Thanatops1s
Hazard to Self
Posts: 54
Registered: 24-6-2013
Member Is Offline
Mood: No Mood
|
|
Mantle or hotplace & stirrer for first heating device?
I'm in the process of building up a lab and was wondering what people think would be better for a first purchase? I was originally going to get a
mantle for distillation but then thought that a hot plate would be a better option since I could use a water/oil/sand bath for round bottom flasks,
plus I have the flat surface. I figure for first equipment, versatility is more important, especially when on a limited budget. There was a Thermolyne
Cimarec 2 I was thinking of picking up. Any opinions on that model?
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
A hotplate with a built-in magnetic stirrer is pricey, but nice to have. I recently got one after the insulation on my cheap, crappy "electric stove"
type hotplate cracked and it started electrocuting me. However, if you're on a budget, I would recommend a cheap one, like what I used to have, from
Target or whatever store sells them. They go as low as $12.99:
http://www.target.com/p/kitchen-selectives-single-burner-sb1...
I would definitely recommend a hotplate over a mantle; as you said, you can always use a bath.
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
Definitely go for a hotplate stirrer; they can be used with beakers, erlenmeyers as well as various heating baths for accomodating RBFs and
oddly-shaped containers. Heating mantles are a luxury and something you should only consider when you have a better equipped lab and feel that you use
RBFs often enough to justify it. The stirring feature is also something that will make your life much more pleasant. (I find it kind of ironic that I
own 6 heating mantles and a magnetic stirrer without heating - haven't found the money to buy a hotplate stirrer yet)
I can't vouch for that particular make or model, but Corning and IKA make great stirrer hot plates. To afford them on a mortal's budget you'll have to
buy on the used market. Steer away from the Chinese stuff on eBay.
This just in: 95,5 % of the world population lives outside the USA
Please drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
Thanatops1s
Hazard to Self
Posts: 54
Registered: 24-6-2013
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Cheddite Cheese  | A hotplate with a built-in magnetic stirrer is pricey, but nice to have. I recently got one after the insulation on my cheap, crappy "electric stove"
type hotplate cracked and it started electrocuting me. However, if you're on a budget, I would recommend a cheap one, like what I used to have, from
Target or whatever store sells them. They go as low as $12.99:
http://www.target.com/p/kitchen-selectives-single-burner-sb1...
I would definitely recommend a hotplate over a mantle; as you said, you can always use a bath. |
I'm not sure what you mean by pricy, but my budget is $100 or so. If you mean some of the high end ones brand new, yeah I can't believe how much some
are. But there's two in particular of the same model on ebay now that end tomorrow and the current high bid is $100 so I think I'm leaning towards one
of those.
I've seen some videos on Youtube of people using a round bottom flask directly on a hot plate, is it just me or is that just asking to create a
serious hot spot and break your flask?
[Edited on 10-8-2013 by Thanatops1s]
|
|
|
ElectroWin
Hazard to Others
Posts: 224
Registered: 5-3-2011
Member Is Offline
Mood: No Mood
|
|
when heating stuff for chemistry it is really desirable to be able to regulate temperature to within narrow ranges; so hot-plate with sensor and
closed-loop control goes a long way.
i am lusting for an annealing oven, for doing ceramics work, that lets me program in a sequence of target temperatures and soak-times
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
| Quote: Originally posted by Thanatops1s |
I've seen some videos on Youtube of people using a round bottom flask directly on a hot plate, is it just me or is that just asking to create a
serious hot spot and break your flask? |
Unless we're talking very high temperatures I think that's highly unlikely. I've done it myself for my larger flasks for which I've not had a suitable
mantle, together with a "skirt" of aluminium foil to reduce convection.
The only problem with that technique I'd say is that you're not heating the contents uniformly and that it wastes time and electricity, which can be
alleviated to an extent with the foil skirt.
Edit: also, it is harder to maintain accurate and stable temperatures without a bath.
[Edited on 10-8-2013 by Lambda-Eyde]
This just in: 95,5 % of the world population lives outside the USA
Please drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
smaerd
International Hazard
Posts: 1262
Registered: 23-1-2010
Member Is Offline
Mood: hmm...
|
|
I chose a heating mantel and a stir plate. I never regretted it. I mostly have an interest in organic chemistry though so for the year or so I went
without a hot-plate I had plenty of fun with round bottoms and room temperature/ice-bathed erlenmeyers.
Depends on what you're interested in I guess.
|
|
|
Thanatops1s
Hazard to Self
Posts: 54
Registered: 24-6-2013
Member Is Offline
Mood: No Mood
|
|
Well I'm pretty much a beginner. I've been reading about chemistry for years and am just recently getting into actually doing things instead of just
reading about them. So I guess right at this moment versatility is my main goal. Looks like the hot plate/stirrer is the way to go.
|
|
|
Acidum
Harmless
Posts: 39
Registered: 2-5-2013
Location: Serbia
Member Is Offline
Mood: Sublimed
|
|
Mostly we used heating mantle for distillations of greater amounts of organic solvents (1-5 l), and hotplate magnetic stirrer for everything else,
from reactions to distillations of lesser amounts of chemicals. Versatility of hotplate magnetic stirrer is just unsurpassed... We mostly used IKA,
excellent quality indeed.
That is on faculty, at home I can only dream about those... But if I had a choice, first hotplate stirrer, then mantle for larger batch productions...
...and then I disappeared in the mist...
|
|
|
Thanatops1s
Hazard to Self
Posts: 54
Registered: 24-6-2013
Member Is Offline
Mood: No Mood
|
|
http://www.ebay.com/itm/Thermolyne-Ceramic-2-Hotplate-Stirre...
So I decided on the hot place/stirrer, just won that. A Thermolyne Cimarec 2 for $102.50. There were a lot of pretty beat up ones on there around the
same price, this one looks to be in pretty good condition. It was either not used a ton, or taken good care of.
|
|
|
Thanatops1s
Hazard to Self
Posts: 54
Registered: 24-6-2013
Member Is Offline
Mood: No Mood
|
|
Just got it from Fedex this morning. This thing really is in excellent condition and seems very well made. I think I made the right purchase.
[Edited on 13-8-2013 by Thanatops1s]
|
|
|
Blue Matter
Hazard to Others
Posts: 107
Registered: 20-6-2013
Location: US
Member Is Offline
Mood: Optimus
|
|
I have a hotplate stirrer, a normal hot plate, and a mantle I use my normal hotplate for messy reactions that might spill the hotplate stirrer I only
use on certain occasions when things need stirring and heating, but by far my favorite one is my electrothermal electromantle I got off eBay it heats
up very fast and precisely imho I think hot plate is best for a while but eventually you should get a heating mantle
|
|
|
MichiganMadScientist
Hazard to Self
Posts: 55
Registered: 22-7-2013
Member Is Offline
Mood: No Mood
|
|
I see that you have already made your purchase, and I too, have a high opinion of Thermolyne stirrer/hotplates. Most of mine are made by Corning or
those (Talboys), but I'm conviced that Corning is putting a rather weak magnet on its stirrers these days.
|
|
|
Thanatops1s
Hazard to Self
Posts: 54
Registered: 24-6-2013
Member Is Offline
Mood: No Mood
|
|
I definitely plan to in the future. However seeing as I'm just starting to build up my lab and am on a limited budget, versatility was my main goal
here. Now once my ring stands and clamps come in, I can do my first distillation. For the first one, I'm just doing to use salt water(figure I might
as well do something nice and safe first) but then it's going to be some nitric acid.
|
|
|
Blue Matter
Hazard to Others
Posts: 107
Registered: 20-6-2013
Location: US
Member Is Offline
Mood: Optimus
|
|
Its fun distilling alcohols and seeing how close to pure you can get them by calculating density and then comparing to concentration charts that's
what I did when I got my setup.
|
|
|
jamit
Hazard to Others
Posts: 375
Registered: 18-6-2010
Location: Midwest USA
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Thanatops1s | Just got it from Fedex this morning. This thing really is in excellent condition and seems very well made. I think I made the right purchase.
[Edited on 13-8-2013 by Thanatops1s] |
Thermolyne is a good choice for hotplate stirrer. I have at one time or another owned all the brand names of hotplate/stirrer and the one that is
the best is Corning... any of the PC-351, 320, 420 and 420D and even 620/D are all excellent choice. I also have VWR and Thermolyne and the newer
models are good but the older model is just "so-so".
As for heating mantles... I also own like 5 different sizes and types from Glas-col and Electromantle. But unless you are into organic chemistry...
heating mantles are not as important as a good and reliable hotplate stirrer. Ebay is the best place to get these items.
[Edited on 15-8-2013 by jamit]
|
|
|
ChemSwede
Harmless
Posts: 26
Registered: 20-8-2013
Location: Sweden
Member Is Offline
Mood: No Mood
|
|
Hello.
I'm currently looking for a magnetic stirrer. My budget is set to around 200 EUR.
The cheapest ones are the chinese stirrers on Ebay, but I've heard that they can malfunction quite often.
I would prefer one from Europe.
I've found this seller on Ebay, from the UK:
http://viewitem.eim.ebay.se/-NEW-MAGNETIC-HOTPLATE-STIRRER--...
It's from Maple Scientific. Seems good, but has anyone hade any experience with them?
They also have a homepage: http://www.maplescientific.co.uk/
Any other advice about where to get a good and not too pricey stirrer w hotplate would be appreciated.
[Edited on 24-9-2013 by ChemSwede]
|
|
|
Variscite
Hazard to Self
Posts: 69
Registered: 21-5-2013
Member Is Offline
Mood: diffusing
|
|
Ive had my eye on the pc-351 for a little while and I wish to get it, the only problem ive heard is that it simply doesnt put out enough wattage to
heat larger volumes of liquids efficiently(500 mL+). Does anyone have any input on this?
|
|
|
MichiganMadScientist
Hazard to Self
Posts: 55
Registered: 22-7-2013
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Variscite | | Ive had my eye on the pc-351 for a little while and I wish to get it, the only problem ive heard is that it simply doesnt put out enough wattage to
heat larger volumes of liquids efficiently(500 mL+). Does anyone have any input on this? |
Kind of an old thread, but I'll stick my two cents in....
Any of the Corning brand PC-series hotplate stirrers should be more than sufficient in terms of hearing. I've never had any problems with any of mine.
If anything, my complaint is with the magnetic stirrer. For some reason the magnet on some of Corning's models are weak and fail to hold on to a Stir
bar at high rpms. But again this is just my personal experience. Corning still makes a top notch product...
You can always try wrapping the the hotplate and beaker with aluminum foil to trap heat around the beaker. But again, I personally doubt that you'll
even need to resort to this...
|
|
|
ChemSwede
Harmless
Posts: 26
Registered: 20-8-2013
Location: Sweden
Member Is Offline
Mood: No Mood
|
|
I decided to buy the stirrer/hotplate from Maplescientific. I got it a bit cheaper after mailing with the seller, and it's in the EU, so no customs
fee.
It's chinese made, but so far no problems. Heating and stirring works fine.
|
|
|
Dr.Bob
International Hazard
Posts: 2748
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Thanatops1s |
I've seen some videos on Youtube of people using a round bottom flask directly on a hot plate, is it just me or is that just asking to create a
serious hot spot and break your flask? |
I will add my $0.02 here. I would never use a hotplate to directly heat a rbf. Depending on the brand, size and type of flask, there is a good
chance of breaking the flask, bumping of the solvent, or other issues. There cannot be good thermal transfer with only one point of contact.
I will use them for heating water in a beaker or erlenmeyer flask, but only slowly and gently. And any highly flammable solvent is best heated by
water or oil bath (heating a pan of water/oil and then using that to heat the flask). That works fine for smaller rbfs. For larger ones (~1L and
above), that can be harder, that is where a heating mantle starts to make sense.
|
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
Personally, I prefer a sand bath - it's easy to set up, non-flammable, and heats flasks very evenly.
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
|
Mailinmypocket
International Hazard
Posts: 1351
Registered: 12-5-2011
Member Is Offline
Mood: No Mood
|
|
If you use a coiled element hotplate sandbaths are great. Maybe it's my usual bad luck, but once I was heating a sand bath on a ceramic top hotplate
and it burnt out. I'm not sure if sand baths retain too much heat and screw up the thermostats or something, or it might be bad luck. I wouldn't do
that again though, personally. What a piss of that was!
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
| Quote: Originally posted by Mailinmypocket | | If you use a coiled element hotplate sandbaths are great. Maybe it's my usual bad luck, but once I was heating a sand bath on a ceramic top hotplate
and it burnt out. I'm not sure if sand baths retain too much heat and screw up the thermostats or something, or it might be bad luck. I wouldn't do
that again though, personally. What a piss of that was! |
Sand is an excellent insulator, that's why. I only use sand for very high temperatures (>200 degrees). Below that I go for a heating bath or a
mantle.
Silicone oil is the ideal choice for a heating bath where water can't be used. Inert, non-flammable and very heat stable. You can get it for around
20$ a liter on eBay. Expensive, but well worth the investment considering two liters should last indefinitely.
This just in: 95,5 % of the world population lives outside the USA
Please drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
