Hang-Man
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 70
Registered: 16-1-2004
Location: Canada
Member Is Offline
Mood: Wasted
|
|
Detection of Hydrogen in Low Concentration
Suppose I have a gas stream that I suspect to contain hydrogen in ~0.1-1% concentrations. Can anyone think of a way to detect that hydrogen in a
semi-quantitative way without taking samples to a GC? Surely there is some metal oxide that could be reduced or some solution that would undergo a
measureable change on exposure to a hydrogen containing flow but I can not think of any.
I think my only play is electrochemical measurement with Pt electrodes but that will be irritating to set up and standardize.
Any ideas?
|
|
watson.fawkes
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
It's hard to have specific ideas for you without knowing what else is in the gas stream. A quite common way of detecting gasses is measuring the heat
generated by catalytic oxidation with a selective catalyst. All such devices I've seen have false positives and catalyst poisoning to worry about.
Detection thresholds can be quite low in the right circumstances.
|
|
Fleaker
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1252
Registered: 19-6-2005
Member Is Offline
Mood: nucleophilic
|
|
What else is in the gas stream? Perhaps try something with palladium sponge or foil or the like and get the amount of H2 adsorbed via mass. Just a
thought.
Neither flask nor beaker.
"Kid, you don't even know just what you don't know. "
--The Dark Lord Sauron
|
|
Hang-Man
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 70
Registered: 16-1-2004
Location: Canada
Member Is Offline
Mood: Wasted
|
|
The gas stream will contain primarily argon and small quantities of low molecular weight organic fragments. No oxygen. The theoretical maximum amount
of hydrogen per experiment is about half a mol non-uniformly emitted over a 90 minute period in an argon flow rate of ~100 sccm.
I'm beginning to think the only way is to take gas samples throughout the run and have them run on the GC. We don't have thermal conductivity detector
however which I believe is the best way to detect hydrogen. I guess I'll have them sent out
|
|
watson.fawkes
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
I don't know what your fixed-cost vs. variable-cost position is, but if you need to do this a lot and continuously you might consider a mass
spectroscopy. You'd heat a sacrificial fraction (quite small) of the gas stream with RF centered at the H<sub>2</sub> ionization energy
(to get preferential ionization) and then split the stream into three: non-ionized particles, H<sub>2</sub> ion, and the heavier ions.
This need only be partly quantitative, because all you care about is a single fraction. Calibration just for that fraction is substantially easier
than for everything. A calibration gas mixture can be mixed up from argon, hydrogen, and methane.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
At that concentration I think you could probably make a thermal conductivity detector from two broken light bulbs arranged in a Wheatstone bridge
circuit. Almost certainly worth a try.
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1314
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
http://www.kebaili.com/pd_khs100.cfm
http://www.qubitsystems.com/Merchant2/merchant.mvc?Screen=PR...
http://www.figarosensor.com/gaslist.html
There's three for you, just by searching ' Hydrogen gas sensor' on google. The Figaro sensors are usually fairly cheap.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
Hang-Man
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 70
Registered: 16-1-2004
Location: Canada
Member Is Offline
Mood: Wasted
|
|
Mass spec with the resolution required to detect hydrogen is certainly out of my price point. I only need to detect it once for proof of concept;
that would pay for a GC with a TCD.
I googled the hell out of hydrogen detection but only got safety related items and binary detection devices. I'm not sure if those will work, most
hydrogen detectors are geared towards detection in air, as illustrated by the mode of operation of the figaro sensor:
"These elements are installed into a “Wheastone Bridge”. A variable resistor should be adjusted so that the bridge will produce a stable baseline
signal when in an environmnet free of combustible gases. When combustible gases are present, they will be combusted on the detecting element, causing
its temperature to rise. Accordingly the resistance of this element will increase"
Although I will look into them further, I don't think they'll be suitable for a flow containing just H2 Ar and hydrocarbon fragments. The second one
may work, I'll have to look into it.
If I bubble the solution through an electrochemical cell I should be able to oxidize some of the gas to protons using Pt electodes and measure the
current? Any electrochemists in the room?
[Edited on 16-10-2008 by Hang-Man]
|
|
watson.fawkes
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
Quote: | Originally posted by Twospoons
The Figaro sensors are usually fairly cheap. | They're great little devices, but they all rely on selective,
catalytic oxidation in ordinary atmosphere with an excess of oxygen.
|
|
watson.fawkes
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
Quote: | Originally posted by Hang-Man
Mass spec with the resolution required to detect hydrogen is certainly out of my price point. I only need to detect it once for proof of concept;
that would pay for a GC with a TCD. | If only once, then disregard my suggestion. I was interested because
it's only about half of a full mass spectrometer. If you can use GC readily, just go do that. The extra work involved in any specific solution would
seem to mitigate against anything particularly fancy, especially since an off-the-shelf solution for what you're looking for doesn't seem to exist.
Quote: | If I bubble the solution through an electrochemical cell I should be able to oxidize some of the gas to protons using Pt electodes and measure the
current? Any electrochemists in the room? | I doubt you'll be able to discriminate hydrogen from the other
organic compounds, as there are plenty of other bonds in your system with less energy that the diatomic hydrogen bond.
|
|
Texium
|
Thread Moved 19-11-2023 at 12:39 |