to it! 
EDIT: Just place a small HCl generator and a wide mouthed container of ice water into a tupperware contianer. The cold water will absorb much of the
released HCl pretty quickly. Just let it sot overnight, and then titrate the newly formed HCl(aq) to get a concentration. then record data and
manipulate variables to optimize your proceedure.
Or rig a gas gen, piping, a suckback trap, inverted funnel, and cold water filled reciever. I think you may be over complicating how to throw this
together. Easy peasy.
[Edited on 20-3-2013 by Bot0nist]
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
bananaman
Harmless
Posts: 19
Registered: 29-1-2013
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by wireshark  | I know hydrogen balloons are a regular thing used in labs. But what about HCl? I want to make hydrochloric acid and I don't have very much equipment
at the moment for a proper generator/bubbler apparatus.
So how about filling a balloon with HCl (stoichiometric amount), putting it over a flask with water (stoichiometric amount) and a stirbar, and then
letting it go for a day or so. All done outside. Is this safe? Would it work? |
Add concentrated sulfuric acid to NaCl to get HCl......
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Better is H2 (non-toxic, non-corrosive, does not react with water, easy to prepare and a lighter gas).
Downsize, if mixed with air and ignited, will explode. Also, the H2 is very probe to escape from sealed containers.
[Edited on 21-3-2013 by AJKOER]
|
|
|
vmelkon
National Hazard
Posts: 669
Registered: 25-11-2011
Location: Canada
Member Is Offline
Mood: autoerotic asphyxiation
|
|
I remember seeing a youtube video.
They fill a long graduated cylinder with chlorine. The chlorine comes from a cylinder.
They also have a hydrogen cylinder. They light up the hydrogen to have a large ongoing flame. They insert it into the chlorine. It burns in the
chlorine but with a pinkish color.
Then, they put the graduated cylinder in water and boom, the water gushes up. Sort like the ammonia fountain experiment.
|
|
|
Adas
National Hazard
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
I would also need HCl in a balloon, but it seems to me that the sulfuric refuses to react with NaCl. I mean, it does, but vast majority of the NaCl
refuses to dissolve (in 37% H2SO4) and there is virtually no gas escape even upon heating. How the heck should I do that?
Rest In Pieces!
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Adas | | I would also need HCl in a balloon, but it seems to me that the sulfuric refuses to react with NaCl. I mean, it does, but vast majority of the NaCl
refuses to dissolve (in 37% H2SO4) and there is virtually no gas escape even upon heating. How the heck should I do that? |
Only concentrated H2SO4 (98 % or better) will displace the HCl.
HCl and H2SO4 are both very strong acids.
In NaCl(s) + H2SO4(l, >98 %) < === > NaHSO4(s) + HCl(g) the reaction equilibrium is pushed to the right because of the escaping HCl gas.
Fusing NaCl with NaHSO4 (sodium bisulphate, pool supplies) should also work but requires heat:
NaCl + NaHSO4 === > Na2SO4 + HCl(g)
There are plenty of HCl generator experiments on this forum. Search and yee shall findeth.
[Edited on 9-6-2015 by blogfast25]
|
|
|
Adas
National Hazard
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
Oh, I have plenty NaHSO4. I might try that, thanks for your helpful response.  I
hope they will melt together as expected.
Rest In Pieces!
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Adas | | Oh, I have plenty NaHSO4. I might try that, thanks for your helpful response. I
hope they will melt together as expected. |
Anhydrous would be best. Tell the difference from the monohydrate by its MP. Mix the salts intimately, using an excess of NaCl (it prevents the
bisulphate from fuming off small amounts of SO3)
|
|
|
Mesa
Hazard to Others
Posts: 264
Registered: 2-7-2013
Member Is Offline
Mood: No Mood
|
|
So, to summarize... You decided to fill a balloon with hydrogen chloride gas because you aren't comfortable/equipped to use the lab technique, but
running a thermal decomposition reaction so hot that it is generally done with a blowtorch or related gas powered flame, that's a piece of cake?
Cool.
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
Well, back to answer the OP.
Yes, it would work if it were absolutely necessary, and there were no other possibilities.
Stick the reagents in the balloon itself (small quantity only - do the maths).
Seal the neck of the balloon onto the test tube, or whatever holds the water.
Have the whole thing in a plastic tray, such as the bottom cut off a 5 Litre plastic milk jug (in case the balloon bursts) and the entire operation
must done Outside.
With HCl a stirbar will not make much difference.
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
The balloon will fall to the ground...
HCl weights 36.5g/mole thus as a gas 36.5g/22.41 Liter
O2 weights 32g/mol --> 32g/22.41L
N2 weights 28g/mol --> 28g/22.41L
Air is 1/5 O2 and 4/5 N2 --> 32/5+28*4/5 = 28.8g/22.41L
So HCl gas is denser than air, with the extra weight of the balloon --> fast landing.
The rubber of the balloon will not stand long HCl especially if there is some humidity in the air.
[Edited on 11-6-2015 by PHILOU Zrealone]
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
It wouldn't HAVE to be made of latex rubber: an inflatable beach ball (pPVC, I think) would resist even wet HCl quite well.
|
|
|
Adas
National Hazard
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
The method with NaHSO4 and NaCl works quite well when you don't need massive amounts. I used a teflon tube which I glued to the piece of balloon that
has a hole in it.. to make it airtight. It's okay but the glue I've used falls apart very quickly. Already ordered some sillicon stoppers with holes,
I hope they could withstand that.
Rest In Pieces!
|
|
|
Adas
National Hazard
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
Also, is there any chance this could work with bromides too? Or is NaHSO4 not acidic enough for that? Would bromides eat silicone stoppers?
Rest In Pieces!
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
If you have the ability to generate bromine gas, try it out and then tell us what happens.
Simple stoichemitry and ideal gas law will allow you to calculate the volume of gas you produce to keep it at a safe level.
Work out the maths along woth the testing procedure you propose and then post your calculations here.
People will check them for you.
You'll get more help here if you actually do some work for yourself.
|
|
|
Adas
National Hazard
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
I don't get it. I'm not even talking about bromine, but HBr gas. I don't know how to calculate whether NaHSO4 and NaBr would react well.
Even if there are some pKa values available, this is of little practical importance as chemistry is really weird sometimes (most of the time). I
merely expected someone with actual practical experience to respond to my post.
Also I don't have NaBr to test this myself, and serious information about silicone resistance to HBr can not be found online. I've just found one
paper that states that hydrogen chloride gas does the same damage to it as methane. Yes, METHANE. And it didn't say "no damage", it was more like
"pretty serious damage". Definitely unreliable.
Rest In Pieces!
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
