| Pages:
1
2 |
ScienceHideout
Hazard to Others
Posts: 391
Registered: 12-3-2011
Location: In the Source
Member Is Offline
Mood: High Spin
|
|
OTC tert-Butanol
Hi! I just saw a post on here that said that a member got t-BuOH from the octane booster "turbo octane booster 108."
Once I read this- I hopped in the car and drove to the autoparts immediately and bought a bottle. :-)
The member says that they took it and mixed it with water and shoved it in the freezer. They say they then decanted the non-frozen stuff and kept the
tert-Butanol crystals.
I have a bit of t-BuOH... I know it forms jellyish crystals just below room temp... In fact, my vial is usually about half-jelly.
I did a couple extra steps... I poured the fluid into a sep funnel and shook it with a bit of H2O (1/2 the volume of the booster).
I then drew off the bottom layer... It smelled sort of rubbery- similar to pure t-BuOH. However it was not flammable (I tested).
5 minutes in centrifuge to ensure it separated.
Into the freezer- 30 minutes- I saw no BuOH crystals... ?
What did I do wrong? Should there have been additional steps to purify it? Is there an alternative way?
I've seen it elsewhere online that says this brand I used contains tert-Butanol...
hey, if you are reading this, I can't U2U, but you are always welcome to send me an email!
|
|
|
Rogeryermaw
National Hazard
Posts: 656
Registered: 18-8-2010
Member Is Offline
Mood: No Mood
|
|
http://bluemagicusa.com/bm_files/msds/Turbo%20108%20Octane%2...
says kerosene, Methylcyclopentadieyl manganese tricarbonyl, and 1-5 percent of an undisclosed mixture which, even if it was tert butyl alcohol,
wouldn't be worth the trouble for that amount at the price per bottle.
|
|
|
Wizzard
Hazard to Others
Posts: 337
Registered: 22-3-2010
Member Is Offline
Mood: No Mood
|
|
That was me  And I am uncertain of my success... What I had seemed to have the
right properties, but I ruined the whole batch trying to dry it with a salt.
My process was trying to use the properties of the t-butyl alcohol and water at temperatures- I know it's water soluble more than other things, so an
amount of it would be stuck in the water as it froze, but most of the other parts of the gasoline additive were not able to be frozen, so it could be
decanted. Then I tried to separate the t-butyl alcohol from the water... I had some being distilled, but it did not come out well I had put the project on hold until I was able to source some actual t-butyl to
compare with my results from the Turbo 108.
[Edited on 8-30-2012 by Wizzard]
|
|
|
Wizzard
Hazard to Others
Posts: 337
Registered: 22-3-2010
Member Is Offline
Mood: No Mood
|
|
Also, the govt's MSDS for Turbo 108 lists different CAS numbers:
http://hpd.nlm.nih.gov/cgi-bin/household/brands?tbl=brands&a...
|
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
Does that mean I will not be able to make potassium metal after all?
And what of distillation?
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
|
Wizzard
Hazard to Others
Posts: 337
Registered: 22-3-2010
Member Is Offline
Mood: No Mood
|
|
Heating over a temperature controlled hot plate in an RBF with a large watercooled condensor, coping to evaporate more tbutyl than water, then repeat
the process to get a usable amount.
|
|
|
Rogeryermaw
National Hazard
Posts: 656
Registered: 18-8-2010
Member Is Offline
Mood: No Mood
|
|
http://hpd.nlm.nih.gov/cgi-bin/household/brands?tbl=chem&...
from the same site as the msds wizzard found, the other products by the same company that contain t-butanol all fall in at under 5%. the percentage in
the octane booster is not even listed. i'm not saying that it is not possible but that it may not be a viable route. at any rate, many of us would
love to have a reliable source of it so good luck and let us know what happens.
|
|
|
Squall181
Harmless
Posts: 46
Registered: 21-2-2011
Member Is Offline
Mood: No Mood
|
|
Is there any practical way to take T-butyl ether and make T-butanol form it?
T-butyl ether is found in a OTC product called start your engines.
|
|
|
Wizzard
Hazard to Others
Posts: 337
Registered: 22-3-2010
Member Is Offline
Mood: No Mood
|
|
Looks like it's MBTE, which is found in a few products. "Start your Engines" contains from 0-60% of it, by an MSDS I'm reading now.
"Methyl tert-butyl ether (MTBE) degradation by ferrous ion-activated persulfate oxidation: feasibility and kinetics studies."
http://www.ncbi.nlm.nih.gov/pubmed/19691249
|
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
Is there any way to turn MTBE into T-butanol?
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
|
hames
Harmless
Posts: 24
Registered: 14-2-2012
Location: oz
Member Is Offline
Mood: as was
|
|
I have almost pure tert-butanol which freezes in the refrigerator but doesn't seem to freeze specifically at temps under 25 degrees unless
refrigerated,I'm not sure the exact purity but I'm guessing its over 95% because it all freezes and there's no liquid left over.
Anyways as most people want it for a catalyst for the synthesis of potassium I'm willing to help fellow aussies out who seem to be having a hard time
obtaining it,I have a bit over a litre of it and I'd be willing to flog off a few 100ml bottles or swap for some other reagents if anyones interested.
cheers jim
|
|
|
Dave Angel
Hazard to Others
Posts: 128
Registered: 22-3-2005
Location: UK
Member Is Offline
Mood: 0 K
|
|
The attached paper describes the (albeit, undesired) acid catalysed hydrolysis of the ether.
Attachment: McLoughlin et. al. MTBE hydrolysis.pdf (136kB)
This file has been downloaded 1018 times
Although this work was performed with low concentrations (that of potential ground water samples) it would seem that HCl is quite capable of effecting
the conversion to TBA.
Rate of hydrolysis reported as 1.22/h at pH = 1 and 80 °C
Might be worth some experimentation if MTBE is more readily available than TBA.
Additionally, wikipedia describes HBr and HI as more effective catalysts for ether cleavage.
|
|
|
sbbspartan
Hazard to Self
Posts: 61
Registered: 6-3-2012
Location: Minnesota, USA
Member Is Offline
Mood: DEAD (diethyl azodicarboxylate)
|
|
From reading several MSDS sheets for "Start Your Engines", it appears that it contains 3 chemicals. <a
href="http://www.hardwarestore.com/media/msds/126434.pdf">MSDS.</a>
Isopropanol - 0% to 20%
Xylene - 0% to 20%
T-Butyl Methyl Ether (MTBE) - 0% to 60%
I'm not the best chemist, but these could be fairly easily separated by simple or fractional distillation, right. Wikipedia (Yes, I know wiki isn't
the best source of info) says that Isopropanol boils at 82.5 C and Xylene boils at 140 C, while MTBE boils at only 55 C. These would be fairly easy to
seperate I think.
Then hopefully, you could use HCl for 'acid catalysed hydrolysis' of the MTBE. This forms Tertiary Butanol and Methanol according to <a
href="http://iav.broadbrushart.com/Douthitetal2002.pdf">This PDF.</a>
Here is the formula - C5H12O (MTBE) + H2O ---> C4H10O (TBA) + CH3OH
From here you could separate them out through distillation (methanol boils at 65C and T-Butanol at 82C), or through cooling down(since t-butanol
freezes at around 25C).
Would this work? I haven't been doing chemistry for very long so if this is has no chance of working just tell me. Would you even have to separate
out the MTBE from the other chemicals, or could you just add HCl direct to the mixture, then separate T-Butyl based on freezing point or something
like that? If it would work, that would be awesome since "Start Your Engine" is very readily available. Walmart carries it, as well as some local
hardware stores. Its fairly expensive at around $7 for 4 ounces, but if you only need a little its not bad. I might go buy some and try this later,
but right now I am pretty busy. Here comes some Potassium.
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
The isopropanol could maybe be removed by shaking with water. Some of the MTBE will be carried over, too. Anyways, if you only want to get the MTBE
out, fractional distillation with a short column should be facile.
I doubt MTBE can be hydrolyzed with HCl, HBr or HI without converting the t-butanol to the halide or even giving isobutene. Preparation of t-butyl
chloride is done by shaking t-butanol with aqueous HCl and leaving it for ~30 minutes or so IIRC. Cleaving the ether and preserving the t-butanol must
be done with a non-nucleophilic reagent and a reagent that won't dehydrate the t-butanol.
[Edited on 1-9-2012 by Lambda-Eyde]
This just in: 95,5 % of the world population lives outside the USA
Please drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
So... any suggestions for that non-nucleophilic reagent that can cleave MTBE for tert-butanol?
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
|
Dave Angel
Hazard to Others
Posts: 128
Registered: 22-3-2005
Location: UK
Member Is Offline
Mood: 0 K
|
|
Whilst HX may result in the tertiary haloalkane, it might be worth some experiments. I would not immediately rule it out on (albeit, educated)
speculation, unless we have some literature to the contrary. What about dilute H2SO4 under mild conditions (to favor
substitution)?
In addition to straight hydrolysis to TBA, I'd also be inclined to try for deliberate formation of the haloalkane, and then react with dilute, aqueous
NaOH at low temperatures over a long time, again, to favor TBA (substitution product) rather than isobutene (elimination product).
I realise the tertiary nature of the species is a driver towards elimination, but I still feel that there's no harm in trying a few conditions rather
than ruling these entire routes out. Even if the yield is low (say 20 %), with enough starting material, one could isolate a small quantity of TBA for
potassium production.
Wizzard (or anyone else for that matter) you don't happen to have a pdf of the paper you linked to do you? (Water Environ Res. 2009
Jul;81(7):687-94) - persulfate route also appeals given OTC availability.
Would also like to add this project to my list; any joy with a UK OTC source of MTBE anyone?
|
|
|
jon
Hazard to Others
Posts: 459
Registered: 11-1-2006
Member Is Offline
Mood: paranoid distrustful apprehensive
|
|
you know since hcl is such a poor leaving group you might have some success with that to yeild the chloride if you use accelerators like bromide or
lithium chloride salts and lowered concentrations and temperatures as these accelerators allow one to do.
i.e. milder conditions aloowing for both kinetic and thermodynamic control of this reaction.
just a hunch, expiriment is king.
with the chloride in hand it's a simple matter of boiling in water to reclaimm the alcohol.
said alcohol would have to be dry dry dry to get sucessful results in making Kt-buto
[Edited on 8-9-2012 by jon]
Give me librium or give me meth!
Patrick Henry....
|
|
|
jon
Hazard to Others
Posts: 459
Registered: 11-1-2006
Member Is Offline
Mood: paranoid distrustful apprehensive
|
|
oh and just buy some mbte next time it's not hard to find
Give me librium or give me meth!
Patrick Henry....
|
|
|
Dave Angel
Hazard to Others
Posts: 128
Registered: 22-3-2005
Location: UK
Member Is Offline
Mood: 0 K
|
|
In that case, would you mind posting some examples of which types of stores / in what types of products (brands definitely useful) you've been able to
locate MTBE for sale either in your OTC shopping experiences, or which sites you have found it freely available to the public online? I'm sure many of
us would find this information to be a useful addition to the thread as, without the starting material, we're not doing any experiments!
|
|
|
jon
Hazard to Others
Posts: 459
Registered: 11-1-2006
Member Is Offline
Mood: paranoid distrustful apprehensive
|
|
elemental scientific has mtbe
also try chemsavers.
elemental was formerly hagenow laboratories and is very open to individuals purchasing so is chemsavers.
Give me librium or give me meth!
Patrick Henry....
|
|
|
hyfalcon
International Hazard
Posts: 1003
Registered: 29-3-2012
Member Is Offline
Mood: No Mood
|
|
Apparently, at least in the registration FAQ, this company allows individuals to register. Check it out:
https://store.schoolspecialty.com/OA_HTML/ibeCCtpItmDspRte.j...
or:
http://compare.ebay.com/like/320945330818?var=lv<yp=Al...
[Edited on 9-9-2012 by hyfalcon]
|
|
|
Dave Angel
Hazard to Others
Posts: 128
Registered: 22-3-2005
Location: UK
Member Is Offline
Mood: 0 K
|
|
Quote: Originally posted by Dave Angel  | | Wizzard (or anyone else for that matter) you don't happen to have a pdf of the paper you linked to do you? (Water Environ Res. 2009
Jul;81(7):687-94) - persulfate route also appeals given OTC availability. |
I've managed to get a copy of the persulphate paper. Apologies for the poor quality and size of the scan, I was in a rush when I photocopied it (I
don't have access to neat electronic copies of journals, sadly):
Attachment: Chen et. al.pdf (1.1MB)
This file has been downloaded 1003 times
To summarise, it seems that MTBE is indeed broken down by activated persulphate, however the resultant TBA is subsequently, itself, broken down
further, so isolating the alcohol from a reaction mix using this process would be the challenge. In a batch process, work would be require to identify
exactly what conditions to use and where to stop the reaction to maximise yield.
I'm still yet to identify an OTC source of MTBE in the UK, so no in-lab progress on this from me for the moment.
|
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
Distill the mix so that tert-butanol carries over as a gas, driving the reaction to the right? use molar amounts of persulfate and MTBE? Just a few
guesses...
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
|
Nicodem
Super Moderator
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
I trully don't know what to think of a person who invests enough effort to make at least 4 replies on this topic, yet obstinately refuses to UTFSE.
UTFSE!
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
|
Dave Angel
Hazard to Others
Posts: 128
Registered: 22-3-2005
Location: UK
Member Is Offline
Mood: 0 K
|
|
| Quote: Originally posted by elementcollector1 | | Distill the mix so that tert-butanol carries over as a gas, driving the reaction to the right? use molar amounts of persulfate and MTBE? Just a few
guesses... |
Perfectly good guesses, however with stoichiometric amounts, as soon as some TBA is formed, the persulphate will start acting on it as well as the
MTBE. We end up with a mix of unreacted MTBE, TBA, and products of the decomposition of TBA - any CO<sub>2</sub> evolution likely to drive
the reaction of TBA.
In removing the TBA, as it forms, by distillation the difficulty encounterd would be that TBA boils at 82 °C and MTBE at 55 °C - a high enough
temperature to remove the product will also remove the starting material.
A possibility would be to use a hot, aqueous persulphate reaction mix and slowly drip the MTBE into it, allowing it to react and quickly distill off
in very small amounts. In my thought experiment, this gives the MTBE time to convert to TBA but not much time for the TBA to further decompose. Some
MTBE is still carried over, but so long as TBA isn't further degraded the product could be separated and the MTBE reused.
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
