Furch
Hazard to Others
Posts: 130
Registered: 8-10-2006
Member Is Offline
Mood: No Mood
|
|
Drying solvents with Al.
An idea occured when I read the current Al/Hg reduction thread.
Since pure aluminium reacts readily with water to form Al(OH)3 and H2, would it not be possible to use amalgamated aluminium to remove a whole lot (or
all) of the water from chemically "inert" solvents prior to moisture sensitive reactions? Solvents such as THF, Et2O... But also to remove water from
alcohols, such as ethanol.
Al + EtOH -/-> Al(OEt)3 + H2
Al(OEt)3 + H2O -/-> Al(OH)3 + EtOH
This method is used to dry ethanol, only magnesium is employed instead (Vogel's). Why not aluminium? It's a hell of a lot cheaper than both magnesium
turnings and sodium wire.
Of course, amalgamating the aluminium with mercury salts is potentially unpleasant, but still.
What say ye?
\"Those who say do not know, those who know do not say.\" -Lao Tzu
|
|
|
Nicodem
Super Moderator
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
It mostly depends on how effective it is in drying THF or other inert solvents. I doubt it can approach the effectiveness of a sodium wire and it
certainly pales in comparison to the benzophenone ketyl radical drying method generally used. The dissolution of aluminium, in my experience, stops as
soon as it gets covered with too much alumina slurry. You would need a terribly effective mechanical stirring in order to remove the hydrated alumina
from the surface of aluminum amalgam and still it would take days for it to react with most water. On the other hand you might be able to dry it
enough for a Grignard or some other such less demanding reaction. It is in the practical aspects and the apparatus required that I see problems.
Edit: I only now realize you are talking about drying ethanol. I don't think that would work well. Al(OH)3 might be soluble in ethanol by forming some
kind of equilibriums among possible complexes. For example, you could end up with partially hydrolyzed species like Al(OEt)2OH which are likely to get
solvated by ethanol instead of precipitating hydrated alumina. This would cause the same problem due to which sodium can not be used for drying
ethanol (see Vogel for the explanation).
[Edited on 2/10/2007 by Nicodem]
|
|
|
Furch
Hazard to Others
Posts: 130
Registered: 8-10-2006
Member Is Offline
Mood: No Mood
|
|
I hear you Nicodem. Slurry'ing would be a real problem...
I guess drying the azeotropic mixture of THF-water with only Al would be pretty useless... But as a final touch it could work. I.e. after drying with
KOH, which removes quite a bit of water in my experience. Then only a smaller amount of Al needs to be used, and hence intense magnetic stirring could
work.
After all, one mole of Al removes three water - for drying one litre of KOH dried THF, I'd say it would be enough with a few grams of Al and a couple
of days of reflux to remove the last accessable water.
I visit my lab about once every two weeks or so, so time is on my side.
I will give it a go someday ahead and report back! I'll test the THF water content with sodium metal when done.
Unfortunately I don't have any benzophenone lying around... 
I just think it's a shame everytime I need to use sodium metal to dry my solvents, as I'd like to use it for other things.
What is your opinion on using activated magnesium as drying agent for ethers?
Thanks for the quick reply! Any further pointers are welcome, of course.
[Edited on 2-10-2007 by Furch]
\"Those who say do not know, those who know do not say.\" -Lao Tzu
|
|
|
Panache
International Hazard
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
i was fairly sure of reading in an older vogel (3rd i think) of drying 96% ethanol by distilling it over an al amalgam after first refluxing it over
the amalgum. a decent reflux serves as an adequate mixer in this system (i have used this method). However i never did assay the ethanol i dried but
it worked fine in the applications i used it for and wet ethanol wouldn't have, so this was enough evidence for me.
The setup is predictable, distillation vessel->column->stil head->condensor->collection vessel->drying tube. Replace the collection
vessel after some 20ml is collected as this will have some water from the residual on the setup, take the replacement one straight from the oven at
150C and fit it while hot.
voila
come to think of it using al powder, added slowly would work much more quickly than foil or fine wire but requires more care, but i'm not game to try,
besides i have a furnace now and quicklime is the way for me.
anyway thats what i know
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Remember that aluminium reacts with alcohols to form Al(OR)3. The low solubility of Al(OH)3 will drive the equilibrium 3ROH + Al(OH)3 <=> 3
H2O + Al(OR)3 to the left, but once most of the water has teacted the alkoxide formed will quickly spread throughout the liquid, quickly zapping
remaining water. And excess alkoxide is not going to distill over as it is rather non-volatile.
|
|
|
kmno4
International Hazard
Posts: 1497
Registered: 1-6-2005
Location: Silly, stupid country
Member Is Offline
Mood: No Mood
|
|
Al alkoxides are rather volatile.
It should be clearly described what amount of water we want to remove from solvent (and what solvent). Procedures are different in the case of <1%
and 5% or 10%. Drying ~95% ethanol with Al(Hg) is really big pain in the ass  .
You will get a kind of cake with a lot of C2H5OH strongly adsorbed on Al2O3 hydrates. Even destillation this mixture is painful because of overheating
and slow desorbing of etanol from Al2O3xH2O. Concentration of H2O is relatively high in 95% EtOH (count it in mol/mol)
If you want to remove small (<1%) amounts of H2O from ethanol, you can use Al(Hg) with no problems. For ethers, Na is very good.
The only cheap procedure ( I know) of drying ~90% sovents (rather solutions) is using CaC2. I wrote a post abot it and do not want to write the same
here. My denurated EtOH dried with carbide react easily with Mg (+I2), so it is dry enough. The fact that it has not special pleasant odour, has no
matter for me.
Large amounts of water can be removed from THF or dioxane in the same way. It is also a test for water content (brown-red CaC2 -> white Ca(OH)2 ).
BTW:
Using benzophenone in EtOH solutions is (of cource) useless.
Слава Україні !
Героям слава !
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Al(OEt)3 - BP 320 C, 210 C @ 10 mmHg, 180 C @ 4 mmHg
mp 154 to 159 C
The alkyls are more volatile, Al(Et)3 has a bp of 186 C
MgSO4 will work to rough dry EtOH, Al is indeed a finishing agent. Don't distill from the main reaction mix, filter and add a bit of fresh Al-Hg,
reflux, distill - not to dryness.
Calcium carbide does work well, too. It has become difficult to get in some places.
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
| Quote: | Originally posted by Nicodem
...it certainly pales in comparison to the benzophenone ketyl radical drying method generally used. |
How is this done exactly? I need to use this soon..ph-Li involved..
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
|
contrived
Hazard to Self
Posts: 56
Registered: 9-3-2007
Location: Washington State
Member Is Offline
Mood: skeptical
|
|
I can't find it either; I tried Perrin & Armego and Vogel's 3rd.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
http://www.chemistry.msu.edu/Safety/safety_sop_01.asp
|
|
|
YT2095
International Hazard
Posts: 1091
Registered: 31-5-2003
Location: Just left of Europe and down a bit.
Member Is Offline
Mood: within Nominal Parameters
|
|
| Quote: | Originally posted by kmno4
Besides - have you ever tried drying EtOH with MgSO4 ? Iam sure you have not, because it just does not work
|
I have actually tried this myself and I have to agree, the results were Very poor
I`m not going to say it Doesn`t work, it just didn`t work for ME.
\"In a world full of wonders mankind has managed to invent boredom\" - Death
Twinkies don\'t have a shelf life. They have a half-life! -Caine (a friend of mine)
|
|
|
kmno4
International Hazard
Posts: 1497
Registered: 1-6-2005
Location: Silly, stupid country
Member Is Offline
Mood: No Mood
|
|
So let us say that we both (and propably thousands others) have done this wrongly....
Let us wait untill someone will succeeed (~95% -> ~99% with MgSO4). In the meantime I will watch my growing beard.... becoming white....
Слава Україні !
Героям слава !
|
|
|
kmno4
International Hazard
Posts: 1497
Registered: 1-6-2005
Location: Silly, stupid country
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by not_important
Al(OEt)3 - BP 320 C, 210 C @ 10 mmHg, 180 C @ 4 mmHg
mp 154 to 159 C
The alkyls are more volatile, Al(Et)3 has a bp of 186 C
MgSO4 will work to rough dry EtOH, Al is indeed a finishing agent. Don't distill from the main reaction mix, filter and add a bit of fresh Al-Hg,
reflux, distill - not to dryness.
Calcium carbide does work well, too. It has become difficult to get in some places. |
BP 320 C means what it means. Compare it to NaCl, CaC2, NaOH, K2SO4... or any ionic/polymeric compound. I did not say that such alkoxides boil at 50 C
or so. Al alkoxides are rather volatile compounds and can be easyli purificated by (vacuum) distillation.
Besides - have you ever tried drying EtOH with MgSO4 ? Iam sure you have not, because it just does not work
BTW:
Interesting article (free) about benzohpenone salts of Na can be found here:
http://www.rsc.org/publishing/journals/DT/article.asp?doi=b5...
It it worth to dowload "Electronic supplementary information" in CIF format and open it in Mercury (free) program, to see nice 3D (+a few options)
structures of solvated Na salts.
**** this is my second post in this thread (a little mistake with deleting..)
Слава Україні !
Героям слава !
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
solvent stills as related to thread
"To keep stills dry and oxygen free, they are connected to an inert gas source, and fitted with a bubbler to vent excess pressure."
Are we ageed that a baloon works as well and has the added advantage of maintaining positive pressure on the system?
and:
do I have to put benxophenone and Na in my ultrasound cleaner to make the ketyl? or do I reflux the two? how long? until the color is deep blue?
ie, how do I make the stuff? nevr done it .. used Na in the past or CaO for alcohol...
[Edited on 19-12-2007 by chemrox]
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
|
cbfull
Harmless
Posts: 33
Registered: 24-6-2006
Location: OH
Member Is Offline
Mood: No Mood
|
|
What about passing the vapor phase over a column of silica gel, or even drierite? Silica gel can have bad reactions to liquids, but a vapor should be
fine.
Has this been done before? Insight?
|
|
|
Furch
Hazard to Others
Posts: 130
Registered: 8-10-2006
Member Is Offline
Mood: No Mood
|
|
The point was to use Al because it's dirt cheap and ridiculously available. Also, if it works, it will probably remove nearly _all_ of the water.
MgSO4 is a really crappy drying agent when trying to make something close to anhydrous.
I will give the Al method a try sometime, and report back to you my findings.
- Furch
\"Those who say do not know, those who know do not say.\" -Lao Tzu
|
|
|
dangator
Harmless
Posts: 8
Registered: 22-1-2008
Member Is Offline
Mood: No Mood
|
|
The use of alumina columns for drying solvents is widespread, the original credit goes to Grubbs for phasing out solvent stills. Maybe three phase
drying using something stupid (MgSO4), distillation, followed by running though an alumina column would work wonders. The alumina can likely be
reactivated with excessive heating. Even easier is just using molecular sieves of the appropriate size--they're incredible dehydrating agents that
receive less credit than they deserve. Of course you'll want to do one of these to quantitate what's happening:
http://en.wikipedia.org/wiki/Karl_Fischer_titration
|
|
|
Panache
International Hazard
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
buy a air-conditioning drying canister from a refrigeration supplies and run your solvent through it. They are filled with mol sieves and if you
choose the right ones (read the catalogue) they are idiot-proof, well almost.
They are designed to remove water from refrigerants and are usually fitted in-line just after the compressor so the refrigerant is a liquid as it
passes through them.
One the size of a can of soft drink generally mops about 20mL of water. ensure you don't break the wax seal until you use it though as it will grab
water from the air. I haven't tried opening one before to regenerate it.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
