Pages:
1
2
3
4 |
niertap
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 76
Registered: 5-8-2011
Member Is Offline
Mood: hyper-conjucated
|
|
ATOMIC HYDROGEN
Ignorance is bliss
Outliers in life are modeled by chemical kinetics
|
|
The WiZard is In
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1617
Registered: 3-4-2010
Member Is Offline
Mood: No Mood
|
|
Why? Does it have some magic Hf?
Somewhere (I at the moment cannot put hands on it)
I came across a ref to 10 000o with O3 and Zr (?)
Hf (?) at 100 000 psi or some such.
Here is something to keep you busy.
MISSION IMPROBABLE
by
The WiZ (Donald J Haarmann)
You have been chosen lead pyrotechnist for the first peopled mission to Dubious 7. Your mission, should you choose to accept, is: supply a pyrotechnic
compound as a source of heat for cooking purposes. Because of the limited weight carrying capacity of the launch vehicle the reaction you choose must
have the highest possible ratio of heat produced to weight of reactants, i.e., kilo calorie/gram (K/cal/gm) of reactants. There are no restrictions on
the state of the reactants; they may be either solids, liquids or gases.
For those not familiar with the method of calculating the amount of heat produced by a reaction, the following explanation is provided.
The amount of heat in kilo calories is calculated by subtracting the heat(s) of formation [heat of formation is now called “standard enthalph of
formation”] (Hf°) of the reactant(s) from the heat(s) of formation of the products. This value is then divided by the weight of the reactants to
obtain heat per gram in kilo calories per gram.
Hf° prod (K/cal) Hfo react (K/cal) = Heat (K/cal)
K/cal
-------------
gms of reactants = K/cal/gm
The heat of formation is the amount of heat required to form one gram MOLEcular weight (mole) of a compound from its constituent elements. If heat is
liberated by the reaction the heat of formation has a negative value, i.e., the heat of formation of aluminium oxide Ai2O3 is 400.5 K/cal per mole
(102 grams) of aluminium oxide. That is, if we were to react sufficient oxygen and aluminium to produce 102 grams of aluminium oxide we would also
produce ( )400.5 K/cal of heat. Elements have a heat of formation of zero. Remember a negative value means heat has been produced.
Let us look at a simple reaction, such as the
burning of titanium in oxygen.
Ti + O2 = TiO2
One mole of titanium (47.9 gms) reacts with one mole of oxygen (32 gms) to produce one mole of titanium dioxide (79.9 gms). The heats of formation for
titanium and oxygen are 0, while the Hf° of titanium dioxide is 225 k/cal mole.
47.9 gms + 32 gms = 79.9 gms
Ti + O2 = TiO2
0 k/cal 0 k/cal = 225 k/cal
.
Hf° products Hf° reactants
------------------------------------- = heat produced per gram weight of
reactants
weight of reactants
( 225) (0 + 0) = 225 K/cal
-------------------------------------------------------------------- = 2.82 k/cal per
gram
(47.9 gms) + (32 gms) = 79.9 gms
A more complicated reaction:
3998.94 gms
1960.8 gms + 2038.14 gms
(16)(122.55gms) + (6)(339.69gms)
16KCIO3 + 6SbS3 --> 16KCI + 18SO2 + 3Sb2C4,
(16)( 93.5k/cal) (6)( 43.5) --> (16)( 51.6) + (18)( 71.0) + (3)(214)
( 1496 k/cal) + ( 261) --> ( 825.6) + ( 1278) + ( 642)
( 1757 K/cal) --> ( 2745.6 K/cal)
[reactants] [products]
988.6 k/cal
[products] [reactants]
( 2745.6 k/cal) ( 1757 k/cal)
-------------------------------------- = 0.25 k/cal gm
3999 gms of reactants
Now looking at these reactions and the way the results were obtained, two things will be obvious; first because the Hf° of the products is subtracted
from the Hf° of the reactants it will be useful to produce products with high Hf° using reactants with the low Hf°. Indeed the best results will be
obtained using reactants with either a low Hf° (small negative value), 0 (elements) or compounds with a positive ( + ) Hf°'s, of which there are not
many. (Remember minus a minus is a plus.) There are only few inorganic compounds with positive values of Hf° and are some what exotic e.g., fluorine
perchlo¬rate CIOF4, Hf° + 18.5, BrCI, + 14.6, N2O, + 19.49. Secondly, because the heat pro¬duced must be divided by the molecular weight of the
reactants, it would be wise to use products with low molecular weights. The reaction between hydrogen and oxygen or fluorine comes to mind, however,
these reactions produce only 3.2 K/cal/gm of heat despite their low molecular weights. These two reactions do, however, produce high specific
impulse, which makes these reactions useful in rockets, and such.
Heats of formation can be found in the CRC Handbook among other references [my reaction was obtained using products in the CRC Handbook. Most
libraries have a copy.
A final note; heat does not mean temperature, e.g., the reaction of oxygen with aluminium produces 3.9 K/cal/gm of heat vs. 3.6 for magnesium/oxygen,
the magnesium reaction is capable of producing a temperature of 3600°C, whereas aluminium can only produce a temperature of 3000°C. Indeed the
reaction between hydrogen and fluorine while only producing 3.21 K/cal/gm results in a temperature of 4030°C. In general the highest temperature
produced by a reaction can never exceed the boiling temperature of the most refractory reaction product when the reaction products are solids. The
highest value being approximately 4500°C (thorium oxide). The highest flame temperature for a reaction using gases is 4500°C for the reaction
between cyanogen (C2N2) and oxygen. For comparison the flame temperature for oxy/acetylene is 3140°C.
Originally published in PGII Bulletin 21. May/June 1987
Scanned 21vi97
The best result I have been able to obtain is -- 6 K/cal per gram of reactants. Can you do as well or even better? Using boron and ozone
2B + 2O3 3B2O2
(6) (10.8gms) (2) (48gms) --> 160.8 gms
-906 - (+68) = -974 K/cal
-974 K/cal
160.8
= 6.05 K/cal
Added [Well… I see in the late Dr. Ellern’s book a better reaction! One that will yield -13.4 K/cal per gram!!]
[I have doubts about cyanogen and oxygen producing a 4500oC flame temperature. I believe this is base on an old value for the boiling point of carbon,
e.g., 4500oC. 3600 oC is more likely.]
|
|
Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
Darn. Can't ask the WiZ what he found in Ellern now, and my copy is in storage 80 miles away.
In reference to the odd chemicals that were (or are being) offered at Skylighters going out of business sale, I've come across something interesting:
Attachment: Ti, Zr & Hf compounds as pyrotechnic fuels.pdf (1.1MB) This file has been downloaded 429 times
Zirconium diboride, Hafnium carbide, etc. All are usually considered highly refractive ceramics for extreme environments... But they burn.
Merely mixed straight out of the jar from chemical supplier with stoichometric ammounts of Potassium nitrate, these ceramics BURN. Not quite as hot as
the pure metals, but then, they don't go off from minor static discharges, bumps or mere dirty looks as the finely powdered metals do. I do not enjoy
handling fine Zr powders in particular, I have had a couple of near misses.
From a quick look at the tables in the attached paper- Hafnium carbide has a density around 12 g/cc, and burns somewhere upwards of 3,000 C? Al is
only around 2.7 g/cc. And it looks like the HfC is often supplied as particles verging on sub micron range? I can think of possible uses.
[Edited on 28-11-2017 by Bert]
[Edited on 28-11-2017 by Bert]
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
Pages:
1
2
3
4 |
|