briankim78
Harmless
Posts: 3
Registered: 9-3-2011
Member Is Offline
Mood: No Mood
|
|
Ampoule sealing inside the glove box
Ampoule sealing inside the glove box
Dear all,
I am preparing some chemical which is very reactive to the atmosphere.
Therefore, I am trying to put the material inside the glass ampoule and seal it while it is prepared inside the glove box.
The glove box I use is filled with Argon.
Any suggestions?
|
|
ldanielrosa
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 124
Registered: 25-4-2007
Member Is Offline
Mood: transparent
|
|
What precisely is it sensitive to? If exhaust from an oxyfuel torch with reducing flame is not an option, then maybe heat the ampule stem on a piece
of metal that you play a tig torch on.
Can you seal the top of the stem with epoxy in the glove box, the properly seal it by more mundane means once it's protected?
|
|
ScienceHideout
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 391
Registered: 12-3-2011
Location: In the Source
Member Is Offline
Mood: High Spin
|
|
I've sealed an apule of sodium, which is somewhat air reactive. I just put the oil in the ampule too. What if You fill the ampule with oil, add the
sample in the glove box, and seal it outside the box?
hey, if you are reading this, I can't U2U, but you are always welcome to send me an email!
|
|
UnintentionalChaos
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline
Mood: Nucleophilic
|
|
Quote: Originally posted by ScienceHideout ![](images/xpblue/lastpost.gif) | I've sealed an apule of sodium, which is somewhat air reactive. I just put the oil in the ampule too. What if You fill the ampule with oil, add the
sample in the glove box, and seal it outside the box? |
Because he doesn't want oil in his laboriously prepared compound?
Department of Redundancy Department - Now with paperwork!
'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
|
|
Arthur Dent
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
It might be much easier to do your ampoule sealing by gently blowing a stream of an inert gas like argon in the ampoule to displace the air as you're
filling it with your sensitive compound. Then while the ampoule is still fed with argon, seal it with a small torch.
Or is your compound so sensitive that it cannot even for a brief moment be exposed to air?
Robert
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
bfesser
Resident Wikipedian
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2114
Registered: 29-1-2008
Member Is Offline
Mood: No Mood
|
|
Put a rubber tube on the neck of the ampoule while in the glovebox and clamp it. Then remove from the glovebox and seal. Simple.
|
|
Contrabasso
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 277
Registered: 2-4-2008
Member Is Offline
Mood: No Mood
|
|
If this is to be a frequent need then look at the hot air guns used in solder rework stations. They are simply an electric heater which heats a stream
of gas to a "melts solder" type of temperature. Feed your argon through one and use it as a blowtorch. Use great care because the output IS flame hot
but it looks like just a stream of gas('cos it is!).
|
|
Heinrich
Harmless
Posts: 7
Registered: 14-3-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by bfesser ![](images/xpblue/lastpost.gif) | Put a rubber tube on the neck of the ampoule while in the glovebox and clamp it. Then remove from the glovebox and seal. Simple.
|
I've done this with highly air-sensitive materials, most recently with TiCl3. Works like a charm, but i have to admit that i was a little nervous
carrying at around. Probably the simplest and cheapest solution also.
|
|
redox
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 268
Registered: 22-2-2011
Location: The Land of Milk and Honey
Member Is Offline
Mood: Chalcogenetic
|
|
What exactly is your atmosphere-sensitive compound?
My quite small but growing Youtube Channel: http://www.youtube.com/user/RealChemLabs
Newest video: Synthesis of Chloroform
The difference between chemists and chemical engineers: Chemists use test tubes, chemical engineers use buckets.
|
|
quimica
Harmless
Posts: 4
Registered: 25-5-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by bfesser ![](images/xpblue/lastpost.gif) | Put a rubber tube on the neck of the ampoule while in the glovebox and clamp it. Then remove from the glovebox and seal. Simple.
|
I don't quite get it. How can one seal an ampule with a rubber tube atop of it? Wouldn't rubber be in your way or catch fire when you heat an ampule?
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Ampules have long necks, so you can seal the top with a septa or piece of rubber and still heat it below that a few inches and seal it. I did that
in graduate school and it worked fine. You can also get ampules with teflon type plugs which can then be sealed in a flame outside of the glove box.
There are also sealable shlenck type tubes that work fine for storing air sensitive compounds.
Bob
|
|