Kiwichemicali
Harmless
Posts: 19
Registered: 22-6-2011
Member Is Offline
Mood: No Mood
|
|
Distillation of drain opener and the use of Krytox LVP vacuum grease.
Last weekend I distilled drain opener.
Vacuum of 100mbar was applied to keep the temperature within ranges I feel comfortable with.
All joints were greased with Krytox LVP.
To prevent bumping I threw a few PTFE stirring bars in the source RBF. That works great because the stirring bar surface is rough enough. PTFE boiling
chips don't work because they start to float when the drain opener heats up.
An Hempel column was used as condenser, the sulfuric acid vapour is hot enough to condense using passive cooling.
Distillation went well, no foaming. The drain opener I used wasn't black but did contain impurities. When heated it turned light brown and during the
distillation it shifted to light yellow.
At first some water came over. When the sulfuric acid started to drip I stopped the distillation to throw away the first distillate. The difference
between the condensing of water and the condensing of sulfuric acid is easy to see. End result was clear concentrated sulfuric acid.
The only thing I was disappointed about was the chemical inertness of the Krytox LVP. It did withstand the cooled acid but not the hot vapours. It
turns black, however I was still able to separate the joints when the distillation was done but grease wasn't greasy anymore on the joints that came
into contact with the hot vapours.
If anyone has suggestions for a better grease? Maybe one of the other Krytos greases?
I'm not to happy with PTFE sleeves because it's difficult to use them and still get a leak free setup.
Kiwi.
|
|
|
woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
You now have some conc. sulphuric acid. Use that as 'grease' for sealing the joints. This is used in many types of distillation where very corrosive
chemicals are distilled.
|
|
|
Kiwichemicali
Harmless
Posts: 19
Registered: 22-6-2011
Member Is Offline
Mood: No Mood
|
|
Thanks, I'm aware of the possibility to use concentrated sulfuric acid as a lubricant. However that doesn't work for the distillation of the acid
itself.
Kiwi
|
|
|
woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Why doesn't that work for the distillation of the acid itself? The lubricant assures that the joints to not get stuck together and it assures that no
vapors can escape. Especially in your situation this may work well, because you already have some concentrated acid. If you want to distill more, then
you can sacrifice a very small amount of the acid you have now as a lubricant.
|
|
|
Heuteufel
Harmless
Posts: 25
Registered: 5-11-2011
Member Is Offline
Mood: No Mood
|
|
I really cant recommend concentrated sulfuric acid as "grease"! Already at room temperature its viscosity is much too low for it to be a good grease.
At elevated temperatures sulfuric acid is not any more viscous, than plain water. Result: the joints tend to leak and are difficult to seperate
afterwards. If you use a good quality of silicon based grease (I like the high-viscosity grease from Baysilone®) you will have no problems.
[Edited on 13-9-2012 by Heuteufel]
|
|
|
Mailinmypocket
International Hazard
Posts: 1351
Registered: 12-5-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Heuteufel  | I really cant recommend concentrated sulfuric acid as "grease"! Already at room temperature its viscosity is much too low for it to be a good grease.
At elevated temperatures sulfuric acid is not any more viscous, than plain water. Result: the joints tend to leak and are difficult to seperate
afterwards. If you use a good quality of silicon based grease (I like the high-viscosity grease from Baysilone®) you will have no problems.
[Edited on 13-9-2012 by Heuteufel] |
I have used a VERY small amount of sulfuric to make an airtight seal in glass joints while distilling bromine and nitric acid, none has ever seeped
out... It does require more careful handling though.
High quality silicone grease is good and safe, I have only had problems with SO3, in which case conc. sulfuric is best.
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
I have used conc. H<sub>2</sub>SO<sub>4</sub> for grease in many HNO<sub>3</sub> distillations at woelen's behest.
It works like a charm to seal the joints. It's viscosity is not an issue, IMO.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
watson.fawkes
International Hazard
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Heuteufel | | Already at room temperature its viscosity is much too low for it to be a good grease. At elevated temperatures sulfuric acid is not any more viscous,
than plain water. |
Viscosity is more of a requirement when the ground glass seals are out of tolerance than
when they mate well. In an ideal situation, the average height of the gap between mating surfaces is only a few microns. It's why you only need a very
little bit of sealant on high-quality joints. On the other hand, if the mating surfaces are out of conicity (the property of being shaped like an
ideal cone), you could get gaps 100 times as large. In those situations the viscosity of a sealant matters much more. As always, the larger
ΔP is, the more force on the sealant there is, so what might work for atmospheric distillation, say, might not work for vacuum distillation.
Evidently taper grinding tools used to be standard in trade and available mounted on handles for field honing operations (touch up). I haven't seen
them for sale as new stock, however.
My guess as to why sulfuric acid works well as a sealant is how hygroscopic it is. It would expand a bit at either or both the leading and trailing
edge of the seal, providing a bit of mechanical force. Diffusion through a microns-thick fluid layer, however, is quite slow, so an almost-steady
state is quickly reached and the seal has long stability.
|
|
|
woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I have no experience with vacuum distillation, but with normal air-pressure distillations I have really good experience with H2SO4. I used it for
bromine and HNO3, but also for higher boiling compounds, especially apolar solvents. I never had joints which were stuck to each other. I use VERY
little amounts. Just enough to wet the joint, you can easily see whether all of the joint is wetted or not.
I also have used paraffin-butter for sealing joints. This also works well, but it is more work to cleanup. With conc. H2SO4 I just rinse my glassware
with tap water and do a final rinse with a small amount of distilled water and then allow the glassware to dry. In this way it remains perfectly clean
and no residues remain on and near the joints.
|
|
|
Kiwichemicali
Harmless
Posts: 19
Registered: 22-6-2011
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by woelen | | Why doesn't that work for the distillation of the acid itself? The lubricant assures that the joints to not get stuck together and it assures that no
vapors can escape. Especially in your situation this may work well, because you already have some concentrated acid. If you want to distill more, then
you can sacrifice a very small amount of the acid you have now as a lubricant. |
I did try it in the distillation I described above. Unfortunately it doesn't work for the relative high temperatures that are needed when distilling
sulfuric acid at 100mbar. At room temperature the joints move fine when 'greased' with concentrated sulfuric acid but when the distillation was
finished they were stuck and I was lucky I could take them apart after some heating.
Kiwi
[Edited on 14-9-2012 by Kiwichemicali]
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
A couple of glindemann rings on the cone might be more suitable for vacuum work than a viscous liquid . . .
|
|
|
Endimion17
International Hazard
Posts: 1468
Registered: 17-7-2011
Location: shores of a solar sea
Member Is Offline
Mood: speeding through time at the rate of 1 second per second
|
|
I never had any problems with sulphuric acid lubrication for atmospheric pressure distillations. It works fine, but the point is to use very little
near the top of the joint. It's hygroscopic, and the smear increases in size as the distillation progresses. If the joints are even and high quality,
it's fine.
Vacuum distillation is another thing. Even with high quality joints, air gets inside at elevated temperatures because the viscosity drops down. I'd
recommend fluorinated greases for such distillations, if the material is very corrosive.
Regarding the distillation of the acid itself, I just hope no one will try to run water through the cooler. Distillation produces roughly 98% acid
which boils at around 337 °C. The temperature difference is greater than 150 degrees, which is roughly the maximum recommended tolerance for
borosilicate coolers. Using water is not neccessary and increases the chance of the expensive piece of glassware breaking into pieces, not to mention
how dangerous it would be for the worker.
Air cooler is enough, as well as an empty Liebig cooler, too.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
