freedompyro
holmes1880
Posts: 116
Registered: 16-6-2011
Member Is Offline
Mood: No Mood
|
|
Recovery of K2SO4 from K2SO4/H2SO4/HNO3
I was wondering if anyone knew of a way to recover some of the waste products of making HNO3 from a nitrate salt.
I happen to have use for these Sulfates of Potassium, Sodium, Strontium, etc... But I'm not sure how to purify them from the remaining H2SO4 and trace
amount of HNO3. Possibly just adding water to the solution and allowing it to evaporate slowly would create large sulfate crystals of decent purity
that could be filtered out?
|
|
kavu
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 207
Registered: 11-9-2011
Location: Scandinavia
Member Is Offline
Mood: To understand is to synthesize
|
|
You can concentrate the solution somewhat but not to dryness as H2SO4 is not a volatile compound. Upon cooling (in an ice bath) crystals of K2SO4 will
deposit and can be filtered. Further recrystallizations from water will improve the purity.
[Edited on 2-1-2012 by kavu]
|
|
Adas
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
Distill off the acids, crystals will stay. And they are probably (mostly) hydrogensulfates, not sulfates.
Rest In Pieces!
|
|
hissingnoise
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Heating converts bisulphate to sulphate - small point, but still . . .
|
|
Adas
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 711
Registered: 21-9-2011
Location: Slovakia
Member Is Offline
Mood: Sensitive to shock and friction
|
|
Maybe at around 350°C, but I am sure that boiling point of the acids is far lower than this
Rest In Pieces!
|
|
Bot0nist
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
337C for sulfuric, but anyways, just concentrate, cool slowly, and decant. Dissolve crystals in water and recrystalize. No need to distill sulfuric
acid to get patassium (bi)sulfate from the mix.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
Lambda-Eyde
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 859
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
Not according to garage chemist:
Quote: |
Sodium hydrogen sulfate gives off water when heated at 300- 500°C and turns into sodium pyrosulfate:
2 NaHSO4 -----> Na2S2O7 + H2O
|
Well, don't be so sure. Or at least make sure you're sure before saying you're sure - IE. google it or check Wikipedia before doing stupid mistakes.
Sulfuric acid boils (with some decomposition) at 337 degrees C.
This just in: 95,5 % of the world population lives outside the USA
You should really listen to ABBAPlease drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
hissingnoise
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Quote: |
Sodium hydrogen sulfate gives off water when heated at 300- 500°C and turns into sodium pyrosulfate:
2 NaHSO4 -----> Na2S2O7 + H2O |
Not in the presence of H<sub>2</sub>SO<sub>4</sub>, it doesn't!
|
|
hissingnoise
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Quote: | Sulfuric acid boils (with some decomposition) at 337 degrees C. |
One more small point ─ sulphuric acid boils @ ~290°C
It's the azeotrope that has a boiling point of ~339°C
|
|
woelen
|
Thread Moved 2-1-2012 at 08:03 |
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Moved from organic chemistry to general chemistry.
|
|
freedompyro
holmes1880
Posts: 116
Registered: 16-6-2011
Member Is Offline
Mood: No Mood
|
|
As K2SO4 has a melting point of 1069 °C... I think I'm safe to just heat the crap out of it in a pyrex flask with a propane burner and turn it off
when the H2SO4 stops subliming.
I found this on wikipedia:
"Potassium hydrogen sulfate or bisulfate, KHSO4, is readily produced by mixing K2SO4 with an equivalent number of moles of sulfuric acid. It forms
rhombic pyramids, which melt at 197 °C. It dissolves in three parts of water at 0 °C. The solution behaves much as if its two congeners, K2SO4 and
H2SO4, were present side by side of each other uncombined; an excess of ethanol the precipitates normal sulfate (with little bisulfate) with excess
acid remaining."
[Edited on 2-1-2012 by freedompyro]
|
|
hissingnoise
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Quote: | As K2SO4 has a melting point of 1069 °C... I think I'm safe to just heat the crap out of it in a pyrex flask with a propane burner and turn it off
when the H2SO4 stops subliming. |
- Look FP, I don't know how far you intend heating your flask, but 'heating the crap' out of a borosilicate vessel sure sounds pretty ominous to me!
And I don't know where you're getting your numbers, but anhydrous sodium sulphate has a melting point of ~886°C --- and the fully hydrated salt melts
at temperatures not much above 30°C!
Are you, perhaps, mixing up Fahrenheit and Celsius?
|
|
hissingnoise
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
And BTW, where on earth did you get the idea that H<sub>2</sub>SO<sub>4</sub> sublimes?
It simply evaporates, as do the other mineral acids!
[Edited on 3-1-2012 by hissingnoise]
|
|
freedompyro
holmes1880
Posts: 116
Registered: 16-6-2011
Member Is Offline
Mood: No Mood
|
|
All that information on boiling points was taken off the potassium sulfate wikipedia page.
With the boiling point of H2SO4 the borosilicate vessel should only reach 350-375C max. I had read somewhere before that H2SO4 didn't boil and just
started subliming giant clouds of toxic sulfuric acid mist as it nears it's boiling point. I guess that info is wrong, and the stuff actually SO3.
Kinda surprised the stuff actually boils. Never heated it quite that high before.
|
|
hissingnoise
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Quote: | And I don't know where you're getting your numbers, but anhydrous sodium sulphate has a melting point of ~886°C --- |
Ooops!
Quote: | As K2SO4 has a melting point of 1069 °C. |
My apologies FP; for some silly reason I'd assumed you were referring to the sodium salt melting-point.
So let's just agree to blame Lambda-Eyde for bringing sodium into the equation in the first place? ![:D](./images/smilies/biggrin.gif)
As to the fragility, or otherwise, of your flask --- you might get away with heating it to over 300°C, but any slight draught as it cools will almost
certainly cause it to shatter!
Borosilicate glass can actually be heated to ~500°C for short periods, but this requires a longish annealing process!
|
|
Pulverulescent
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 793
Registered: 31-1-2008
Member Is Offline
Mood: Torn between two monikers ─ "hissingnoise" and the present incarnation!
|
|
It's possible that I've posted this info as hissingnoise, at some time, but, in industrial nitration processes, when spent sulphuric acid needed only
to be reconcentrated after denitration, the sulphuric acid was boiled in silicon iron pots over a strong heat source!
Because of the relatively poor heat conductance of the metal, the pots sometimes failed catastrophically, dumping boiling acid into the furnace!
However, I've often reconcentrated sulphuric acid in heavy-walled casserole dishes without incident!
Quickfit RBFs are somewhat less replaceable . . .
P
|
|
Aqua_Fortis_100%
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 302
Registered: 24-12-2006
Location: Brazil
Member Is Offline
Mood: †
|
|
BR8805833A states that KHSO4 could be ppted as K2SO4 by adding ethanol to KHSO4 solution (it doesnt talk about other alcohols, but might work as well)
, since the equillibrium
2 KHSO4 <--> K2SO4 + H2SO4
is pulled to the right, because K2SO4 is much less soluble in ethanolic solutions than KHSO4.. Since alcohol dillution and K2SO4 ppting release good
amounts of heat, alcohol is gradually added (and with stirring) and temperature must be about room temp (~25°C) since otherwise the K2SO4 will ppt as
'pseudo-doble salt' K2SO4*nH2SO4 (where n is 1/3, 1/2, 3/4, 3/5, 3, 6/7, 4 or 6) and in this case you will have new mess to play with in order to get
pure K2SO4..
The patent deals with LOW TEMPERATURE recover of K2SO4 from chemical reactors ( KCl + H2SO4 ---> KHSO4 + HCl ), just to dont mess with high temp
corrosive acids in reactors.. The alcohol can be distilled and recovered and according with paper, only 2% of new alcohol must be added to make up
losses in closed system.
Of course if that is presumed to be adapted to spent nitration mixed acids, you have to get rid of residual HNO3/NOx (with will react with alcohol;
nasty), and still if dont react, it can ppt along with K2SO4 when adding alcohol.. This is the boring part (or maybe not if you actually want to
eliminate nitrate bringing it to high temp fuzzing flame of a evil heavy metal torch in glassware just be sure to sign first a proper insurance contract though.. )
"The secret of freedom lies in educating people, whereas the secret of tyranny is in keeping them ignorant."
|
|
Aqua_Fortis_100%
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 302
Registered: 24-12-2006
Location: Brazil
Member Is Offline
Mood: †
|
|
Today I was cleaning my homelab and found a somewhat old bottle containing some KHSO4 from spent nitrating mix and I know there was no (or might be
little) nitrate since in the procedure Ive gently boiled until NOx disapeared..
Tested the procedure of ethanol.
Added some water to the bottle.. You can see the large KHSO4 crystals in the bottom. (I had to break it since it formed a large mass of solidified
KHSO4).
![](http://i242.photobucket.com/albums/ff176/tnitrato/K2SO4/100_0265.jpg)
KHSO4 and ethanol (home cleaning grade - 92,8° INMP):
Ive heated somewhat the bottle and left it to cool to room temperature (A beaker was used as water bath to speed up that):
![](http://i242.photobucket.com/albums/ff176/tnitrato/K2SO4/100_0266.jpg)
Measured 100mL of alcohol; six ~10mL portions were added with stirring and between these additions, it was let cool (the temp doesnt change much..
After each adition, it was found with a thermometer in the bottle that the temp rose from 25 to max of only 27°C).. After the first addition,
crystals started to ppt:
![](http://i242.photobucket.com/albums/ff176/tnitrato/K2SO4/100_0267.jpg)
![](http://i242.photobucket.com/albums/ff176/tnitrato/K2SO4/100_0268.jpg)
After the fifth addition there was no more increase in ppt volume, so a last sixth portion of alcohol was added and then filtered.. Like before, the
remaining portion (~40mL) were used in ~10mL portions to wash the K2SO4 on filter:
![](http://i242.photobucket.com/albums/ff176/tnitrato/K2SO4/100_0269.jpg)
The mass of coulple of grams of free flowing white crystals of K2SO4 were dried, stored in plastic container, labbeled and stored.
![](http://i242.photobucket.com/albums/ff176/tnitrato/K2SO4/100_0274.jpg)
![](http://i242.photobucket.com/albums/ff176/tnitrato/K2SO4/100_0276.jpg)
A bit of this K2SO4 was dissolved in water and some NaHCO3 added. Not visible reaction...
So this would be a interesting way to recover potassium values from your spent nitrating mix.. And of course you could recover ethanol by
distillation, left behind H2SO4 (probably at some moment this could make some impurities like diethyl ether and such, but I dont know).. Or you could
give it another uses to filtered liquid (neutralizing some nasty high pH spills, or just use it as toilet cleaner..)..
EDIT: Unfortunatelly I cant tell the actual yield since I didnt knew the KHSO4 contents of spent nitration mix (As Ive said, this was made long ago,
and dont recorded the amount of material on label).. But the 'chem' feel was that given the amount of KHSO4 crystals, the yields were aceptable/good..
[Edited on 9-1-2012 by Aqua_Fortis_100%]
"The secret of freedom lies in educating people, whereas the secret of tyranny is in keeping them ignorant."
|
|
Pulverulescent
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 793
Registered: 31-1-2008
Member Is Offline
Mood: Torn between two monikers ─ "hissingnoise" and the present incarnation!
|
|
Peach Syndrome? ![:D](./images/smilies/biggrin.gif)
P
|
|
Bot0nist
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
I really hope it's contagious.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
Pulverulescent
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 793
Registered: 31-1-2008
Member Is Offline
Mood: Torn between two monikers ─ "hissingnoise" and the present incarnation!
|
|
Quote: | I really hope it's contagious. |
What? Pictures too big, so numerous, and taking up space better used? ![:P](./images/smilies/tongue.gif) ![:D](./images/smilies/biggrin.gif) ![;)](./images/smilies/wink.gif)
P
|
|
freedompyro
holmes1880
Posts: 116
Registered: 16-6-2011
Member Is Offline
Mood: No Mood
|
|
Very nice work. Thanks a ton Aqua Fortis!
|
|
Aqua_Fortis_100%
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 302
Registered: 24-12-2006
Location: Brazil
Member Is Offline
Mood: †
|
|
Im SMDB member since end of 2006, but have reading this great forum earlier..IIRC end of 2005..And I sincerelly hope to stay continuing as member,
helping and being help by the SMDB community.
From this time until today, in many threads I have read, noticed that there is a great trend: when someone did an experiment occasionally other
people ask for pics/videos/schemes for several reasons, most of all IMHO, to have better understanding of the experiment itself (the more exciting an
experiment is, the bigger the trend to people ask for pics).
You is the first one which I see that dont like pictures.
Whats wrong? The size of my pics (500x600) is well under the SMDB recommended max size, gives good visibility and you dont have to scroll any
horizontal bar to read this thread (unless your computer is disconfigured), what is a very tedious when happen in some threads. Also, I dont like to
post tiny 'click to enlarge' pics because when pics are many, is also too tedious to see every pic individually and takes an additional time of your
life..
Quote: |
taking up space better used? ![:P](./images/smilies/tongue.gif) ![:D](./images/smilies/biggrin.gif) ![;)](./images/smilies/wink.gif)
P
|
like this http://www.sciencemadness.org/talk/viewthread.php?tid=18419 ? A whole thread to speak about ... ?
Sorry. Hope you dont take this as an agressive revenge. I enjoy your posts Pulverulescent/hissingnoise (specially in energetics section), but you
should have to understand/agree that Im just defending myself, like anyone would do.
Peace and cheers.
Back to thread:
Hello freedompyro, thank you too, this thread was an inspiration to me to search and try out the recovery of K2SO4. Fert grade K2SO4 is substantially
more expensive than KCl (as K2SO4 is made from it) and is becoming more and more as agricultural potassium needs rises and sedimentary KCl deposits
are depleted.. And besides this, as K2SO4 can be used to make KOH/K2CO3, is interesting to not waste any K[+].
Has anyone more ideas on homelab uses for the spent alcoholic acid mix other than distill/use as toilet cleaner? Both ethanol and H2SO4 are very
useful substances to just throw off..And to distill one has to waste some energy... Direct uses are interesting to me.
[Edited on 11-1-2012 by Aqua_Fortis_100%]
"The secret of freedom lies in educating people, whereas the secret of tyranny is in keeping them ignorant."
|
|
Pulverulescent
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 793
Registered: 31-1-2008
Member Is Offline
Mood: Torn between two monikers ─ "hissingnoise" and the present incarnation!
|
|
Quote: | A whole thread to speak about ... ? |
Touché!
. . . Yes AF, it is the ever-pretentious, moi!
It was, though, in Misc., (a feeble defense?) and my smartass comment was intended as witty more than anything!
I enjoy all your posts too, BTW!
And you do take the trouble 'some' of us seem to find too time-consuming!
So all in all, I wouldn't have you change a thing!
P
|
|