| Pages:
1
2
3 |
DubaiAmateurRocketry
National Hazard
Posts: 841
Registered: 10-5-2013
Location: LA, CA, USA
Member Is Offline
Mood: In research
|
|
Concentrating Nitric acid
Hi,
Because i need a high nitric acid concentration, preferbly over 95%, for something, I want to know how to concentrate the acid in easiest way.
First, I made my nitric acid by blowing NO2 gas bubbles into cold water. For around half an hour until the color becomes yellow, so i guess it has at
least around 10% ?
Just trying to figure out how to concentrate it to >95% ?
Can i use salt that absorb water to become hydrated in order to suck the water out ? such as Lithium perchlorate ? or Copper sulfate ?
I would want to use Lithium Perchlorate because it has a low solubility in water when it is hydrated so yeah. And i have a lot of it any ways, and i
can reuse it simply by dehydrating it on an oven so i think it might be convienient ?
Will that work ?
and how do i know how much of it shall i add when i am not sure of the concentrating of my nitric acid ?
How do i know if my filter paper will react with high % HNO3 ?
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
First, titrate it to determine the concentration. Assuming it is low, I would convert it to a nitrate salt with a stoichiometric amount of alkali,
evaporate the water, and then mix the salt with sulfuric acid and distill off concentrated nitric acid, preferably under vacuum. This distillation
process has been heavily covered under other threads.
Adding a salt such as lithium perchlorate will just dissolve the salt in the nitric acid.
|
|
|
AndersHoveland
Hazard to Other Members, due to repeated speculation and posting of untested highly dangerous procedures!
Posts: 1986
Registered: 2-3-2011
Member Is Offline
Mood: No Mood
|
|
If one has 90% conc. nitric acid, and wants to concentrate it further, it can first be saturated with nitrogen dioxide and then a dry stream of ozone
passed through. This can bring the concentration up to anhydrous, or even further. This route is most practical for already high concentrations, where
one only needs to raise the concentration by a little more.
|
|
|
Variscite
Hazard to Self
Posts: 69
Registered: 21-5-2013
Member Is Offline
Mood: diffusing
|
|
Do you have a reference for that, Anders? Ive honestly never heard of that.
|
|
|
Pulverulescent
National Hazard
Posts: 793
Registered: 31-1-2008
Member Is Offline
Mood: Torn between two monikers ─ "hissingnoise" and the present incarnation!
|
|
Anders is correct, but the method is obviously barely practical!
Distill 90% HNO3 from an equal volume of conc. H2SO4 to bring it to >95% . . .
"I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones"
A Einstein
|
|
|
bfesser
|
Thread Moved
11-9-2013 at 05:18 |
Ascaridole
Hazard to Self
Posts: 67
Registered: 11-9-2013
Location: Hawaii, USA
Member Is Offline
Mood: Searching for glass....
|
|
You may want to bubble your NO2 into hydrogen peroxide, will help your yield.
As for concentrating the acid I'm assuming you probably don't have access to concentrated Sulfuric acid?
If you do just carefully add the acid to the nitrate salt and distill off nearly anhydrous or possibly better nitric acid. Just be careful, your
working with two very strong acids that can kill you.
If you don't have access to the concentrated sulfuric acid your best bet is to use distillation to get your 10% up to about 70% after that the
azeotrope won't break easily without a strong dehydrating agent like sulfuric acid. You could try a modified method of Anders method by bubbling more
NO2 into the 70% acid and blowing ozone through it. It will be a slow and expensive process but possibly doable.
Last but not least if you can find sodium bisulfate NaHSO you can mix it in a 1:1 molar ration with your nitrate salt and distill it to get nearly
anhydrous nitric acid. It will be heavily contaminated with NO2 as the high heat needed will decompose a fair amount of your nitrate. An alternative
is to use an aqueous mixture of the salts and distill off the 70% nitric acid azeotrope.
Either way making nitric acid and getting it to >95% is not a cheap or easy task. Even the stuff I use in the lab is around 70% (15M).
|
|
|
malford
Hazard to Others
Posts: 116
Registered: 17-6-2013
Member Is Offline
Mood: No Mood
|
|
Could someone elaborate on this?
I am wondering, specifically, what is mean by saturating it with nitrogen dioxide.
Passing a dry stream of ozone through it could be accomplished with a setup such as this one.
|
|
|
Ascaridole
Hazard to Self
Posts: 67
Registered: 11-9-2013
Location: Hawaii, USA
Member Is Offline
Mood: Searching for glass....
|
|
Essentially NO2 is dissolved in the solution by bubbling and ozone will react with it to form NO3. NO3 reacts with more NO2 to form N2O5 that gets
hydrolized to HNO3. At least that's what I can remember.
|
|
|
malford
Hazard to Others
Posts: 116
Registered: 17-6-2013
Member Is Offline
Mood: No Mood
|
|
Pulvurulescent said that would be barely practical. Why?
What increases the solvation of nitrogen dioxide in the nitric acid? How about warming the nitric acid, small bubbles for high surface area, long
travel distance for increased exposure?
|
|
|
Ascaridole
Hazard to Self
Posts: 67
Registered: 11-9-2013
Location: Hawaii, USA
Member Is Offline
Mood: Searching for glass....
|
|
"Barely Practical" as in on an industrial scale it would be worth all the effort to setup the all the gas generators and stuff. As you said yourself
to increase efficiency a fritted gas dispersion tube and a long travel distance are needed for the process to be practical. On a small scale such a
setup would probably cost more than going out and paying for concentrated nitric acid. As for heating that would do more harm than good as nitric acid
undergoes thermal decomposition.
I believe NO2 is more soluble in nitric acid than in water because NO2 gets hydrolized in water to nitric acid and NO (if bubbled in H2O2 no NO is
produced increasing efficiency). As more and more HNO3 is made NO2 begins to exist in equilibrium with the acid. At least thats what I can figure out.
|
|
|
Fantasma4500
International Hazard
Posts: 1681
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
i might be mistaken... but LiClO4 + HNO3 > HClO4 + LiNO3
HClO4 = you dont want that (:
whats the purpose of the high conc. HNO3 anyways? many nitrations are very possible with HNO3 below the azeotrope, otherwise just get some nitrate
salt, that will give you anhydrous HNO3, but this isnt always preferred for nitrations as it tends to get hard to stir, especially if the ppt. is
solid aswell
|
|
|
softbeard
Hazard to Self
Posts: 69
Registered: 23-7-2013
Member Is Offline
Mood: moody
|
|
It is also possible to use magnesium nitrate to concentrate nitric acid. I am fuzzy on the details because this is coming from memory of a book on the
manufacture of nitric acid I read a long time ago, but I believe magnesium nitrate was used commercially to break the nitric acid/water azeotrope.
Sorry I don\t have refs. and partial pressure tables.
|
|
|
ElectroWin
Hazard to Others
Posts: 224
Registered: 5-3-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by softbeard  | | It is also possible to use magnesium nitrate to concentrate nitric acid. I am fuzzy on the details because this is coming from memory of a book on the
manufacture of nitric acid I read a long time ago, but I believe magnesium nitrate was used commercially to break the nitric acid/water azeotrope.
Sorry I don't have refs. and partial pressure tables. |
i assume this works similarly to the way you can concentrate acetic acid by adding anhydrous CaCl2 and then distill?
i expect magnesium nitrate has a great affinity for water, therefore during distillation lets the HNO3 boil off first. So use anhydrous Mg(NO3)2.
|
|
|
Ascaridole
Hazard to Self
Posts: 67
Registered: 11-9-2013
Location: Hawaii, USA
Member Is Offline
Mood: Searching for glass....
|
|
The magnesium nitrate method might work industrially but on a small scale I have a feeling it's another barely practical approach. Just as trying to
dehydrate magnesium chloride results in formation of the oxide and HCl without careful controll of temperature the same is true for the nitrate. The
only serious way an anhydrous or close to anhydrous magnesium nitrate could possibly be obtained would be through azeotropic drying via
crystallization from an anhydrous ethanol solution or possibly drying at low pressure.
The truth be told nitric acid above the 68%-70% mark is hard even for professional chemists to obtain. Perhaps this is one synthesis we should accept
as being difficult and dangerous without a professional setup and the proper reagents.
|
|
|
softbeard
Hazard to Self
Posts: 69
Registered: 23-7-2013
Member Is Offline
Mood: moody
|
|
From what I recall, the magnesium nitrate was made in-situ by adding magnesium oxide to the weak nitric acid. It would break the nitric acid/water
azeotrope and hold on to some of the water while concentrated nitric distilled off. The leftover magnesium nitrate solution was then concentrated by
boiling off some of the water and re-used. I agree, the method is probably trickier than it sounds since the hydrate
,Mg(NO3)2.6H2O ,does indeed decompose before it fully dehydrates by heat. I think the dehydration of the magnesium nitratewas
performed under reduced pressure
Probably best to stick with sulfuric acid for the azeotrope-breaking.
[Edited on 13-9-2013 by softbeard]
|
|
|
DubaiAmateurRocketry
National Hazard
Posts: 841
Registered: 10-5-2013
Location: LA, CA, USA
Member Is Offline
Mood: In research
|
|
| Quote: Originally posted by Antiswat | i might be mistaken... but LiClO4 + HNO3 > HClO4 + LiNO3
HClO4 = you dont want that (:
whats the purpose of the high conc. HNO3 anyways? many nitrations are very possible with HNO3 below the azeotrope, otherwise just get some nitrate
salt, that will give you anhydrous HNO3, but this isnt always preferred for nitrations as it tends to get hard to stir, especially if the ppt. is
solid aswell |
Umm, what about anhydrous Copper Sulfate ?
and are u sure nitric acid can do that ?!
[Edited on 13-9-2013 by DubaiAmateurRocketry]
|
|
|
Fantasma4500
International Hazard
Posts: 1681
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
anhydrous CuSO4 as in for removing water from low concentration HNO3, right?
that should work, but gypsum should work aswell..
CuSO4 anh. can take per mole, up to 5 moles of water (5 x 16 mL / g H2O) thats 80 mL
but you need to keep in mind that you might need to squeeze the now wet CuSO4 to get more HNO3 out of it..
but however man... theres another approach..
get H2SO4, then boil it until it starts to fume, this should potentially work even at 70% to drag a larger amount of water onto the H2SO4, again this
isnt something im fully sure about, you can keep on boiling it to 300*C, when its at 300*C and doesnt boil anymore you have around 98% H2SO4, which
will surely work to remove the water
it can thereafter be added to boil off water and procedure can be repeated over and over with small H2SO4 loss during the concentrating from 70% to
98%
keep in mind SO3 is extremely nasty stuff if you decide to do this
otherwise theres yet against another possibility.. to get from 1 to 70% you could potentially use CaCl2 as dessicant, or silica gel, this would drag
the water out of the HNO3, and you can remove dessicant, boil water off it so its dry and add to dessicant bag and repeat, and then use H2SO4 to get
it to 99%
|
|
|
softbeard
Hazard to Self
Posts: 69
Registered: 23-7-2013
Member Is Offline
Mood: moody
|
|
Instead of copper sulfate, you might as well try anhydrous magnesium sulfate as your dessicant for the nitric acid. Probably it'll act more or less
like magnesium nitrate (which it will partially form anyways when you add it to nitric acid).
Real cheap too.
Of course you have to distill off the nitric acid from a mix like this.
[Edited on 13-9-2013 by softbeard]
|
|
|
Ascaridole
Hazard to Self
Posts: 67
Registered: 11-9-2013
Location: Hawaii, USA
Member Is Offline
Mood: Searching for glass....
|
|
Well if you have a ton of magnesium just reflux your 70% with magnesium shavings. You will loose some of your acid but it will generate your magnesium
nitrate anhydrously and not produce a water in the process. You may not need to reflux it as the magnesium is pretty reactive but who knows, might
passivate in the strong acid as more water is removed.
|
|
|
AndersHoveland
Hazard to Other Members, due to repeated speculation and posting of untested highly dangerous procedures!
Posts: 1986
Registered: 2-3-2011
Member Is Offline
Mood: No Mood
|
|
Nitric acid is also soluble in methylene chloride, so if you have a mixture of sodium nitrate and concentrated sulfuric acid, the nitric acid will be
drawn into the methylene chloride layer.
|
|
|
Pulverulescent
National Hazard
Posts: 793
Registered: 31-1-2008
Member Is Offline
Mood: Torn between two monikers ─ "hissingnoise" and the present incarnation!
|
|
The method has been used to produce anhydrous acid from 68%HNO3!
I've not seen mention of nitrate salts in connection with this extraction . . .
"I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones"
A Einstein
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by malford | | What increases the solvation of nitrogen dioxide in the nitric acid? How about warming the nitric acid, small bubbles for high surface area, long
travel distance for increased exposure? |
Yes for the latter two, no for the first. Remember that gases dissolve better in cold solution, so warming would be counterproductive.
Also, it seems that a lot of people are recommending dessicants to concentrate your weak acid into stronger acid. This won't work. Dessicants are used
to remove the last traces of water from an already nearly dry product - they can't pull out a gallon of water from 10% acid solution. (Unless you
wanted to use 100 pounds of dessicant over a few months of drying time, I suppose)
If your acid is close to maximum concentration, then an appropriate dessicant (read: non-reactive with or soluble in your substance) can be used to
bump it up a bit more.
|
|
|
Pulverulescent
National Hazard
Posts: 793
Registered: 31-1-2008
Member Is Offline
Mood: Torn between two monikers ─ "hissingnoise" and the present incarnation!
|
|
| Quote: | | Remember that gases dissolve better in cold solution, so warming would be counterproductive. |
Remember too ─ oxidation rate in soln. is temp. dependant.
"I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones"
A Einstein
|
|
|
Sunil Sharma
Harmless
Posts: 13
Registered: 20-1-2013
Member Is Offline
Mood: No Mood
|
|
Since nitric acid makes azeotrope with water having boiling point 120 deg C and composition 68% nitric acid and 32% water... in this case when you
distill 10% nitric acid solution you will first get the fraction of water and distillation residue will be be around 50/50 mixture of water and nitric
acid... add 98% sulphuric acid to residue in equal quantity and again distill you will get aroud 95% nitric acid as distillate.....
|
|
|
AndersHoveland
Hazard to Other Members, due to repeated speculation and posting of untested highly dangerous procedures!
Posts: 1986
Registered: 2-3-2011
Member Is Offline
Mood: No Mood
|
|
It is barely practical because it takes a large volume of ozone gas to make a very tiny volume of nitric acid. A typical ozone generator, whether
produced by chemical means or electric discharge, is not very efficient, and typically the stream of oxygen coming out only contains 2-4% ozone. Add
to this the fact that this gas stream has to be completely free from moisture, because chances are it contains a significant portion of water vapor
relative to the small concentration of ozone present, and the gas will have to flow through the nitric acid for a long time. This route is not
practical for making any more than very small amounts of nitric acid. The only advantage is that it is not constrained by a maximum concentration.
Hydrogen peroxide can also oxidize NO2 to nitric acid, but the hydrogen peroxide typically contains water. It also leaves behind water after it
oxidizes the NO2. Even assuming you had pure H2O2, the maximum concentration of HNO3 theoretically obtainable would be only 77.7%.
In contrast, ozone only leaves behind O2 after it oxidizes the NO2. You do not need ozone to oxidize aqueous solutions of NO2, it can be oxidized to
nitric acid by regular air, but the maximum possible concentration achievable by oxidation with air is only around 70-77%. That is because O2 can not
actually directly oxidize NO2, but rather relies on an equilibrium that exists in aqueous solutions of NO2, an equilibrium that becomes less
favorable as the concentration increases.
If you are trying to obtain nitric acid through distillation much past the azeotropic concentration, reduced pressure needs to be used, otherwise the
heat will irreversibly decompose a portion of the nitric acid vapor.
[Edited on 17-9-2013 by AndersHoveland]
|
|
|
| Pages:
1
2
3 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
