schatz
Harmless
Posts: 14
Registered: 15-12-2009
Member Is Offline
Mood: No Mood
|
|
Ignitor
I will be doing a bit of research into using smd resistors as bridge wire initiators and am looking at various ignitor compositions.
I understand that some electric munitions use kclo3+ Lead thiocyanate; And possibly Kclo3 + Potassium Ferricyanide.
I will be mixing only sub gram quantities at a time but was wondering about sensitivity issues since I have no experience with either compositions.
I was planning on using NC as binder dissolved in acetone.
|
|
Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
They are both quite sensitive to shock and friction. All the commercial igniters I have recently used avoid chlorates now. 20 years ago, I could
strike a commercial igniter on a safety match striker pad and it would fire. Or a tap with a hammer on a steel surface would cause one to explode-
Accidents with that class of mixtures were common.
I don't know what your intend use is, however those using resistors for model rocket igniters oftn use Copper oxide/Aluminum thermite. Plain old black
powder with a bit of Silicon or pyro Aluminum if you need more performance would work too.
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
pjig
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 155
Registered: 25-5-2010
Member Is Offline
Mood: always learning
|
|
What do you think they use then for commercial shells and class 1.3 items ??
I know most if not all commercial ematchs are covered with sleeve to protect the head(comp) from being touched.
|
|
schatz
Harmless
Posts: 14
Registered: 15-12-2009
Member Is Offline
Mood: No Mood
|
|
ignitor
Some commercial electric match heads I have seen and handled used the mentioned plastic sleeve and probably use Kclo3+Sb2s3. I could get them to go
off by direct friction or hammer blow ( with plastic cover off).
(My intended use is both as heat ignition and bullet hit effects.
In the past I have assisted historical re-enactment groups and amateur film makers, who even when they have expert technical help, cannot afford some
propriety devices. Some squibs, because of transport liabilities are frankly unaffordable.)
Ignitor
Oh !
Some eastern (chinese ?) e matches that went open circuit through storage, I witness being delicately dissected had what looked like a pale ( white )
composition inside. Could not have contained As, metal or carbon.
-={Please do not double post. Thanx: Moderator}=-
[Edited on 25-4-2011 by quicksilver]
|
|
Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
Schatz, for bullet hits used on an actor's body you need to restrict the amount of solid material that might be ejected from the explosion possibly
striking actors, crew, expensive camera gear- A resistor with heavy wire leads may become shrapnel. Professional body hits have very fine lead wires
with a small bridge wire and paper bodies.
For just setting something afire, plenty of others have used resistors. If you're going that route, safest to use the least sensitive first fire you
can and a hefty battery. The extremely sensitive and fast bridge wire/pyrogens designs are needed for scenarios involving limited output firing
systems and/or multiple matches in series that all need to ignite really fast before any element melts to break the circuit.
All the commercial igniters I use do have metal fuels. They are so fine that they're not easily visible in the composition of the match head.
I personaly installed about 8,000 igniters last year. I like them to be as insensitive as possible and still be reliable.
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|