Blackrabbit
Harmless
Posts: 1
Registered: 25-2-2015
Member Is Offline
Mood: No Mood
|
|
Addition of Hydrogen Gas to Diesel Combustion.
Hi, Could anyone tell me the outcome of adding Hydrogen Gas to the combustion process in a diesel engine using High Sulphur Content fuel. As in the
normal combustion process with these fuels, Sulphurous and or Sulphuric Acid is formed, would the addition of H2 actually increase the amounts of
these acids formed, causing accelerated wear on the cylinder liners etc.
Thank - you, Blackrabbit.
|
|
|
j_sum1
Administrator
Posts: 6324
Registered: 4-10-2014
Location: At home
Member Is Online
Mood: Most of the ducks are in a row
|
|
How do you propose to add H2? It is difficult stuff to contain. Are you going to attempt to add it to the fuel? Add it to the air mix? Have a
separate feed into the cylinder? I think these issues need to be clarified before you can get a definitive response.
|
|
|
clearly_not_atara
International Hazard
Posts: 2789
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
http://en.wikipedia.org/wiki/Hydrogen_embrittlement
Even if you're the most brilliant engineer in history and find a way to inject H2 into your engine, it'll be broken before the end of the day. Sorry.
|
|
|
Bert
|
Thread Moved
25-2-2015 at 21:13 |
Bert
Super Administrator
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
Inject propane if you feel the need to boost output from a diesel.
http://www.dieselperformanceproducts.com/faq.html
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
|
Loptr
International Hazard
Posts: 1348
Registered: 20-5-2014
Location: USA
Member Is Offline
Mood: Grateful
|
|
This sounds similar to the HHO cells that people sell to create a hydrogen-oxygen mixture from water (it's a scam by the way) that is led into the
intake of the engine.
In the end, any performance you gain will come from messing with the emissions sensors, and will only cause your engine to run rich, which is not good
for the engine.
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
First, some extracts from Wikipedia on Diesel (http://en.m.wikipedia.org/wiki/Diesel_fuel ):
"Diesel engines have found broad use as a result of higher thermodynamic and thus fuel efficiencies. This is particularly noted where diesel engines
are run at part-load; as their air supply is not throttled as in a petrol engine, their efficiency still remains high."...
"Fatty-acid methyl ester (FAME), more widely known as biodiesel,"....
"Fuel equipment manufacturers (FIE) have raised several concerns regarding FAME fuels: free methanol, dissolved and free water, free glycerin, mono
and diglycerides, free fatty acids, total solid impurity levels, alkaline metal compounds in solution and oxidation and thermal stability. They have
also identified FAME as being the cause of the following problems: corrosion of fuel injection components, low-pressure fuel system blockage,
increased dilution and polymerization of engine sump oil, pump seizures due to high fuel viscosity at low temperature, increased injection pressure,
elastomeric seal failures and fuel injector spray blockage.[16]"
Now, my speculation is adding H2 to a mix with the same O2 content adds more water vapor (by consuming some of the oxygen) and reduces the formation
of SOx gases and associated acids, which would otherwise neutralize the likes of NaOH that when hot, readily attacks fuel injection components and
such.
So, I would guess possibly some performance gain from the hydrogen with an engine running hotter, and also more equipment failure issues, especially
in the presence of biodesel.
[Edited on 27-2-2015 by AJKOER]
|
|
|
Zombie
Forum Hillbilly
Posts: 1700
Registered: 13-1-2015
Location: Florida PanHandle
Member Is Offline
Mood: I just don't know...
|
|
Stop over complicating things...
Old school water injection systems still make plenty of power due to increased combustion pressure, and they are completely safe.
There are plenty of kits on the net, and most will have the option of water or Methanol or both.
I've run these set ups in gas, and diesel engines, and while never done any Dyno testing I do have hundreds of 1/4 mile track hours.
Increased cylinder pressure, and reduced combustion temp. = power. Period!
Quote Wiki:
"In internal combustion engines, water injection, also known as anti-detonant injection (ADI), is spraying water into the incoming air or fuel-air
mixture, or directly into the cylinder, in order to cool certain parts of the induction system where "hot points" could produce premature ignition .
It was used historically to increase the power output of military aviation engines for short durations such as dogfights or takeoff, however it has
also been used in motor sport and notably in drag racing. In Otto cycle engines the cooling effects of water injection also allow for greater
compression ratios by reducing the problem of engine knocking (detonation).
http://en.wikipedia.org/wiki/Water_injection_%28engine%29
http://www.dieselarmy.com/engine-tech/how-it-works/how-it-wo...
http://www.coolingmist.com/pagedisplay.aspx?feature_key=dies...
They tried to have me "put to sleep" so I came back to return the favor.
Zom.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Loptr  | This sounds similar to the HHO cells that people sell to create a hydrogen-oxygen mixture from water (it's a scam by the way) that is led into the
intake of the engine.
|
It's only similar if one claims the hydrogen/oxygen mixture is generated inline ('jam jar' style electrolysis scams) and saves fuel. It does the
opposite although with a 'good' [cough!] HHO kit you'll lose little.
|
|
|
deltaH
Dangerous source of unreferenced speculation
Posts: 1663
Registered: 30-9-2013
Location: South Africa
Member Is Offline
Mood: Heavily protonated
|
|
Hydrogen's energy density is pretty pathetic (how far a fixed size tank will get you), as fuels go. It's not easy to store in significant amounts and
insignificant amounts are unlikely to have much effect on your engine.
If your diesel engine has a catalytic converter to reduce NOx emissions (which most do), then anhydrous liquid ammonia from a cylinder might be a good
option.
The calorific content of ammonia is not that great, but it does burn to just water and N2 (post catalytic converter of course). 
[Edited on 27-2-2015 by deltaH]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
