gatewaycityca
Harmless
Posts: 27
Registered: 8-2-2014
Member Is Offline
Mood: No Mood
|
|
Reactions that release nitrogen gas (or other relatively "safe" inert gasses)?
Hi guys, I haven't been on here in quite a while. But I have another newbie question. I built a kind of simple little turbine "engine" which uses
air pressure to spin a turbine wheel. It drives a small DC motor, working as a generator, with reduction gears. It does work, and it does generate
a tiny bit of electricity. (About 1 volt at most! LOL) I had planned to use C02 to drive the turbine, with a simple vinegar and baking soda
reaction. But I was curious, are there are chemical reactions I could use that would release another gas that would be safe to play around with? I
was thinking about oxygen by combining bleach and peroxide, but I'm a little hesitant about that. Then I was thinking about nitrogen, since from what
I understand, it's fairly inert.
I'm looking for something where I can easily combine two substances (preferably liquids if possible), which releases a gas that will be stored in a
bottle, balloons, etc and mildly pressurized. Just enough pressure to spin the turbine.
By the way, here is the "engine" I made. I took the turbine wheel from a mattress inflator I took apart. Please don't laugh! ![:)](./images/smilies/smile.gif)
|
|
Molecular Manipulations
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 447
Registered: 17-12-2014
Location: The Garden of Eden
Member Is Offline
Mood: High on forbidden fruit
|
|
Carbon dioxide is about as safe as it gets. Unless you plan on making tons of it with no ventilation you'll be just fine. Oxygen would be a much
bigger hazard. Nitrogen isn't very easy to isolate quickly, an ammonium salt and a nitrite salt in solution will produce some in hot water, but it's
not that fast.
-The manipulator
We are all here on earth to help others; what on earth the others are here for I don't know. -W. H. Auden
|
|
Mailinmypocket
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1351
Registered: 12-5-2011
Member Is Offline
Mood: No Mood
|
|
No heating required and easy to control, dilute sodium nitrite onto sulfamic acid.
http://mattson.creighton.edu/N2/index.html
Note to self: Tare the damned flask.
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6269
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
I agree. CO2 is probably the best and easiest for what you are trying to do.
I opened this thread because I like the idea of being able to produce gases at need. I don't have a method for making N2. In the spirit of sharing
the love I offer the following:
Cl2 -- HCl and TCCA
O2 -- decomposition of hypochlorite bleach using cobalt chloride catalyst
CO2 -- obvious, carbonate and acid
Argon -- burp a light bulb under water into a zip-seal plastic bag. (Obviously you need to choose your bulb carefully. Many have other gases as
well.)
He -- who needed that party balloon anyway?
N2 -- anyone have a different method? I currently have no nitrites nor sulfamic acid.
|
|
Darkstar
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 279
Registered: 23-11-2014
Member Is Offline
Mood: Sleepy
|
|
Quote: Originally posted by j_sum1 ![](images/xpblue/lastpost.gif) | In the spirit of sharing the love I offer the following:
Cl2 -- HCl and TCCA
O2 -- decomposition of hypochlorite bleach using cobalt chloride catalyst
CO2 -- obvious, carbonate and acid
Argon -- burp a light bulb under water into a zip-seal plastic bag. (Obviously you need to choose your bulb carefully. Many have other gases as
well.)
He -- who needed that party balloon anyway?
|
Don't forget NH3 from ammonium salts and strong bases like NaOH. The nice thing about this method is that it's self-sustaining in the sense
that it generates its own water to keep the reaction going, which means you don't need to continuously drip something into/onto something else for a
steady stream of gas. Just mix the two solids together and add a little water to get it going.
Ammonia is probably not the best gas for what the OP has in mind, but I figured I'd mention it anyway.
|
|
sparkgap
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1234
Registered: 16-1-2005
Location: not where you think
Member Is Offline
Mood: chaotropic
|
|
Quote: | I don't have a method for making N2. |
You could do what airbags do and heat sodium azide. The nitrogen is certainly inert, but sodium azide is not a walk in the park. I'd stick with the
carbon dioxide myself.
sparky (~_~)
"What's UTFSE? I keep hearing about it, but I can't be arsed to search for the answer..."
|
|
gatewaycityca
Harmless
Posts: 27
Registered: 8-2-2014
Member Is Offline
Mood: No Mood
|
|
Thanks everyone for the advice so far. I like the idea of sodium nitrite and sulfamic acid, but where would I even find them? I've never even heard
of sulfamic acid. (Edit: I just did a quick search on Google, and apparently it is used to clean bricks and tiles, and Home Depot has it). But what
about the sodium nitrate?
I probably will stick to CO2 for now. I have a bigger turbine from some kind of ventilation fan. I was planning to take it apart later on and
experiment with a larger engine that could actually do something useful. I wonder how much pressure you could reasonably expect to get from baking
soda and vinegar? I mean, if I had a system where it was flowing through tubes into a mixing tank of some kind by gravity feed, I wonder how much
pressure I could get without having to use ridiculous amounts of vinegar. The resulting C02 would fill a small bottle or tank through another tube
and a one-way valve. I'd use another tube and control valve to vent the pressure and spin the turbine.
I'm hoping to be able to use something similar with mixing other chemicals to use nitrogen.
Of course, all this sounds good...but I have no idea if it would actually work or be practical. So far, the little experiments I've done with the
small turbine I have did work. But that's on a very small scale.
[Edited on 2-22-2015 by gatewaycityca]
[Edited on 2-22-2015 by gatewaycityca]
|
|
Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
If all you want is to turn turbine blades, why not use compressed AIR? Cheap, easily available. No wastes to dispose of.
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
gatewaycityca
Harmless
Posts: 27
Registered: 8-2-2014
Member Is Offline
Mood: No Mood
|
|
Bert, I wanted to make an "engine" where you just add the chemicals and it generates its own mechanical power from the reaction.
|
|
Bot0nist
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
I saw a Mythbusters episode long ago where they attempted to built and operate an engine powered by black powder. The end determination was that
black powder and even other faster pyro mixes contain much less usable energy per tablespoon than gasoline or diesel combusting with air. I imagine
the same is true for other, slower gas generating reactions.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
Make up a mixture of DRY baking soda and cream of tartar (Potassium Hydrogen tartrate) from the grocery store. Place in your "fuel tank". When you
want to start , just add water...
[Edited on 22-2-2015 by Bert]
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
XeF<sub>2</sub> and aqueous base for Xe gas ![;)](./images/smilies/wink.gif)
Aqueous azide plus ceric ammonium nitrate for nitrogen gas.
Oxygen by hydrogen peroxide and manganese dioxide. Higher strength hydrogen peroxide from beauty supply stores and manganese dioxide from batteries.
Used to use this to fill welding tanks, makes high pressures reliably.
Steam.
|
|