HexJam
Harmless
Posts: 25
Registered: 29-9-2008
Member Is Offline
Mood: Steady
|
|
Plastic Chemistry Sets for a Student
Hi guys/gals
I'm just starting out on this chemistry madness thing and have enrolled on a home-learning course with a local college. The course is quite heavily
theory oriented, but I'd like to keep my hand in with the practical side of things and was considering buying a chem set to play with at home.
After some surfing I spotted some nice glass sets, but they were all quite expensive and I noticed some plastic sets that were much cheaper.
I was wondering, do you guys think these are any good or a waste of time/false economy? Also, what do you think I should be purchasing as to
constructing a good all round chem set (with a slight organic chem bias) for a begginer?
Thanks people!
HexJam
|
|
Maja
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 143
Registered: 27-2-2006
Member Is Offline
Mood: No Mood
|
|
If you are hooked really strongly, buying plastic set won't help you ! ) You will
be forced to buy glassware, but now ... You can just do experiments in jam jars etc... What kind of "practical chemistry" do you mean ?
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
Jam jars are good but are limited when it comes to heating; they usually crack quite easily. Just buying a few bits of proper glass will really help,
mainly a couple of beakers (I recommend 50ml and 250ml), an erlenmeyer/conical flask (125ml?) and some test/boiling tubes are pretty much essential.
Add to that a plastic (PP preferably) or glass funnel, and a spatula and you've pretty much got the basics for inorganic chem.
|
|
chemkid
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 269
Registered: 5-4-2007
Location: Suburban Hell
Member Is Offline
Mood: polarized
|
|
Through in a graduated cylinder and simple balance as well as SAFETY GLASSES! Also, if you want organic, some plastic tubing to run water through and
wrap around the top of a test tube to form a sort of condenser is useful.
Chemkid
[Edited on 29-9-2008 by chemkid]
|
|
vulture
Forum Gatekeeper
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
Plastic means you're forbidding yourself to do organic chemistry, as most organic solvents will dissolve your plastic set. It's good for aqueous
chemistry, but nothing else.
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
It also limits heating... How are you supposed to heat a plastic beaker on a tripod??
|
|
JohnWW
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2849
Registered: 27-7-2004
Location: New Zealand
Member Is Offline
Mood: No Mood
|
|
The best polycarbonates are supposed to be good up to 400ÂșC, and resistant to most solvents, except strong alkalis and acids that could cause
hydrolysis of the polymer.
|
|
Panache
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
Most chemistry based plasticware is polypropylene or high density polyethylene. For the purposes you describe (starting out adding a to b as
instructed etc) there is nothing that will harm the polymer as it is inert, the thing it doesn't like is heating above say 120-140C, which means
nothing warmer than this should ever be applied to it. So if you want to boil some water you will need to immerse a beaker in a pot of oil sitting at
140, which is slow but thats the cost of doing things in plastic.
I love lab plastic i use it extensively but i'm clumsy when bored and break so much glassware when washing it. 5L glass beakers cost a lot to drop if
glass and nothing if they are plastic.
A further note if you are contemplating using jam jars etc use the thinnest one possible as these are the least susceptible tot he thermal cracking
that is the demise of most soda glass based items. This theory can be tested by pouring boiling water into a room temperature fine thin stemmed wine
glass and doing the same to a jam jar. Just stand back when doing the jam jar.
|
|
Picric-A
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 796
Registered: 1-5-2008
Location: England
Member Is Offline
Mood: Fuming
|
|
You can buy polycarbonate beakers out there but from what i have seen it would be cheaper to buy a simple borosilicate beaker and a flask and a set of
ten test tubes. You can get all this from ebay.
I agree with maja though, start with jam jars until heating becomes absolutly neccesary.
|
|
HexJam
Harmless
Posts: 25
Registered: 29-9-2008
Member Is Offline
Mood: Steady
|
|
Hey, cheers for the replies guys, you've gave me lots to think about!
As for what I'll be doing with them, just basic lab skills stuff, practacing titration/distillation etc, just getting the basic techniques down. Just
I think that I'll probably help me remember/understand the course a lot more if I actually try out some of the experiments/techniques rather than just
reading/watching videos of them.
Right then, so far my shopping list is (I already purchsed some safety glasses!):
Graduated cylinder, Balance, Beakers (50ml & 250ml), Erlenmeyer/conical flask (125ml?), Test/boiling tubes, Funnel, Spatula. I must admit I'm
pretty tempted to just save up a little and make the investment for some glass stuff like (and maybe just get a few plastic pieces to compliment it)
I have a scales/balance in the kitchen that is apprently accurate to 0.1g that should be OK right? (Assuming I wash it afterwards ;-))
|
|
Picric-A
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 796
Registered: 1-5-2008
Location: England
Member Is Offline
Mood: Fuming
|
|
Quote: | Originally posted by HexJam
As for what I'll be doing with them, just basic lab skills stuff, practacing titration/distillation etc, just getting the basic techniques down.
|
If you wana practise titrations and distillation then you will need to get a burette and quickfit apparatus. Far from simple glassware...
Start small and when you decide you wana keep this hobby up get the equiptment.
Scales correct to 0.1g should be fine.
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
An alternative to quickfit is the "old skool" distillation glassware, with all the connections made with cork or rubber. This is satisfactory for some
work, but when distilling particular chemicals they can attack the seals and contaminate the distillate/produce a leak in your apparatus. Picric-A
gives good advice, wait till this is a serious hobby before you move into this sorta stuff.
|
|
ScienceSquirrel
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline
Mood: Dogs are pets but cats are little furry humans with four feet and self determination!
|
|
To attempt volumetric work you are going to need a serious balance accurate to at least .0.001g or better.
[Edited on 30-9-2008 by ScienceSquirrel]
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7997
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Have a look at this webpage about setting up a home lab. It describes what basic things you should buy for doing inorganic chemistry.
http://woelen.homescience.net/science/chem/misc/homelab.html
It also describes what chemicals you can buy to start with.
EDIT by woelen: Changed link, so that it works again.
[Edited on 12-6-12 by woelen]
|
|
chemkid
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 269
Registered: 5-4-2007
Location: Suburban Hell
Member Is Offline
Mood: polarized
|
|
.1 grams is great to start! (coming from the guy who used a triple beam balance with no magnetic balancer and that never gave the same weight twice
for most of his life).
But i really disagree with the use of jam jars. If i had started with jam jars, i would probably have a couple of burns right now...Reactions often
get hot unexpectedly, especially when your new to chemistry. (100 grams of aluminum and 300mL of concentrated HCl) If something gets to hot and goes
wrong, your probably don't want your glassware breaking on you and making the problem worse!
Chemkid
|
|