jamit
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 375
Registered: 18-6-2010
Location: Midwest USA
Member Is Offline
Mood: No Mood
|
|
Buchi rotovapor el131
I just received a buchi rotovapor model el131. I think it's an old one. I have never owned one of these unit and so I'm wondering what can I do with
it.
Now I'm missing some parts and will need to buy them but before investing on that I want to know what I can do with it in a home lab setting. Can
some of you who have a rotovapor help fill in my lack of experience.
I' ve read wiki and other articles on the web and YouTube but they don't address its practicality for a home chemist. I know I can separate mixtures
of solvents but what else can you do?
Can I distill nitric acid?
Is a rotovapor better at distilling then a regular RBF distillation set up?
What practical use is there with the rotovap in the home lab. I realize this is a very general question depending onus purpose... But I have it now
and I want to know whether its worth investing in completing the whole rotovapor. Any suggestion or links will be appreciated.
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
A rotavap isn't for separating solvents. Thats what a fractionation setup is for.
Put simply, a rotavap is for the quick removal of solvents under reduced pressure, in order to isolate the dissolved substances, whether solids or
oils. Clearly, if your gear is sufficiently volatile, you should excise caution that you don't have substantial losses due to vaporisation (use low
boiling solvents that are easy to remove such as ether or pentanes or DCM) - the same applies if your gear is thermally unstable.
A rotavap is really for organic synthesis. After working up your reaction 90% of the time your desired product is in an organic solvent of some
description (which has been washed with appropriate solutions, usually acid/base, water, then brine, and finally dried over a dessicant like Na2SO4 or
MgSO4). Stripping the solvent off under reduced pressure then gives you the crude product, which can then be further purified by fractional
distillation, sublimation or chromatography. If you go the route of chromatography, then you'll end up with your product dissolved in several
fractions, which will be combined and the solvent again removed using the rotavap to isolate your purified material.
I used to have a Buchi Model M which is fucking ancient and microscale... Its currently being lent to a friend, but the point is this model had
several auxillary pieces of glass available for it (see attachment). One of which was a Soxhlet extractor body, but there was also a fractionation
set. I don't know if these were/are made commercially for the larger models, but I'm sure if you're friendly with a glassblower and have the cash, you
could get one made.
I would not advise using this for distilling nitric acid, though there shouldn't be any reason it can't be. I suspect you'll cause the vacuum seal to
perish at a faster-than-usual rate. I've heard they're not particularly fond of acetic acid either.
[Edited on 4-10-2013 by DJF90]
Attachment: Rotavapor_M.PDF (757kB) This file has been downloaded 383 times
|
|
S.C. Wack
bibliomaster
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
http://www.mybuchi.com/Training-Papers.16023.0.html
also on the page: "Purchase a Rotavapor R-3 for $1,995"
or a demo for $1,732.71
not that they'd ship one to me here
|
|
MrHomeScientist
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
I just recently got to set up and use an IKA RV-10 rotovap at work, and never having used one before I was amazed at how awesome it is. The advantages
I've seen are 1) very efficient condensing of solvent, 2) gentle and even evaporation for fragile compounds, 3) pulling vacuum allows for lower
temperature distillation (saving energy and time). I only tested it with water so far, but was amazed at how fast it works. I would love one at home
for any procedure involving distillation. Should work fine for nitric distillation, as it's all ground glass. I'd be nervous about leaking fumes out
onto my expensive rotovap though! You'd need to take extra care to not allow fumes to make it to your vacuum pump as well.
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by MrHomeScientist ![](images/xpblue/lastpost.gif) | I just recently got to set up and use an IKA RV-10 rotovap at work...
...Should work fine for nitric distillation, as it's all ground glass. |
Did you not see the polymer seal? A cursorary search reveals IKA sell replacements for £61.50...
I'll re-cap. Yes, you probably can use it to distil nitric acid. BUT, your seals probably won't last as long as they should. What's wrong with using
proper glass to distil nitric acid? (or anything else for that matter).
[Edited on 6-10-2013 by DJF90]
|
|
MrHomeScientist
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
Of course you're right. For some reason I was under the impression the condenser connected directly to the vapor tube, but that's obviously not right.
My seal is teflon, though, so I would think it would stand up pretty well.
I agree, though: just use a regular distillation setup for acid distillation and leave the rotovap for what it was intended, i.e. removing solvents.
|
|
jamit
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 375
Registered: 18-6-2010
Location: Midwest USA
Member Is Offline
Mood: No Mood
|
|
The impression I get from DJF90, MrHomeScientist and S.C. Wack is that Rotovapor is for the most part, not a practical lab equipment for the home lab.
I mean, how many of us are there that needs to remove solvents on a monthly or bimonthly basis? And even if you're really into organic chemistry is
there a regular use for a rotovap?
Can someone direct me to some experiments or lab exercise I can do to learn more about the functionality and uses for the rotovap? Sorry if this is a
newbie type of question, but I have a rotovap and if its not very useful, I'll sell it - it takes up a lot of space and there's no use in keeping it
if I'm not going to use it very much.
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
I use a rotavap on a daily basis at work, and the one at home is used almost as often as I do any chemistry. My rotavap broke a couple times and I
felt lost without it. It just shaves so much time off when doing org chem its a worthy investment if thats your field of interest.
|
|
jamit
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 375
Registered: 18-6-2010
Location: Midwest USA
Member Is Offline
Mood: No Mood
|
|
I'm sorry if I'm sounding like a newbie... because I am, so far as using a rotovap is concerned. What kind of organic experiment can you do at home
that would require a rotovap on a regular basis and therefore "worth the investment"? I really want to keep my rotovap el131 but in order to justify
it I want to know what I can do with it... and what kinds of experiments are possible... please be as specific as possible or direct me to a link or
articles, etc. thank you in advance!
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
As I said, 90%+ of organic experiments will require you to strip off solvent at some stage. You can of course get texts that discuss experiments where
a rotavap is avoided (e.g. vogel). In these cases product is usually isolated by crystallisation from the reaction mixture or by distillation of a
crude oil after aqueous workup)
|
|
Lambda-Eyde
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 859
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
Quote: Originally posted by jamit ![](images/xpblue/lastpost.gif) | I'm sorry if I'm sounding like a newbie... because I am, so far as using a rotovap is concerned. What kind of organic experiment can you do at home
that would require a rotovap on a regular basis and therefore "worth the investment"? I really want to keep my rotovap el131 but in order to justify
it I want to know what I can do with it... and what kinds of experiments are possible... please be as specific as possible or direct me to a link or
articles, etc. thank you in advance!
|
No organic experiments you can do at home require a rotavap, it is simply a (very) convenient apparatus for the quick, gentle and easy
removal of solvents from a solution. Of course this can also be done with a conventional distillation apparatus but the rotavap simplifies and
improves the process immensely. You don't have to assemble the apparatus (setting up stands, lubing joints, using keck clips, aligning the whole setup
correctly and so on) as the rotavap is always assembled and just waiting for a flask to be connected, you don't clean it after each use, condensation
is often much more efficient, you don't have to watch it all the time plus it's a lot faster due to the vacuum and rotation. You're essentially
reducing the task of removing solvents from reaction mixtures from a separate distillation process that takes two hours to just putting a
flask on the rotavap and forgetting about it for 20 minutes.
If you're not doing much synthetic organic chemistry (and don't plan to), I think you're better off selling your rotavap.
This just in: 95,5 % of the world population lives outside the USA
You should really listen to ABBAPlease drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
jamit
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 375
Registered: 18-6-2010
Location: Midwest USA
Member Is Offline
Mood: No Mood
|
|
Thank you all for your input. One thing more... Can you direct me to some experiments I can do to learn about rotovap. Thanks.
|
|