Pages:
1
2
3
4 |
Hennig Brand
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1284
Registered: 7-6-2009
Member Is Offline
Mood: No Mood
|
|
Here is a how I have been storing iodine. Small, 50mL, Erlenmeyer flasks were fitted with homemade Teflon stoppers. Teflon rod was chosen that was at
least slightly larger than the inside diameter of the flask neck. The length of rod desired to be inserted into the flask neck was turned down on a
lathe so that it was small enough that there was room for a couple of wraps of Teflon plumbers tap between it and the inside of the flask neck. When
the stopper was cut from the full piece of rod at least a small section of full diameter rod was left attached to keep the stopper from falling into
the flask and to act as a handle. The couple of wraps of soft and elastic Teflon tape used compresses and conforms very well to slight irregularities
in the flask neck and Teflon stopper providing a good seal. Electrical tape was added to prevent the stoppers from shifting or coming out in storage.
Only a very slight smell of iodine is detected around the stoppers.
I could have done a much neater job of making the stoppers (they were made in only a few minutes).
![Iodine Stored In Erlenmeyers With Homemade Teflon Stoppers.jpg - 166kB](https://www.sciencemadness.org/whisper/files.php?pid=373070&aid=35591)
[Edited on 30-11-2014 by Hennig Brand]
"A risk-free world is a very dull world, one from which we are apt to learn little of consequence." -Geerat Vermeij
|
|
quantumcorespacealchemyst
Banned Shitposter
Posts: 213
Registered: 17-10-2014
Member Is Offline
Mood: No Mood
|
|
cool. as far as liners, there is teflon sheet i use on ebay for seals and weigh boats. the only trouble is forming a seal around the bottom of corks
for me, the side walls can wrap. my idea, others probably before, is if one has a screw top glass bottle, that has a flat top bottom, that a small
amount of teflon sheeting, pressed into the cap mostly prior to screwing down helps to seal rather well, say for bromine (eager to do this, and
liberate bromine from salts). one thing to watch for is if the piece of sheeting isn't pre pressed before screwing on, and/or screwing the cap on too
tight as the edges (of the sheet) weaken/compress and depending on how it is treated may tear around the edges. one may see what i mean by tinkering
with it, i believe it works well.
i got the sheeting on ebay for about 6-7USD a sheet (i quoted this incorrectly as a couple bucks a few places previous to this),
|
|
Hennig Brand
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1284
Registered: 7-6-2009
Member Is Offline
Mood: No Mood
|
|
Using a flat Teflon seal in a screw top is a good idea and is how a lot of the commercially made chemical storage bottles are made. I have been
meaning to try it for a while, but never got around to it or never saw the right container maybe. I think there are a lot of containers, such as screw
top or the metal wire/bale bottle clasp type possibly (if made of glass or other suitable material), that could have their rubber or plastic seals
replaced with Teflon and be used to store iodine and many other things as well. Most of the common plastics aren't really suitable for storing iodine
long term from what I understand.
I looked into it a bit and decided it would be very difficult to cover a rubber or cork stopper with Teflon tape, etc, well enough to make a good seal
and prevent chemical vapors from reaching the stopper. I eventually decided solid Teflon bushings were the way to go.
"A risk-free world is a very dull world, one from which we are apt to learn little of consequence." -Geerat Vermeij
|
|
Benignium
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 115
Registered: 12-6-2020
Member Is Offline
Mood: Quasi-catatonic
|
|
Old thread, I know, but it is mentioned on the wiki page so I decided I'd share my bromine container of choice.
![](https://i.imgur.com/vWndCvj.jpg)
I got this from deschem, on Ebay. The size pictured is 55 mL, but it currently holds 203 grams, which is 65 milliliters, of bromine. Some got on the
threads when I last filled it, but nothing gets past the fluoroelastomer o-ring. I've had bromine in it for months now, wet and dry, and it has held
up perfectly.
Link to product page on Ebay
|
|
TriiodideFrog
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 108
Registered: 27-9-2020
Member Is Offline
|
|
Bromine can be kept in ampoules made out of test tubes or droppers. Just put a small amount of bromine( about half the test ampoule ) and heat the
open end until it closes.
|
|
outer_limits
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 139
Registered: 3-3-2020
Member Is Offline
Mood: hybridized
|
|
I keep bromine in 10ml ampoules.
They have obvious pros:
-easy to fill
-easy to seal
-glass is resistant to bromine
And some cons:
-glass can break (ampoules have not very thick walls, although none of mine broke)
- they have to be discarded when a part of substance is taken, new ampoule have to be filled with remaining part (not necessarily when ampoule was
opened gently and can be sealed)
The bottle that Benignium showed seems great. However for the price of one bottle I could get a load of ampoules.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
The high pressure bottles seem to cost only few $ more for 500mL version compared to 50mL. So, it could be wise considering a larger one, if a need
arises.
Test tubes can indeed be very easily be converted into ampoules of any size available. The tubes should first be preformed to have a narrow neck,
which a pipette or a needle fits, so the heat required to seal the ampoule will be minimal. This type can be sealed within seconds with small torch,
so there will be no risk of heating up the contents. There is also a tutorial for vacuum packaging ampoules - inert gas filling would be easier,
though.
If one has any plan of using the reagent, a predetermined amount could be loaded in an ampoule, so a full charge or a multiplier of it is used every
time a seal has to be broken, to remove the need for repackaging, especially for small amounts.
|
|
RustyShackleford
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 198
Registered: 10-12-2020
Location: Northern Europe
Member Is Offline
|
|
Quote: Originally posted by thethule ![](images/xpblue/lastpost.gif) | Hi guys, i have a nice element collection going, but the 100g of Iodine i put in a screw top jam jar last year has pretty much eroded the metal top
and is slowly escaping into the surrounding element "cubicles" (i have removed the others for now). I'm about to buy another 100g (i live in the UK,
perfectly legal) and was wondering if you guys had a link to a glass jar i could buy to safely keep it as contained as I can be. It has to be room
temp ideally as i have em on display.
Maybe a sealed ampoule would be a better idea? I'm toying with buying some long borosilicate tubes and attempting to make my own. Is that a viable
solution? Will the Iodine survive while im heating the top end of the tube to soften and seal it? Is there any chance of the ampoule shattering if the
pressure inside gets too high from sublimated iodine?
I did a search btw, but the links to jars on the article i found in this forum are dead.
Thanks for reading |
Iodine leaks out of pretty much every bottle, you can greatly decrese the leakage by using a PTFE lined bottle (such as red cap GL45) or just having
it entierly closed as with an ampule. Making an ampule isnt hard at all, especially with iodine-.
|
|
Belowzero
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 173
Registered: 6-5-2020
Location: Member Is Offline
Member Is Offline
|
|
My iodine is stored wet in a glass bottle with a glass stopper which is wrapped in regular plastic foil, it has been stable sitting around for years
without any noticeable change.
Boring but effective.
Only downside is that when I need it I have to get it out of solution.
[Edited on 2-2-2021 by Belowzero]
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Iodine stores perfectly in a coke bottle.does not leak at all
Bromine will escape from anything except a sealed glass vial.
The ONLY other option is to keep it frozen in a PFA bottle as uc235 does
in his bromine video
Anything else leads to gradual escape of bromine.
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by Benignium ![](images/xpblue/lastpost.gif) | Old thread, I know, but it is mentioned on the wiki page so I decided I'd share my bromine container of choice.
![](https://i.imgur.com/vWndCvj.jpg)
I got this from deschem, on Ebay. The size pictured is 55 mL, but it currently holds 203 grams, which is 65 milliliters, of bromine. Some got on the
threads when I last filled it, but nothing gets past the fluoroelastomer o-ring. I've had bromine in it for months now, wet and dry, and it has held
up perfectly.
Link to product page on Ebay
|
$40 for the test tube and $1000 for delivery.wtf?
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
$40 for the tube and $5 for delivery.
I think that $40 for a single tube is quite a lot of money. I make ampoules for stuff like Br2.
|
|
mr_bovinejony
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 130
Registered: 20-4-2018
Member Is Offline
Mood: ASS
|
|
Why has no one mentioned storing bromine under a layer of sulfuric acid and in the freezer? If you don't want to melt glass then this seems like the
best way
|
|
clearly_not_atara
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2725
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
For maximum convenience, you can also "store" bromine by making potassium bromate and put it in a $1 jar on the shelf... ok, there's work involved,
but there's also work involved in sealing an ampoule!
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by clearly_not_atara ![](images/xpblue/lastpost.gif) | For maximum convenience, you can also "store" bromine by making potassium bromate and put it in a $1 jar on the shelf... ok, there's work involved,
but there's also work involved in sealing an ampoule! |
Sealing an ampoule is a lot less work than going back to square one and reextracting,
distilling and drying all over again
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by woelen ![](images/xpblue/lastpost.gif) | $40 for the tube and $5 for delivery.
I think that $40 for a single tube is quite a lot of money. I make ampoules for stuff like Br2. |
It said $999 for delivery when I looked at it
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
Quote: Originally posted by mr_bovinejony ![](images/xpblue/lastpost.gif) | Why has no one mentioned storing bromine under a layer of sulfuric acid and in the freezer? If you don't want to melt glass then this seems like the
best way |
Are you Speaking from experience or guessing here?
[Edited on 4-2-2021 by draculic acid69]
|
|
clearly_not_atara
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2725
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Making bromine from (clean) potassium bromate is a lot easier than making it from any OTC precursor. Back to square three, maybe. Just
combine with hydrobromic acid (itself not that hard to store) under cooling.
Plus, you can use bromate directly in many procedures where you might otherwise want to use bromine, including e.g. aromatic bromination.
|
|
FrenchChemist
Harmless
Posts: 43
Registered: 25-1-2021
Member Is Offline
|
|
only screw cap line from PBT with PTFE coated silicone seal
![](https://i.ibb.co/X28BX6T/04081.jpg)
|
|
Tellurium
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 84
Registered: 12-7-2017
Location: Group 16, Chalcogen City
Member Is Offline
Mood: smelly
|
|
I stored my Br2 in glass ampules before, but I think I found a way better solution now. I'm using the "pure premium" caps for the GL45 duran Bottles.
They are made out of TFA with a PTFE liner. I put a quantitiy of Br2 in one bottle and stored it outside for a year, so it even got warm in the
summer. Now after over a year there isn't even the slightest bit that got out, it still weights the same.
But if you don't find them relatively cheap secondhand they are very expensive, but a better solution to ampules, as you can just take the amount out,
that you need.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I have a bottle of iodine that's over 10 years old, opened a couple of times and haven't ever noticed anything noteworthy on it's wellkeeping. I
haven't found iodine to be difficult to store, hence.
|
|
Tellurium
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 84
Registered: 12-7-2017
Location: Group 16, Chalcogen City
Member Is Offline
Mood: smelly
|
|
With Iodine I also don't have any issues at all. Especially since I'm storing it in the freezer.
|
|
Amos
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
An ordinary glass reagent jar from the old days with a plain rubber stopper is basically flawless. I've been using the same iodine for 6 years
without issue.
|
|
Texium
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4547
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
You’re in Australia right? That’s Deschem’s way of
saying that they aren’t allowed to ship to Australia anymore.
Those pressure tubes are nice though. I’ve used them for running high pressure reactions, some of which contained some pretty nasty stuff under
pressure, and they still held up perfectly. The key is that you use a good quality o-ring, like Viton, and replace it if it ever starts getting
crispy. The lids themselves are solid PTFE: not gonna be touched by anything.
Edit: but to be clear, I think they’re overkill for bromine. Bromine is fine in a regular media bottle in the freezer. Keep it frozen when you
aren’t using it and you won’t have problems. I would be more inclined to use a pressure tube to store reagents that are both corrosive and water
sensitive, since storing water sensitive stuff in the freezer can get messy due to condensation.
[Edited on 2-17-2021 by Texium (zts16)]
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
If they just say we no longer ship to Australia it's a lot easier than trying to decode
such a ridiculous delivery price. have any other Australians seen this with deschem? Is it just this product or all glassware? And since when
have they cared whether or not there "allowed"
|
|
Pages:
1
2
3
4 |