Pages:
1
2
3 |
cyanureeves
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
i understand now why titanium is used for anode. as the mmo wears away,the titanium is exposed and titanium passivates when used as anode so it does
not conduct and therefore wont erode leaving only the mmo coating as conductior. this came to me as i was thinking of using the platinum coated discs
from my apple g3. any scratch on the disc will just give way to almost instant erosion, if it is even platinum.(damn freakin space bar on my apple
keypad sticks like crazy)
[Edited on 27-9-2011 by cyanureeves]
|
|
plante1999
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
My cell is going good but i think I will attemp Calcium chlorate cell soon , Dan2 does your anode made from tin/antimony solder make residu in the
solution ?
I will probaly make KClO3 but the kclo3 source I found cost my 7$ for 312g so it is a little to high.
I never asked for this.
|
|
dann2
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
The Tin Oxide Anode does not leave any residue but it appears to be no good at making anything even though it lasts a long time.
Dann2
|
|
ryan0713
Harmless
Posts: 15
Registered: 18-9-2011
Location: Duluth, GA
Member Is Offline
Mood: No Mood
|
|
I liked the article. I might try it.
|
|
cyanureeves
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
plante i am using hi-yield brand muriate of potash. it is dirty as hell with some red clay stuff but i have made chlorate with it before. you just
have to filter it and you get more than three pounds of it for your 7 dollars. something is wrong with my 5volt output wire because it gets too hot
too quick and too bad because as it gets hot and starts bubbling i can see it making instant chlorate plumes.i got one mean,mean,nasty punch out of
the wet anode when i had it on 5volts.
[Edited on 28-9-2011 by cyanureeves]
|
|
m1tanker78
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 685
Registered: 5-1-2011
Member Is Offline
Mood: No Mood
|
|
How will you deal with the calcium hydroxide buildup on the cathode?
Tank
|
|
cyanureeves
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
how about using ice melting salt?some have potassium chloride,sodium chloride,calcium chloride and urea.
|
|
plante1999
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
I will scrap it of in the solution time to time .
When y go see my cell it was realy acidic and a lot of crust was on the cathode....?
I never asked for this.
|
|
plante1999
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
I just started a KCl to KClO3 cell. Dan 2 : Why it does not make anything?
I never asked for this.
|
|
Chemistry Alchemist
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 403
Registered: 2-8-2011
Location: Australia
Member Is Offline
Mood: No Mood
|
|
Im sorry if its a bit of a change of subject but this forum post is on chlorates so i though i could quickly ask this...
What type of Oxidizing agent should be used to oxidize Calcium Chloride to Calcium Chlorate?
|
|
cyanureeves
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
ChemistryAlchemist isnt voltage what does that or is it amperage? speaking of amperage(ha ha), is amperage what makes my chlorate cell melt the epoxy
and cap? i am running of a computer power supply and have to use the 3 volt lead because the 5 volts will just get too hot after 2hrs. my electrodes
are about 1/2 inch apart. 3 volts is just too slow. i would like to run at 5volts but want to know if there is a way to drop the amperage on my 5 volt
leads? arent there inline amperage lowering thingamajiggers that can be added?my other cell is doing better with an old 6volt 250ma charger.somewhere
i saw that a person used a car battery charger with a nichrome heating element coil to reduce voltage. if one lowers voltage with a nichrome wire,wont
amperage drop too?
[Edited on 2-10-2011 by cyanureeves]
|
|
Chemistry Alchemist
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 403
Registered: 2-8-2011
Location: Australia
Member Is Offline
Mood: No Mood
|
|
On the wiki page it said that you can use a oxidizing agent...
"It can be formed by oxidation of calcium chloride by a strong oxidizing agent."
http://en.wikipedia.org/wiki/Calcium_chlorate
|
|
m1tanker78
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 685
Registered: 5-1-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by cyanureeves ![](images/xpblue/lastpost.gif) | [...]arent there inline amperage lowering thingamajiggers that can be added?my other cell is doing better with an old 6volt 250ma charger.somewhere i
saw that a person used a car battery charger with a nichrome heating element coil to reduce voltage. if one lowers voltage with a nichrome wire,wont
amperage drop too? |
Reeves, you can try adding some more space between the electrodes first. If that isn't an option, why don't you build another cell and connect it in
parallel?
Nichrome wire - any resistance, really - will dissipate (waste) some energy as heat. You might as well put it to good use by adding another cell in
parallel, IMO.
Tank
|
|
cyanureeves
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
ooh! thank you tank. you are certainly correct about the waste and i just happen to build another cell.parallel would be jumping from the neg in #1
cell to neg in #2 cell with a jumper wire and likewise pos to pos? i never would have thought of doing that even though i now recall reading your
post on a similar matter before. series would be neg from#1 cell to pos in #2 and neg in #2 cell to pos in#1 cell ?
|
|
Chemistry Alchemist
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 403
Registered: 2-8-2011
Location: Australia
Member Is Offline
Mood: No Mood
|
|
I just saw a video on youtube about making a 250ml solution of water with 90 grams of iodized salt and placing a 9 volt battery in the solution and
leaving it... it produces Sodium Chlorate... is this true? i know its made by electrolysis but can this method be true? Is it a safe method of making
it?
http://www.youtube.com/watch?v=AokqCrFqLWs
|
|
Steve_hi
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 196
Registered: 4-12-2010
Member Is Offline
Mood: No Mood
|
|
I guess the best way to find out is try it it's pretty simple i'm going to do it when I get back I like your you tube on producing Naoh by
electrolysis
|
|
Chemistry Alchemist
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 403
Registered: 2-8-2011
Location: Australia
Member Is Offline
Mood: No Mood
|
|
Yeah i guess i could check it out, no harm in trying i guess... can you over electrolysis it... if u know what i mean... yeah thanks for checking it
out ![:)](./images/smilies/smile.gif)
|
|
ScienceSquirrel
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline
Mood: Dogs are pets but cats are little furry humans with four feet and self determination!
|
|
I might be wrong as it is decades since I did any electrochemistry but;
According to this a 9V battery is good for about 300 to 600 mAh
http://data.energizer.com/PDFs/522.pdf
Let us assume that it is 600mAh ( best case scenario )
Then it will produce 2160 Coulombs
http://en.wikipedia.org/wiki/MAh
Using Faraday's 1st law
http://en.wikipedia.org/wiki/Faraday%27s_law_of_electrolysis
I make it that the best case yield is 0.79g of chlorine or 11 millimoles of molecular chlorine!
It requires 3 moles of chlorine to make 1 mole of sodium perchlorate so assuming 100% yield we would end up with around 1.17g.
|
|
nomcopter
Harmless
Posts: 3
Registered: 7-3-2022
Location: California, USA
Member Is Offline
|
|
Quote: Originally posted by woelen ![](images/xpblue/lastpost.gif) |
I made a very small 100 ml cell, which allows one to make 30 grams of KClO3 per day and which can be operated from a simple fixed 5 volt power supply,
which only needs to be capable of delivering 5A (the cell itself takes only 3 to 4 A, but using a 5 A power supply gives some headroom and allows for
tolerances in construction of the cell). Cost of the cell only is $30, excluding the power supply. |
Love the tutorial - and have had good success making one with a platinized titanium anode and a titanium cathode I made by bending a 12 gauge titanium
wire into a nice mesh. Why is it so important to remove the crystals with a plastic spoon? Are you worried about contaminating the product with metals
(a fuel) and that leading to a fire risk? Aren't they already contaminated with a fuel from electrode corrosion?
Started the recryst of my first batch, used 1.6mol of potassium chloride in a 250mL schott duran bottle and did 50 hours at 8A. This should have left
~80g/L of chloride left according to https://www.chlorates.exrockets.com/table54.html assuming 54% current efficiency. But all the chunks didn't dissolve until I'd boiled it in more
than a liter of water and boiling it in 1.5L still wasn't enough to make it a clear solution - it was still quite turbid and overall white.
Theoretically 1.6mol of potassium chlorate should dissolve in ~370mL of water. I can't imagine I have _that_ much perchlorate production. Perhaps it
is titanium dioxide contamination from corrosion of my cathode..?
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
The liquid is quite corrosive, and if you scrape the crystals out of the container with a metal spoon, then this might damage the metal spoon. It adds
additional impurities to the KClO3, and it spoils the spoon. No need to worry about adding fuel in the form of metal ions, but adding additional
impurities never is a good thing, hence the use of a plastic spoon.
If the liquid remains turbid, even at quite high dilution, then I'm quite sure that you have some contaminant in your solution. It might be TiO2 from
one of the electrodes, it also could come from the KCl you used. Sometimes, anti-caking agent is added to KCl, which is intended to be used as
salt-replacement. There also is KCl, intended to be used for melting snow on roads. This is used in places, where NaCl is too harmful for plants. Such
KCl, however, is impure and may contain MgCl2 or CaCl2.
I would just let all of the solid matter settle at the bottom and decant the clear liquid from it. The clear liquid then can be worked up for the
KClO3.
|
|
nomcopter
Harmless
Posts: 3
Registered: 7-3-2022
Location: California, USA
Member Is Offline
|
|
Aha you are totally right - it's tricalcium phosphate listed right on the bag as an anti caking agent. My electrodes looked pretty untouched I was
shocked at the volume of white fluff. Well at least hot-filtering/decanting is a lot easier when it is super diluted and then I can boil off the
excess. Thanks for the tip! Love your home science website - great explanations I've used it a lot for reference and to come up with fun ideas.
One change I recommend to your procedure is to make the holes in the cap by heating the tips of the electrodes with a blowtorch and then melting it
through. Ends up making a hole that is a perfect fit and is less dodgy than with a knife.
[Edited on 2023-8-9 by nomcopter]
|
|
Texium
|
Thread Moved 12-9-2023 at 11:49 |
Pages:
1
2
3 |