sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
Purifying Deuterium Chloride solution
Hi all,
I recently purchased on eBay 50g of 32% deuterated hydrochloric acid in D2O. I was really looking for a sample of D2O but I figured that this was even
better since I could always neutralize it and separate out the D2O if I needed. Unfortunately, when it arrived, I found that the bottle had been
sealed inside a shipping container for many years and had eaten through its own cap during that time, so that the acid is contaminated by dissolved
organics from the plastic. It was still contained within the plastic bag which surrounded the bottle, so that I recovered almost the entire original
volume in a new glass container.
I am looking for suggestions which would allow me to purify this to remove the brown dissolved contaminants. Ideally, I'd like to get something as
close to the original 32% deuterium chloride in D2O as I can. However, I am also open to options which result in fairly pure D2O. I guess my highest
priority is to get as little remaining protium (Hydrogen 1) contamination as possible. I realize that this is challenging because no doubt there is
hydrogen in the contaminants and some of that must have dissociated in the heavy water/acid.
Ideas?
Thanks,
Sean
|
|
Metacelsus
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2537
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
My idea: Get a refund.
Removing protium contamination from heavy water is probably not worth the effort.
[Edited on 3-8-2014 by Cheddite Cheese]
|
|
TheChemiKid
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 493
Registered: 5-8-2013
Location: ̿̿ ̿̿ ̿'̿'̵͇̿̿з=༼ ▀̿̿Ĺ̯̿̿▀̿ ̿ ༽
Member Is Offline
Mood: No Mood
|
|
I second that idea.
When the police come
\( * O * )/ ̿̿ ̿̿ ̿'̿'̵͇̿̿з=༼ ▀̿̿Ĺ̯̿̿▀̿ ̿ ༽
|
|
sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
OK, yes, if I needed this for some special purpose, then yes, I agree. However, I have not seen heavy water available to hobbyists in a long time, and
I don't think this guy has more of this, so if I get a refund and have to send it back, I am in a worse situation than I am now. Even if all of the
hydrogen from the organic material were to be incorporated into the water, it would still be probably >90% heavy water, and that's a whole lot
better than nothing.
|
|
sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
Let me clarify something - I do not expect to separate out any protium which has already been incorporated as H3O+ ions, H2O, or HCL. I just would
prefer to use some kind of reaction to purify it which would not create additional amounts of these species in the process. Right now, it is colored
dark brown and I just want to get most of that junk out of it!
[Edited on 3-8-2014 by sbreheny]
|
|
Zyklon-A
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1547
Registered: 26-11-2013
Member Is Offline
Mood: Fluorine radical
|
|
If you knew what the destroyed cap was made out of that would be a start.
Distillation should give the results you want either way.
|
|
prof_genius
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 147
Registered: 15-5-2013
Member Is Offline
Mood: No Mood
|
|
Try distilling it under a dry inert atmosphere.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Distilling 32 % DCl won't work very well.
The DCl gas would come off until you reached the azeotrope - about 20% (I'm guessing it's about the same as the HCl H2O azeotrope which is 20.2% HCl).
If you trapped that gas somehow and then dissolved it back in the distilled acid you would get back to (nearly) what you started.
|
|
Burner
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 100
Registered: 28-3-2014
Member Is Offline
Mood: No Mood
|
|
How about neutalizing the DCl with sodium carbonate and then distilling the D2O?
“There is a cult of ignorance in the United States, and there has always been. The strain of anti-intellectualism has been a constant thread winding
its way through our political and cultural life, nurtured by the false notion that democracy means that 'my ignorance is just as good as your
knowledge.”
- Isaac Asimov
|
|
chornedsnorkack
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 553
Registered: 16-2-2012
Member Is Offline
Mood: No Mood
|
|
How would freezing work?
HCl*3H2O (about 40 % HCl) freezes at -25 celsius. It should be frozen out of the 32 % DCl till an eutectic with HCl*6H2O is reached at -73 celsius and
about 26...27 % DCl.
|
|
APO
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 627
Registered: 28-12-2012
Location: China Lake
Member Is Offline
Mood: Refluxing
|
|
D2O not available to hobbyists in a long time? Have you looked here?
"Damn it George! I told you not to drop me!"
|
|
IrC
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2710
Registered: 7-3-2005
Location: Eureka
Member Is Offline
Mood: Discovering
|
|
Quote: Originally posted by sbreheny ![](images/xpblue/lastpost.gif) | OK, yes, if I needed this for some special purpose, then yes, I agree. However, I have not seen heavy water available to hobbyists in a long time, and
I don't think this guy has more of this, so if I get a refund and have to send it back, I am in a worse situation than I am now. Even if all of the
hydrogen from the organic material were to be incorporated into the water, it would still be probably >90% heavy water, and that's a whole lot
better than nothing. |
Not true. United Nuclear has sold D2O in small amounts for years. I have 120 gm of it, two 10 gm and a 100 gm bottle. From the very link APO provided.
"Science is the belief in the ignorance of the experts" Richard Feynman
|
|
sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
I actually found that link a few hours after I posted here saying that I had not seen it in a while. I usually look for chemicals on eBay and Amazon
and I've never seen it come up in searches there until I saw the one I bought. I am surprised that I didn't come across the United Nuclear offering
before because I have ordered other things from them. Thanks for the link.
I would still like to try purifying mine and I think I may resort to neutralizing with a non-hydrogen-containing base (like Sodium Carbonate as
someone suggested) and then distilling to get just D2O.
|
|
Dan Vizine
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 628
Registered: 4-4-2014
Location: Tonawanda, New York
Member Is Offline
Mood: High Resistance
|
|
Try activated charcoal (dried).
|
|
AJKOER
Radically Dubious
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Stratetgy: Separate out the H2 and D2 as gases. This should reduce the presence of impurities and a cooling of the gas mixture, given the relative
weights of the gases, could improve the D2 concentration as well.
Try adding Zn, boil and collect the gases. Cool to separate out any hydrocarbons, or captured distilled D2O and H2O, which you can recycle.
From the DCl, you get D2 and ZnCl2.
From the boiled H2O and D2O with Zn, you get Zn(OH)2, Zn(OD)2, H2 and D2.
As Zn(OH)2 (also I would guess the Zn(OD)2 as well) decompose releasing its water at 125 C, apply mild heat to the dry salt, to retrieve any D2O along
with H2O to recycle.
[Edited on 12-8-2014 by AJKOER]
|
|
sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
I finally got a chance to do more work on this and I managed to purify it by distillation. I just distilled it directly without neutralizing the acid,
using a fume hood.
The mass of the starting material was 39.92g. The mass of the product was 31.98g. This seems to be an excellent yield given that there was a visible
amount of contaminant solid remaining in the boiling flask and a large amount of DCl was lost as gas (assuming that the azeotrope is the same mass
percent for DCl in D2O as HCl in H2O, then the product should be about 20% DCl by mass, but the original label stated 35% DCl by mass - although some
was probably lost in reaction with the plastic that it ate).
The starting material was a dark brown opaque liquid with a horrible foul smell (not just the normal fuming HCl smell). The product has almost no
smell (lower DCl concentration so much less DCl outgassing) and is clear. pH test paper shows that its pH is 1 or less (as low as the paper goes).
Density of the product is (very roughly) 1.3g/mL. My back of the envelope calcs suggest that it should be 1.2g/mL. When I measured 1.3, I was only
estimating volume by the graduations on a bottle, I did not yet do a proper volume measurement.
One remaining question is how much D vs H exchange happened due to mixing with water vapor in the air during the distillation. If it absorbed H2O from
the air, that could falsely "improved" my yield.
Thanks for your help,
Sean
|
|
careysub
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
Measuring Iostopic Composition
Probably the easiest method of measuring the actual isotopic composition is with a refractometer.
See Section 1-2.16 in:
http://books.google.com/books?id=HwhTSGufJdYC&pg=PA26&am...
But you need a good refractometer to be very useful.
The refractive index difference is 0.004687, and is linear with D molar concentration, so a cheap refractometer reading to 0.001 will only give you a
rough estimate that can distinguish between 0%, 20%, 40%, etc. but not finer than that. A common type used for sugar content (measuring in Brix from
0-10% Brix) can read to 0.1% Brix, which corresponds to an RI resolution of 0.00014 and an isotope concentration resolution of about 3%.
|
|
sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by careysub ![](images/xpblue/lastpost.gif) | Probably the easiest method of measuring the actual isotopic composition is with a refractometer.
See Section 1-2.16 in:
http://books.google.com/books?id=HwhTSGufJdYC&pg=PA26&am...
But you need a good refractometer to be very useful.
The refractive index difference is 0.004687, and is linear with D molar concentration, so a cheap refractometer reading to 0.001 will only give you a
rough estimate that can distinguish between 0%, 20%, 40%, etc. but not finer than that. A common type used for sugar content (measuring in Brix from
0-10% Brix) can read to 0.1% Brix, which corresponds to an RI resolution of 0.00014 and an isotope concentration resolution of about 3%.
|
Thanks for the suggestion - I don't have a refractometer and I don't think I am going to buy one just for this investigation.
|
|
sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
I obtained a better density measurement using a volumetric flask: 1.184g/mL. Alfa Aesar's online catalog lists the density of 20% w/w DCl in D2O as
1.20g/mL with a boiling point of 108 deg C. I observed 108 deg C during most of the time that the product was coming over during the distillation.
I'm pretty happy with that result.
[Edited on 6-9-2014 by sbreheny]
|
|
sbreheny
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 145
Registered: 30-1-2014
Member Is Offline
Mood: No Mood
|
|
I wanted to share a few photos of my distillation set-up for doing this. One photo shows the "before and after" shot of the contaminated DCl in D2O
and the product. Neither of them is in the original bottle, which leaked, but the original label is on the "before" photo. The other two photos are
the distillation set-up and a wider shot of it in my hood. I am in the process of converting an enclosed porch into a home lab and this is the
centerpiece of it. The boiling flask is in a mineral oil bath and I used an aquarium circulation pump to cycle cool water through the condenser. When
I took the photo, no product had come over yet - when it began to transfer, I added ice to the water container.
![hood.jpg - 362kB](https://www.sciencemadness.org/whisper/files.php?pid=344409&aid=33562)
[Edited on 6-9-2014 by sbreheny]
|
|
careysub
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
Deuterium Element Display
A little off-topic perhaps - but a neat display in an element collection would be two test tubes, one with light water, and one with heavy
side-by-side with something of a density between the two in both - floating in heavy water and sunk in light water.
There aren't two many cases where you can conveniently display two pure samples of different isotopes of an element.
Question: any suggestions for what would make a good float? You could always manufacture a float, but it is not a good demo because they could have
been made differently. The same homogeneous substance in both is more compelling. Obviously insolubility is a requirement. Polystyrene has a density
of 1.05 and would fit the bill.
|
|
Brain&Force
Hazard to Lanthanides
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1302
Registered: 13-11-2013
Location: UW-Madison
Member Is Offline
Mood: Incommensurately modulated
|
|
Or try putting normal water and heavy water in equal volumes on different sides of a balance. More difficult, and I like the polystyrene suggestion
better.
At the end of the day, simulating atoms doesn't beat working with the real things...
|
|