metalresearcher
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 737
Registered: 7-9-2010
Member Is Offline
Mood: Reactive
|
|
How do you get high temperatures ?
For some processes (e.g. @Rogerywemaw's phosphorus furnace) you need high temperatures as for my sodium making and metal melting.
If you use high temp, how hot do you meed and how do you heat it ?
Do you have a furnace , propane / charcoal / wood/ electric arc ?
|
|
psychokinetic
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 558
Registered: 30-8-2009
Location: Nouveau Sheepelande.
Member Is Offline
Mood: Constantly missing equilibrium
|
|
Depends where exactly you need the heat.
If the entire environment needs to be hot, then a furnace is where it's at.
“If Edison had a needle to find in a haystack, he would proceed at once with the diligence of the bee to examine straw after straw until he found
the object of his search.
I was a sorry witness of such doings, knowing that a little theory and calculation would have saved him ninety per cent of his labor.”
-Tesla
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
Induction heater
|
|
Magpie
lab constructor
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Tim, can you provide a rough cost estimate for materials for a homemade 2000w induction heater. I'm just curious.
I've seen one of those in action at a university foundry and they are impressive. It was powered by 440V, 3-phase, IIRC.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
Under $400, depending on where you find parts and how much is surplus (aka junk).
The 440V 3 phase ones go way up there. How would you like a 1600A circuit?
Open a small steel mill with one that sized. ![:D](./images/smilies/biggrin.gif)
Tim
|
|
peach
Bon Vivant
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1428
Registered: 14-11-2008
Member Is Offline
Mood: No Mood
|
|
Induction won't be suitable for what he's doing. Neither will arcs.
Fire from wood or propane will work but basically you're after a resistive heating element. Like Silicon Carbide or Moly D if you want to roast the
ass out of piece of quartz or stainless tube.
Nichrome, Kanthal and the other nickel / chrome wires are possibilities. And far cheaper to try out since you can pull the wire from a toaster.
Two many posts asking the same thing, note the splattering effect in the replies. ![:P](./images/smilies/tongue.gif)
[Edited on 6-10-2010 by peach]
|
|
Texium
|
Thread Moved 19-11-2023 at 16:06 |