Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
 Pages:  1  ..  12    14    16  ..  28
Author: Subject: The short questions thread (1)
Panache
International Hazard
*****




Posts: 1290
Registered: 18-10-2007
Member Is Offline

Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein

[*] posted on 21-12-2008 at 16:29


Quote:
Originally posted by Rosco Bodine
Nitroethane could possibly be reduced to ethylamine.
Al amalgam or Al isopropoxide would probably do it.

Metaldehyde and ammonium nitrate would possibly react
giving a nitrate salt which could then be basified to
free the volatile amine. This is not something I have ever seen described
but there is an analogous reaction for methylamine.

These reactions could be hazardous, but manageable.

You would have to distill out the free amine and
absorb it in water.

[Edited on 17-12-2008 by Rosco Bodine]


Thats how i made it, i remember now. I used the nitrobenzene reduction reactions conditions using Sn/HCl in Vogel Vol 3 but using nitroethane, the ethylamine distills off from the horrendous reaction matrix at the end quite well. The aqueous solution can then be acidified and the Ethylamine.HCl crystallised and purified via recrystalisation, then basified using a minimum volume of caustic solution and distilling up a condenser running ~5C water then further up a NaOh pellet tower condensing the very pure ethylamine finally with ~-10 coolant or better still a dry ice condenser. If i recall correctly it was some >95% pure via gc. It took a couple of days but at the time was better than waiting for Sigma/Aldrich to ship via the slow boat (3months). Stores fine in the freezer at -20 with a good ground glass stopper, some silicon grease and an argon blanket. I only made ~50g this way so scaling it is anyones bet but i think the Sn reaction would be like NYE if it got too big.




View user's profile View All Posts By User
Panache
International Hazard
*****




Posts: 1290
Registered: 18-10-2007
Member Is Offline

Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein

[*] posted on 21-12-2008 at 16:41
Dry Box techniques.


So i'm new to this dry box game. Been doing some reading on it and using it i'm slowly getting the hang of it, as usual practice is about 200 times more valuable than theory. There are however some simple things which no-one ever seems to give advice on. At the moment there are two questions i have.
Firstly what is standard protocol for how long you leave the box after you open it to put something into it before it's considered 'dry' again. I am running argon in the box.
Secondly if i want to filter something that is in the freezer very cold and the crystalls i want to keep dry by the time i get it from the freezer to the dry box water has condensed a little on the vessel, then waiting for this to 'dry' in the dry box means the solution comes to temperature and the crystals re-dissolve a little. So its lose-lose, ha! Any tricks?
Maybe i need a freezer room with a dry box within it!!!




View user's profile View All Posts By User
sparkgap
International Hazard
*****




Posts: 1234
Registered: 16-1-2005
Location: not where you think
Member Is Offline

Mood: chaotropic

[*] posted on 22-12-2008 at 06:50


Quote:
...then can this also be true?

N,N'-dimethyl-o-phenylenediamine condenses with ketones and aldehydes to give rise to Schiff bases.


Best to try, I think, to be sure. Offhand, your diamine seems rather too hindered for me; if it reacts, the enamine ( >C=C-N<;) and not the imine (>C=N-) will form.

sparky (~_~)




"What's UTFSE? I keep hearing about it, but I can't be arsed to search for the answer..."
View user's profile View All Posts By User
Klute
International Hazard
*****




Posts: 1378
Registered: 18-10-2006
Location: France
Member Is Offline

Mood: No Mood

[*] posted on 22-12-2008 at 08:37


Panache, put your schlenk/flask in a sealed bag or similar with a dessicant inside before putting it in the freezer, then open the bag justbefore inserting the schlenk into the port, leave it under vacuum a while, and open it up.

I'm not familar enough with glove boxes to give you a detailed procedure. Are you talking of a true glove box, or a home built dry box? With a dry box, a few hours with CaCl2, eventually followed by an hour or two with KOH or even P2O5 should give you very dry atmospher, more than suitable for most needs.

Using a glove box, you will need to let is turn overnight to be sure you have minimum oxygen and humidity, we usually have the glow boxes continually on, even if we don't use them for more than a week, no need of ruining the catalysts for a little argon and the electricity for the vacum pump. Obviously this might not be an option for an occasional, personal use!




\"You can battle with a demon, you can embrace a demon; what the hell can you do with a fucking spiritual computer?\"

-Alice Parr
View user's profile View All Posts By User
Intergalactic_Captain
Hazard to Others
***




Posts: 228
Registered: 4-9-2004
Location: somewhere where i don\'t know where i am
Member Is Offline

Mood: frabjous

[*] posted on 22-12-2008 at 15:04


Anyone familiar with the Letts Nitrile Synthesis? Ar-COOH + KSCN -> ArCN +CO2 + KSH
http://en.wikipedia.org/wiki/Letts_nitrile_synthesis
Can't seem to find a mechanism, wondering if it would work with indole-3-carboxylic acid.




If you see me running, try to keep up.
View user's profile View All Posts By User
solo
International Hazard
*****




Posts: 3975
Registered: 9-12-2002
Location: Estados Unidos de La Republica Mexicana
Member Is Offline

Mood: ....getting old and drowning in a sea of knowledge

[*] posted on 22-12-2008 at 15:51


Letts Nitrile Synthesis

E. A. Letts, Ber. 5, 669 (1872).

Formation of nitriles by heating aromatic carboxylic acids with metal thiocyanates:





G. Krüss, Ber. 17, 1766 (1884); E. E. Reid, Am. Chem. J. 43, 162 (1910); G. D. van Epps, E. E. Reid, J. Am. Chem. Soc. 38, 2120 (1916); D. T. Mowry, Chem. Rev. 42, 264 (1948); F. Klages, Lehrbuch der organischen Chemie I (Berlin, 1959)




It's better to die on your feet, than live on your knees....Emiliano Zapata.
View user's profile View All Posts By User
brew
Hazard to Self
**




Posts: 96
Registered: 25-4-2008
Member Is Offline

Mood: enthralled

[*] posted on 22-12-2008 at 17:25


Does anyone know about the reaction conditions for the formation of Ethylenediamine via - and only via - electrolyses. Apparently Glysine as a copper salt is used and is converted to Ethylendiamine, and also 4-aminobenzoic acid-also as a copper salt is converted to benzidine. The information I have found for this is far from clear, other than the copper salts of these reagants were used. NO other details, I have looked pretty hard and assuming that it is something very unpracticle or just plain bullshit. If it isn't then I'd be interested in exploring perhaps the use of copper acetate with someother reagant containing a carboxy group. ie, AA"S Any help would be appreciated
View user's profile View All Posts By User
not_important
International Hazard
*****




Posts: 3873
Registered: 21-7-2006
Member Is Offline

Mood: No Mood

[*] posted on 23-12-2008 at 01:55


Sounds like a variation of the Kolbe electrolytic dimerization :
2 RCO2(-1) => R-R + 2CO2
this reaction generally doesn't work well with carboxylic acids that have electron releasing groups alpha to the CO2, alpha amino acids being one such. This indeed could be a case of a low yield reaction, references to it seem to date from the later 19th and early 20th century - http://tinyurl.com/85ybbs mentions it about half way down the right hand column - when there was a lot of examples of reactions giving a mishmash of stuff being described as making some particular compound.

The mixed reaction has been suggested a number of times with no success reported, although SFAIK without the use of copper salts.
View user's profile View All Posts By User
Intergalactic_Captain
Hazard to Others
***




Posts: 228
Registered: 4-9-2004
Location: somewhere where i don\'t know where i am
Member Is Offline

Mood: frabjous

[*] posted on 23-12-2008 at 07:59


solo - Thanks, but I've already followed out all those refs (except the german book) and found nothing of particular use. None of them speculate a mechanism.


Anyone know if Carolina Biological Supply sells to individuals? Failing that, any larger chemical suppliers that do?




If you see me running, try to keep up.
View user's profile View All Posts By User
Formula409
Hazard to Others
***




Posts: 129
Registered: 13-12-2008
Member Is Offline

Mood: No Mood

[*] posted on 23-12-2008 at 22:37


Aluminum Triiiodide preparation

1 mol Al turnings (or foil or powder all work well, powder is the quickest closely followed by foil then turnings a distant third) is combind with 1.5mol (note the excess of Al) of Iodine in 1000mL of cyclohexane (exchange solvent as needed but not diethyl ether!). This mix is stirred under reflux until the red colour has turned to a grey (about 1.5hrs with powder, 2-3 with foil, 4+ with turnngs). At this point the heat is turned off and the AlI3 in solvent allowed to cool to room tempeature with stirring.

Would Toluene be a suitable substitute in this reaction? What does "AlI3 in solvent" mean? The AlI3 is dissolved? How would it be claimed, surely they don't expect one to evaporate off 1L of solvent!

Formula409.
View user's profile View All Posts By User
brew
Hazard to Self
**




Posts: 96
Registered: 25-4-2008
Member Is Offline

Mood: enthralled

[*] posted on 24-12-2008 at 01:28


Thankyou not_important, yes I see what you mean by the amine and its lone pair and its possible effect towards the partially positive charged carboxyl carbon. This would inhibits its cleavage I'd imagine. I need to think through this stuff rather than just be looking for reactions and yields. It may be interesting to explore the effects of various pH values - Iso point ect- with such a reaction, and perhaps the effects of copper. Ive read somewhere about glycine complexing with copper, and it may be worth exploring.
View user's profile View All Posts By User
Klute
International Hazard
*****




Posts: 1378
Registered: 18-10-2006
Location: France
Member Is Offline

Mood: No Mood

[*] posted on 24-12-2008 at 02:53


Formula, there has been a post on that exact subject not logn ago, try using the search engine. Basicly, yes AlI3 is dissolved in the solvent (and yes, they could expect you to evaporat 1L of solvent, it is not uncommon, but they don't here: you directly use the AlI3 in solution). There were some questiosn about toluene being able to disproportioante in presence of AlI3, even though it might not be a problem, better use something like hexane.

Read the related thread.




\"You can battle with a demon, you can embrace a demon; what the hell can you do with a fucking spiritual computer?\"

-Alice Parr
View user's profile View All Posts By User
transformer
Harmless
*




Posts: 45
Registered: 30-6-2005
Member Is Offline

Mood: No Mood

[*] posted on 24-12-2008 at 04:39


Does anyone know good solvent system (and maybe an aproximate Rf value) with regards to performing a tlc on phenylacetone?



View user's profile View All Posts By User
DJF90
International Hazard
*****




Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline

Mood: No Mood

[*] posted on 24-12-2008 at 06:00


@ Formula409: If aluminium powder and iodine powder is mixed as a small pile on a heat proof surface, then direct combination of the elements can bt achieved by adding a drop of water. The reaction is quite vigorous, and gives off alot of iodine vapour, but a cold surface abouve the reaction mixture should cause the iodine vapor to solidify, allowing you to recover some of this loss. Iodine is easy to powder using a pestle and mortar (or some inprovised aparatus) - Aluminium should be used as a powder, but it should still work if you cut Al foil into very small pieces.

My own question: I am currently learning about wagner meerwein rearrangements and am happy in general with the course of things. One thing however does not make sense. If we take for example neopentyl bromide and force it to react under Sn1 conditions, then there is a 1,2-methyl shift. I am happy with this.

However the mechanism I have is not particularly revealing, and I cannot quite see how the cyclic transition state is formed (And where is the positive charge in this transition state? Is it delocalised? I dont understand this.) Can anyone help?

Merry christmas everyone

[Edited on 24-12-2008 by DJF90]
View user's profile View All Posts By User
Picric-A
National Hazard
****




Posts: 796
Registered: 1-5-2008
Location: England
Member Is Offline

Mood: Fuming

[*] posted on 25-12-2008 at 00:42


This is probably a very simple organic question for some.
Starting from TerePhthalic acid, Benzene-1,4-dicarboxylic acid, Would it be possible to nitrate the acid group comming of the fourth carbon?
If so would i be able to simply nitrate it and hope it goes to the fourth group?
My apologies if this is elementary, my knowledge on reaction mechanisms is very poor.
View user's profile View All Posts By User This user has MSN Messenger
Picric-A
National Hazard
****




Posts: 796
Registered: 1-5-2008
Location: England
Member Is Offline

Mood: Fuming

[*] posted on 25-12-2008 at 00:42


This is probably a very simple organic question for some.
Starting from TerePhthalic acid, Benzene-1,4-dicarboxylic acid, Would it be possible to nitrate the acid group comming of the fourth carbon?
If so would i be able to simply nitrate it and hope it goes to the fourth group?
My apologies if this is elementary, my knowledge on reaction mechanisms is very poor.
View user's profile View All Posts By User This user has MSN Messenger
kclo4
National Hazard
****




Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline

Mood: No Mood

[*] posted on 25-12-2008 at 18:47


Can the amines on amino acids be oxidized by Potassium Permanganate or Oxone (KHSO5) to nitro groups?
Also, does having the nitro group make it harder to decarboxylate or easier? The NO2 is very electronegative but I'm not to sure if that is even going to make much of a difference. I think it would make it easier to decarboxylate, but I haven't found any information on it, or on chloroacetic acids which i think would act similarly

If it is possible, seems like it would be easy to turn some of the smaller amino acids into Nitroacetic acid, and Nitropropionic acid. Might be kind of useful :)

powers gonna go out soon :(
View user's profile Visit user's homepage View All Posts By User
sparkgap
International Hazard
*****




Posts: 1234
Registered: 16-1-2005
Location: not where you think
Member Is Offline

Mood: chaotropic

[*] posted on 25-12-2008 at 19:55


kclo4:

With regards to oxidizing glycine, do take a look at this. I assume something similar might happen to larger amino acids.

Picric-A:

If you mean nitrating the benzene ring, you might have to resort to very harsh conditions to succeed because the two carboxyl groups will withdraw electrons from the benzene ring and make it less susceptible to electrophilic attack.

If you mean attaching a nitro group to the carboxyl group... I don't think you can, and I can't seem to find successful examples of such.

sparky (~_~)




"What's UTFSE? I keep hearing about it, but I can't be arsed to search for the answer..."
View user's profile View All Posts By User
texaspete
Harmless
*




Posts: 28
Registered: 26-7-2006
Member Is Offline

Mood: No Mood

[*] posted on 25-12-2008 at 23:04


Question: Can Bakelite be made by the home chemist?

I've found various threads mentioning that bakelite can be made form formaldehyde and phenol, but no threads describing the process. Wiki says says it requires high heat and pressure...
View user's profile View All Posts By User
not_important
International Hazard
*****




Posts: 3873
Registered: 21-7-2006
Member Is Offline

Mood: No Mood

[*] posted on 25-12-2008 at 23:54


Yes, if you are not out for a practical grade but just want to play with the process.

Mixing solutions of formaldehyde and phenol, with a molecular ratio of about 1.5:1, and adding a solution of NaOH to give a pH around 10, then warming to 60 to 70 C will give a prepolymer. Care must be taken to prevent thermal runaway of the reaction, else it will go too far.

This stage gives a still liquid if syrupy product. It would be mixed with wood flour (fine sawdust) and then heated to 120 to 130 C to complete the reaction to a thermoset plastic. The pressure was generally used to form or mold the plastic as it was reacting to set, just making small lumps wouldn't require that. Large amounts tend to overheat in their interior, cracking the piece, so slow heating and applied pressure would be needed for them.

A few old references. They state that pressure on the order of "50 to 100 lbs/sq-in" give a solid product rather than one containing bubbles or even being sponge-like. You can also use a bit lower ratio of formaldehyde to phenol, say 1.1:1, and then add a strong solution of HMTA to the resin to given enough additional formaldehyde to bring the ration up to 1.6:1 or higher. The HMTA decomposing on heating but stable enough at room temperature that more fluid resins can be prepared for use as coatings and such.


http://books.google.com/books?id=Vn1BAAAAIAAJ&pg=PA585&a...

http://books.google.com/books?id=X7OEAAAAIAAJ&pg=PA211&a...



[Edited on 26-12-2008 by not_important]
View user's profile View All Posts By User
Picric-A
National Hazard
****




Posts: 796
Registered: 1-5-2008
Location: England
Member Is Offline

Mood: Fuming

[*] posted on 26-12-2008 at 13:17


I was hoping to replace the -OH group with an -NO2 group, not add it on.
I dont see this working either to be honest.
Would it be possible to nitrate Benzoic acid and if so, what percentage of the Nitro group will go to the fourth carbon?
My aim is 4-nitrobenzoic acid by the way :)
thanks,

[Edited on 26-12-2008 by Picric-A]
View user's profile View All Posts By User This user has MSN Messenger
dann2
International Hazard
*****




Posts: 1523
Registered: 31-1-2007
Member Is Offline

Mood: No Mood

[*] posted on 26-12-2008 at 15:03


May be of some use:

A Bakelite + KClOx propellent.

Making the resol is relatively easy but if you want to make this king of propellent on a regular basis you need some sort of Vacuum pump
+ chamber and heater (inside the vacuum chamber). It is however possible to make a sstisfactory resol without a vacuum system but the resol takes a lot
longer to cure.
Note Phenol and Formaldehyde are poisonous and this procecure should be carried out in the open. Once the initial reaction is over and the syrupy
stage is reached then the stuff is relatively harmless (apart from flammability).

Method
Add 20g of Phenol and 0.5ml of 40% NaOH solution to 40ml of 37% aqueous Formaldehyde solution (Formalin). Bring to the boil and boil untill the liquid
becomes noticably thicker (typically in the order of 10 minutes). If you stop too soon it will take forever to cure the resin, if you wait too long it will beocme too
viscous to mix with the oxidizer (like toffee) or even become fully cured in whatever vessel you were boiling it in. You might be able to salvage it with alcohol.
The resol is removed from the heat and 108g of KClO4 or 125g KClO3 is stirred in. The resultant is poured or pressed into a mold/casing. Try your utmost
to get rid of bubbles at this stage. The grain is cured by placing
it in an oven at around 50C or so for about 12-24 hours. The temperature is slowly increased untill the resin sets rock hard at a final temperature of 120C or so.

If you increase the temperature too quick big bubbles will form in the grain.. The first cool part is mostly to allow excess water to evaporate., the actual curing
takes place at the higher temperatures. A resol that has been dried in a vacuum can be cured somewhat faster.
Never tried the above myself BTW.
Dann2
View user's profile View All Posts By User
kclo4
National Hazard
****




Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline

Mood: No Mood

[*] posted on 26-12-2008 at 15:04


sparkgap, thanks for the link but it seems to be oxidizing it further then I want.

I was thinking more so of turning glycine into nitroacetic acid. It seems that amines can be turned into NO2 easily with KMnO4 or Oxone and acetone (or just Oxone if it is an aryl amine) but I think the carboxylic group might interfere with that reaction.

Also, is something like Nitroacetic acid/nitroacetate easier to decarboxylate compared to acetic acid/acetate?
View user's profile Visit user's homepage View All Posts By User
Picric-A
National Hazard
****




Posts: 796
Registered: 1-5-2008
Location: England
Member Is Offline

Mood: Fuming

[*] posted on 26-12-2008 at 16:28


KClO4, why not make Nitroacetic acid from nitromethane (if nitroacetic acid is your desired product)
It seems very easy, http://orgprepdaily.wordpress.com/2008/03/10/nitroacetic-aci...
View user's profile View All Posts By User This user has MSN Messenger
kclo4
National Hazard
****




Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline

Mood: No Mood

[*] posted on 26-12-2008 at 16:49


Not in need of nitroacetic acid, just want to know if the NH2 on amino acids can be turned into NO2 for some other experiments I'd like to try eventually
View user's profile Visit user's homepage View All Posts By User
 Pages:  1  ..  12    14    16  ..  28

  Go To Top