zbde00
Harmless
Posts: 25
Registered: 18-2-2005
Member Is Offline
Mood: No Mood
|
|
Reduction of carboxylic acid to alcohol!
Can anyone tell me a pactical and economical method to reduction of carboxylic acid to alcohol!
NaBH4+I2,LiAlH4,LiBH4 +TMSCl are expensive methods.
I have done NaBH4+H2SO4 method,but the yield is low(10%).
This is a problem worthy of heavy discussion.
Thanks in advance!
|
|
not_important
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
see https://sciencemadness.org/talk/viewthread.php?tid=2726&...
as well as electrolytic methods.
|
|
Swany
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 188
Registered: 11-4-2005
Location: My happy place...
Member Is Offline
Mood: Sanguine
|
|
NaBH4 will reduce some methyl esters cleanly to an alcohol, at least in the case of methyl 2,6-dibromoisonicotinate (80% yields, in abs. EtOH).
|
|
solo
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3973
Registered: 9-12-2002
Location: Estados Unidos de La Republica Mexicana
Member Is Offline
Mood: ....getting old and drowning in a sea of knowledge
|
|
.................or in 50% ethanol and water with 80+ yields and NaBH4.....which one can save the absolute alcohol for somethng else...........solo
It's better to die on your feet, than live on your knees....Emiliano Zapata.
|
|
zbde00
Harmless
Posts: 25
Registered: 18-2-2005
Member Is Offline
Mood: No Mood
|
|
Thank you!
To not_important
I have read this article.It use diethyl ether as the solvent.DME is dangerous in factory.
To Swany
My substrate is a carboxylic acid,not methyl ester.So your method should need two steps.This will cost much in factory due to much solvent and
purification.
To solo
I don't understand what you have said.Your meaning is that the solvent is 50% aqueous ethanol ?
|
|
Klute
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1378
Registered: 18-10-2006
Location: France
Member Is Offline
Mood: No Mood
|
|
Here is a fairly complete document on modifying borohydrides:
http://www.rohmhaas.com/assets/attachments/business/process_...
Thanks to Nicodem for sharing this.
You might want to try forming tdiborane with BF3.Et2O: it isn't too expensive, and is routinely used with apparently great yields in various diborane
reductions.
\"You can battle with a demon, you can embrace a demon; what the hell can you do with a fucking spiritual computer?\"
-Alice Parr
|
|
Nicodem
Super Moderator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
Refluxing carboxylic acids or their esters in diglyme with NaBH4 is said to work well. This way you don't need any additional reagent to form borane
in situ while diglyme is not a particularly expensive solvent. I'm quite sure the paper describing the method was already uploaded on this forum
somewhere, so search for it.
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
Barium
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 85
Registered: 24-8-2008
Member Is Offline
Mood: No Mood
|
|
1. It would help if you provided the proper information about the trials using diborane generated from sodium borohydride and sulfuric acid in order
to understand why it gave such low yields.
2. What is your substrate? How can you expect help if you can't tell us what you need help with? I assume the acid isn't the only functional group in
the molecule.
3. You mentioned factory in your replies to not_important and Swany. Are we to understand that a commercial entity wants free help from a bunch of
chem enthusiasts?
|
|
ziqquratu
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 385
Registered: 15-11-2002
Member Is Offline
Mood: No Mood
|
|
NaBH4 with I2 might do the job for you.
Attachment: NaBH4.I2 reduction and hydroboration.pdf (390kB) This file has been downloaded 7964 times
|
|
ScienceSquirrel
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1863
Registered: 18-6-2008
Location: Brittany
Member Is Offline
Mood: Dogs are pets but cats are little furry humans with four feet and self determination!
|
|
There was a bloke a while back that had thousands of gallons of water contaminated with hydrogen sulphide which he had to neutralise with potassium
permanganate.
Some of them have access to the Internet and that is about it, no books or journals of any consequence.
Others are distinctly cagey as they are do not want to give much away for commercial reasons.
|
|
zbde00
Harmless
Posts: 25
Registered: 18-2-2005
Member Is Offline
Mood: No Mood
|
|
To ziqquratu
I2 is expensive .
To ScienceSquirrel
Thank you.
I think dibrane may not be scaled up to 300L reactor.
Now I'm working on ZrCl4 +NaBH4 method.It is unfortunate that ZrCl4 is dangerous! When I weighed it, ZrCl4 fired due to the presence of some other
unkown impurities in the container.Anyone can tell me the reason?Some paper report TiCl4 +NaBH4 method.But TiCl4 is more dangerous!
I will tell the results using this method.
|
|
Nicodem
Super Moderator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
ZrCl4 can not "fire". It does not burn. All it does is fume a bit since it is a strong acid that hydrolyses in the presence of atmospheric moisture.
What you saw was probably just fog from the evolved HCl. Just keep it away from water. You can always use dry nitrogen atmosphere if the fog annoys
you. I take it that you are aware that you need to use dried THF (or whatever other solvent you will be using) or else you will get no conversion (if
you get anything at all since I don't remember if ZrCl4/NaBH4 even works on plain carboxylic acids).
PS: If you consider ZrCl4 and TiCl4 dangerous then perhaps you should consider changing profession. It is less acidic and less dangerous than AlCl3
which is regularly used in the industry in tons amounts without much problems. Also, using a forum dedicated to amateur chemists for your
job&profit related problems is… well, I don’t even know how to express myself…
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
Barium
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 85
Registered: 24-8-2008
Member Is Offline
Mood: No Mood
|
|
Diborane can be made in situ and then safely be used for reaction volumes of several thousands of gallons, if you know what you are doing. Diborane
will also give high to very high yields in the reduction of carboxylic acids to alcohols, if you know what you are doing.
Considering that you doesn't even know the properties of your reagents or seem to be unable to get that information, I highly doubt that you will be
able to scale up this reaction from lab scale to production scale without killing, at least, yourself. Do you even have a clue how the reaction
parameters change when you change reaction volume from 250 ml to 10 L to 300 L?
|
|
not_important
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Barium and others have made the important points that if you do not describe the starting substrate at least in terms of the functional groups
present, and all other constraints (no ether, one step, intended scale of reaction, can't cost much money), then you are not going to get good
answers.
Given what you have said, I agree with Barium that diborane based methods are likely the best choice for fine chemicals. On a very large scale with
simple substrates, catalytic hydrogenation is an alternative.
You state Quote: |
I have read this article.It use diethyl ether as the solvent.DME is dangerous in factory. | My reference
said di-ethyl, you say di-methyl ether - a gas at STP and a bit more difficult to work with. But both are used industrially.
As for what Nicodem ended with Quote: | ... Also, using a forum dedicated to amateur chemists for your job&profit related problems is… well, I don’t even know how to express
myself… | I do know what to say - asking amateur experimenters for free advice on manufacturing problems
is a very good way to get yourself and maybe your factory in the news as the latest industrial disaster.
Do yourself and your company a favour, hire industrial chemists/chemical engineers.
|
|
Barium
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 85
Registered: 24-8-2008
Member Is Offline
Mood: No Mood
|
|
Quote: | Given what you have said, I agree with Barium that diborane based methods are likely the best choice for fine chemicals. On a very large scale with
simple substrates, catalytic hydrogenation is an alternative. |
If using diborane is out of the question then I would make the methyl ester and reduce it to the alcohol with Ca(BH4)2. Methanol and some tosic acid
isn't exactly expensive. Neither are calcium chloride and sodium borohydride.
The equipment needed to handle the pressure requirements for the catalytic hydrogenation of -COOH --> -C-OH is expensive to say the least. But you
are correct in that it is the most economic route on a very large scale.
Quote: | Quote: | I have read this article.It use diethyl ether as the solvent.DME is dangerous in factory. | My reference
said di-ethyl, you say di-methyl ether - a gas at STP and a bit more difficult to work with. But both are used industrially. |
DME is generally the short name for dimethoxyethane or glyme, not dimethyl ether.
|
|
Swany
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 188
Registered: 11-4-2005
Location: My happy place...
Member Is Offline
Mood: Sanguine
|
|
As far as the methyl ester goes, why not just toss in some methanol and H2SO4, heat, then add NaBH4? Extremely crude, but....
EDIT: And what compound are you trying to reduce? That would help a bit. If you are using an amateur forum for professional work I would say we are at
least entitled to know the compound in question.
[Edited on 16-9-2008 by Swany]
|
|
zbde00
Harmless
Posts: 25
Registered: 18-2-2005
Member Is Offline
Mood: No Mood
|
|
To Barium
sorry.It's diethyl ether.I use wrong word.
To Nicodem
It is not the ZrCl4 burns,but is the impurities burn when contact with ZrCl4.
NaBH4+BF3.Et2O can product BH3 in situ.I will consider this method if I fail.
To others
I'm sorry.I have a feeling of crime because I use free resources for commercial use.
I come to this forum for some general idea(not for a detailed solution) like I go to a library or search internet by google.Companies can give
individual charities,but can individual give help to companies ?Companies's tax go to where?And I only a individual.I must finish my work.If I cann't
finish,I will be fired.I don't know whether you help me or help our company.
If someone can give me a perfect solution to my problem,I can give him money.Please contact me with U2U message.Thank you!
|
|
solo
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3973
Registered: 9-12-2002
Location: Estados Unidos de La Republica Mexicana
Member Is Offline
Mood: ....getting old and drowning in a sea of knowledge
|
|
Reference Information
Studies on Optically Active Amino Acids. V. Synthesis of Optically Active #945;-Aminoalcohols by the Reduction of #945;-Amino Acid Esters with
Sodium Borohydride
Seki Hedeo 1 Koga Kenji 2 Matsuo Hisayuki 3 Ohki Sadao 4 Matsuo Ichiro 5 Yamada Shun-ichi 6
Chemical & pharmaceutical bulletin Vol.13, No.8, pp. 995-1000,1965
http://www.4shared.com/file/27987730/72b2dc70/Studies.html
Abstract
A facile reduction of optically active alpha-amino acid esters and their hydrochlorides took place with sodium borohydride in ethanol or aqueous
ethanol to give the corresponding optically active alpha-aminoalcohols in fair yields. The reaction conditions were investigated.
-----------------------------------------------------------
...and a better method posted by chi from the WD forum/////
i fail to see how conversion to the ester and reduction of that is "better" than reduction of the free acid with 4-6 times less borohydride.
from Aldrichimica Acta 31(1), 19 (1998):
"Preparation of Zn(BH4)2
In a typical procedure, a 500-mL roundbottom flask, equipped with a magnetic pellet and fitted with a reflux condenser carrying a take-off adapter, is
flame-dried while a stream of nitrogen is passed through the system. The assembly is allowed to cool to room temperature while the flow of nitrogen is
maintained. Freshly fused ZnCl2 (18g; 125mmol) is added followed by NaBH4 (11g; 291mmol). 250 mL of dry THF is then added through a double-ended
needle and the contents are stirred at room temperature for 72 hours. The clear supernatant layer is used as such for reactions after estimating its
hydride strength (4.4 M in H–)...The reagent is stable over a period of 6 months when stored under nitrogen at room temperature."
from Synth Comm 26(4), 703 (1996) and one of the same authors as the above:
"A solution of zinc borohydride in THF was prepared by the metathesis reaction of sodium borohydride and zinc chloride as reported earlier. (Ind. J.
Chem., 1991, 30B, 1150.) After the completion of the reaction, the solution was allowed to settle and the clear supernatant liquid (0.28M in
borohydride) was used as such.
Initially, we reduced the amino acids with two equivalents of borohydride and quenched the reaction after 5 hours. The hydrolysis of the excess
reagent was very fast, unlike in the case of borane reductions, which require drastic conditions indicating that the excess reagent may not form a
strong complex similar to amine boranes which are well known to be quite unreactive. Therefore, we inferred that just one equivalent of borohydride
would be sufficient for the conversion of amino acids to alcohols. Indeed, we found that under stoichiometric conditions phenyl alanine was reduced to
phenylalanol in 87% yield.
In a typical procedure, phenyl alanine (5 mmol) was added to zinc borohydride (18 mL, 0.28M of borohydride in THF, 20 mmol of hydride). The reaction
mixture was refluxed for 5h and then quenched with MeOH. The residue was dissolved in water (10 mL) and NaOH (2g) was added and was stirred at room
temperature for 0.5 hours. The solution was then saturated with potassium carbonate and the layers were separated. The aqueous layer was extracted
with THF and the combined organic extracts were dried over anhydrous potassium carbonate. The solvent was removed under vacuum to yield 0.7g (87%) of
phenylalanol melting at 89°C (90-91)."
It's better to die on your feet, than live on your knees....Emiliano Zapata.
|
|
Nicodem
Super Moderator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
Quote: | Originally posted by zbde00
To others
I'm sorry.I have a feeling of crime because I use free resources for commercial use.
I come to this forum for some general idea(not for a detailed solution) like I go to a library or search internet by google.Companies can give
individual charities,but can individual give help to companies ?Companies's tax go to where?And I only a individual.I must finish my work.If I cann't
finish,I will be fired.I don't know whether you help me or help our company.
If someone can give me a perfect solution to my problem,I can give him money.Please contact me with U2U message.Thank you! |
Corporations give money for charity to get tax reduction and they pay taxes because they have to. This is all profit related behavior and there is no
move a corporation does without it being profit motivated. Have you ever heard of a company paying any of its damage to the society without a court
order or law threat? I hope you understand why most of us feel uncomfortable helping professionals who are paid for their work by companies most
likely part of some corporation that makes the life of amateur chemists and people in general more miserable that it should be. But if you want to
play this kind of game you can always make a donation to the forum. However, you don’t understand a very simple thing. There is no way anybody can
give you proper advice without knowing what kind of carboxylic acid you are trying to reduce. There is no method that is cheap, easy and general at
the same time. The process needs to be adapted to the specific substrate and the economic requirements. You did not bother even telling if it an
aromatic or aliphatic acid, what functional groups it contains and where…
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
zed
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Thank you solo! Nice reference.
Zebedee, I personally have no objection to your using this forum to garner information that you are going to use for commercial purposes. Money makes
the world go around.
As for I2 being expensive......I'm not sure it really is. Initially, it costs quite a bit, but It recycles pretty well. Oxidize your effluent,
recover the I2 crystals that form, and reuse them. They do it all over the world, but here in the US, it has become a must. I2 consumption,
especially excessive I2 consumption, may bring irritating government inspectors around.
For ease of running, with water as the solvent, NaBH4-NiCl2 is reported to do a good job on amino acids. Uses a lot of Borohydride though.
http://journals.tubitak.gov.tr/chem/issues/kim-99-23-2/kim-2...
Other than that, you are being awfully vague. O. Chem being what it is, there are so many special cases that general rules often don't apply. Pick
the right carboxylic acid, and you could reduce it to an alcohol via a catalyst, sunlight, and a very mild reducing agent, like water.
[Edited on 17-9-2008 by zed]
[Edited on 17-9-2008 by zed]
|
|