elementcollector1
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
Fix a Condenser?
I had a long, borosilicate Liebig condenser, and while I was messing with it, a part of the top connector broke off. It's not ground glass, and I have
2 of the three pieces that broke off. How do I fix this? I would just throw it away, but that seems kind of a waste for something that only had part
of the top broken off. I can repair the first two parts back on with the good ol' blowtorch, but what to do about the missing third part?
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
Nitrator
Harmless
Posts: 27
Registered: 29-9-2012
Member Is Offline
Mood: No Mood
|
|
If you have some broken borosilicate glass handy, than you could use a similar sized piece to patch it up. I always keep broken glassware for this
reason. You will have to be more careful though when heating or cooling the repaired condenser, as it is much more likely to fracture.
|
|
Lambda-Eyde
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 859
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
No you can't, unless you're skilled in glassblowing and have access to an annealing oven. A piece of glassware is not ready for use until it's been
annealed, no exceptions.
Anyways, you're describing your problem too vaguely. It's difficult to answer considering how your question is formulated.
If it's a simple liebig condenser without joints, buying a new one shouldn't set you back much.
This just in: 95,5 % of the world population lives outside the USA
You should really listen to ABBAPlease drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
Nitrator
Harmless
Posts: 27
Registered: 29-9-2012
Member Is Offline
Mood: No Mood
|
|
You certainly can if your skilled enough, but like I said, you have to heat/cool it very gently and reduce as much physical stress as possible. In
all likely hood, you will probably fail or it will only last a little while. But it's worth a shot. ![;)](./images/smilies/wink.gif)
Btw, when you buy a new condenser, (you'll have to eventually for sure) don't pay more than 20 bucks for it.
|
|
Endimion17
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1468
Registered: 17-7-2011
Location: shores of a solar sea
Member Is Offline
Mood: speeding through time at the rate of 1 second per second
|
|
Take a photo and let's have a look.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2689
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
If the top is not jointed, just cut the tube shorter, if there is enough tube left, and let it be short. The main thing is to not have a crack left
in the glassware, as it will propagate eventually. Same for water inlets and outlets, I have used many condensers with chipped or shortened water
tubes, as long as there is enough to wire a tube to, it is OK, although I try to never leave water running for long times unattended in those. Just
cut off broken pieces, and fire polish the new edge if you can, or at least sand it with a piece of fine black sand paper.
If you look in most any college organic lab you will see research being done with mostly older glassware, much scratched, chipped, and/or repaired.
Minor scratches and small chips are not a big hazard as long as they don't weaken the glassware. However, you should throw out or repair any cracks,
with star cracks being easier to repair, larger straight ones rarely are fixable. But broken off tube connectors are common, and if on the outside of
the piece, often are fixable.
[Edited on 1-10-2012 by Dr.Bob]
|
|
elementcollector1
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
How does one cut off the top evenly? I don't have a glass inscribing tool.
Photos are coming, camera's busy charging.
So, on the top of the condenser, a huge chip has been taken off the connector, about 2" by 1".
If I cut the afflicted area off, will it still work well as a condenser?
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
Endimion17
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1468
Registered: 17-7-2011
Location: shores of a solar sea
Member Is Offline
Mood: speeding through time at the rate of 1 second per second
|
|
The same way larger glass tubing is cut. After all, the condenser is a bunch of tubes. But it will be easier to tell if someone beside a flameworker
could fix it after we see the photos. If the broken part is too close to the condenser's cooling body, I think there's nothing you can do anymore. It
would be too complex and would require annealing.
|
|
zed
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
The way I remember it, broken glassware ends can be roughly shaped by means of metal "screen door" type screen.
|
|
smaerd
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1262
Registered: 23-1-2010
Member Is Offline
Mood: hmm...
|
|
if only the top joint is broken off it can still be used for reflux.
|
|
cal
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 88
Registered: 7-2-2012
Member Is Offline
Mood: No Mood
|
|
Glassware repair
I have been using this company for two years now and they have been able to repair everything from a three neck 3000 ml flask to a Graham condenser.
http://www.specialtyglassinc.com/ Talk to Pam about time frames due to their being busy.Toll Free: 800-899-2137
|
|