bilcksneatff
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 54
Registered: 11-11-2007
Location: Maryland, USA
Member Is Offline
Mood: Sulfuric
|
|
neon transformer
Does anybody know how to make a neon transformer? If not, where I can get one?
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
I know how to make one, but I don't know why one would want to.
Try phoning your local neon sign supplier. Additionally, UTFSE. Finding NSTs has been hammered to death by the Tesla coil crowd, information is
abundant.
Tim
[Edited on 11-19-2007 by 12AX7]
|
|
bilcksneatff
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 54
Registered: 11-11-2007
Location: Maryland, USA
Member Is Offline
Mood: Sulfuric
|
|
I was looking for a way to make NO2 gas. I would use the NO2 to make nitric and possibly sulfuric acids.
Would a Van de Graff generator work for this? I have a partially finished generator in my garage.
[Edited on 19-11-2007 by bilcksneatff]
|
|
Xenoid
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
Quote: | Originally posted by bilcksneatff
Would a Van de Graff generator work for this? I have a partially finished generator in my garage.[Edited on 19-11-2007 by bilcksneatff]
|
Not unless it's a bloody big one!
A homemade VDG might produce 500,000 volts at 10uA that's only 5 watts! Whilst they can produce spectacularly long sparks a VDG can only maintain
relatively low currents.
If you can't locate a NST your best bet might be an automobile ignition coil. There are plenty of circuits on the web for driving these. Driving two
of the old style coils wired in antiparallel can give a fairly "grunty" performance comparable to a NST.
Regards, Xenoid
|
|
bilcksneatff
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 54
Registered: 11-11-2007
Location: Maryland, USA
Member Is Offline
Mood: Sulfuric
|
|
Thanks, Xenoid!
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
You want a fat, hot arc, not a thin, wussy spark. Amps, not volts. You're going the wrong way. Try a carbon arc torch.
Tim
|
|
dann2
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
Hello,
The transformers in microwave ovens put out 1500volts or there abouts. A few in series would up the voltage.
Theses things put out quite a few amps, are current limited (at a amp or so I think) AND ARE (FUk?*@$) LETHAL. [Probable not supposed to use that
language but it is just to get your attention.] They have killed people who know alot more about electrics that most.
Dann2
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1314
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Microwave oven transformers (MOT) are not current limited like a neon transformer (NST). So as soon as you strike an arc, you will try to pull the
whole national grid through your wall socket (an exageration, but you get the idea). To use an MOT you will need an impedance (L or C) in series with
the primary.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
No, they are. Just not all that well.
NSTs have the same magnetic shunts in them that MOTs do, but MOT shunts are narrower --> less current limiting. The magnetron doesn't need too
much current limiting, but an arc sure as hell does.
What you really want is an inductor, in series with the MOT primary, of about 20 milihenries, 10A capacity. This will be about the same size as an
MOT, but built differently. You could also use an 8 ohm resistor (approximately a space heater's heating element), but then you're wasting power in
the element that could be ionizing air instead. An inductance is lossless.
Tim
|
|
dann2
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
Hello,
It is not a good idea to connect a microwave transformer to the mains directly without a load. The designer/manufacturer of the oven always knew there
would be a load on the transformer (the Magnetron) and therefor could skimp on input windings. If you connect two (or three perhaps) of theses
transformers together you may be OK. The primarys need to be connected in series, the secondarys go in series too.
This is dangerous stuff as the currents available are high.
Dann2
|
|
497
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 778
Registered: 6-10-2007
Member Is Offline
Mood: HSbF6
|
|
actually from what i've read a high voltage low current is best. a high current arc puts a lot of energy into the electrodes and radiant heat which is
wasted. the higher voltage makes an arc with more concentrated heat and a sharper gradient (very important to minimize decomposition of the NO. they
tested all this back at the turn of the century. best yield i've heard of industrially was 950 kg HNO3 per kilowatt year (110 g per kwh.) on the other
hand an MOT might be the best option simply because they're cheap and easy to get. a big NST would be better i think but i've heard they're pretty
expensive.
|
|
bilcksneatff
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 54
Registered: 11-11-2007
Location: Maryland, USA
Member Is Offline
Mood: Sulfuric
|
|
There was a book somewhere that had plans for an "anti-gravity levitator." It had a complete schematic for a high-voltage transformer. I can't
remember the output voltage though, probably was over 1kV.
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
Quote: | Originally posted by dann2
Hello,
It is not a good idea to connect a microwave transformer to the mains directly without a load. |
Actually, this is not true for any transformer design I am aware of.
Switching power supplies often need a minimum load, on the other hand. Very different animal.
Quote: | Originally posted by 497
actually from what i've read a high voltage low current is best. |
What I heard is, thin high voltage sparks, especially those giving mostly blue colors, are a result of oxygen breakdown and ultraviolet radiation,
therefore giving plenty of ozone -- which smells like NO2, but most certainly isn't.
N2 + O2 <---> 2NO is an equilibrium and goes a bit to the right at high temperatures (even mere flame temperatures; ionization needn't enter
into things here). Indeed, a high refractory resistive element alone might be used to heat air to approximately 2000C or so, with long life -- no
sputtering to worry about. I don't know if you'd get as much yield as with an ionizing source.
Ya know, pressure is also something to consider. Isn't Le Chatelier's in favor of NO2, after all? Pump that sucker up to 10 atm or more. The arc
needs more voltage then (now you have an excuse for an MOT or more evil things still), or a solid heating element could be used. Would also be simple
to absorb in water, which could also be under pressure. In fact, you could use a bubbler pump inside the reaction vessel to circulate the pressurized
air between absorbtion and reaction, and a source of compressed air supplies fresh air. A blowoff would of course be necessary to release excess
nitrogen, argon and other unnecessary gasses.
Tim
[Edited on 11-20-2007 by 12AX7]
|
|
Tacho
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 582
Registered: 5-12-2003
Member Is Offline
Mood: No Mood
|
|
Recently I have built an "arc generator" putting the two carbon rods in series with the primary winding of a big transformer (scrap) and then removing
the core's steel plates, a few at a time, until the arc was sustained with the right intensity.
In other words: I started with a big ballast and made it less inductive in steps until it suited my needs.
Beware that the primary winding must be made of thick wire to prevent overheating, and I have 127V in my mains. At 220 or 240V you are taking much
higher risks.
|
|
dann2
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
Quote: | Originally posted by Tacho
Recently I have built an "arc generator" putting the two carbon rods in series with the primary winding of a big transformer (scrap) and then removing
the core's steel plates, a few at a time, until the arc was sustained with the right intensity.
In other words: I started with a big ballast and made it less inductive in steps until it suited my needs.
Beware that the primary winding must be made of thick wire to prevent overheating, and I have 127V in my mains. At 220 or 240V you are taking much
higher risks. |
Hello,
Do you mean, putting the carbons in series with the secondary?
Dann2
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
No, he is in fact using the transformer's primary winding as an inductor. An effective method, but wastes a lot of VA as well.
Tim
|
|
Tacho
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 582
Registered: 5-12-2003
Member Is Offline
Mood: No Mood
|
|
Quote: | Originally posted by 12AX7
No, he is in fact using the transformer's primary winding as an inductor. An effective method, but wastes a lot of VA as well.
Tim |
Exactly.
Check this forum for "arc furnaces" and you will find a couple of links to DIY arc furnaces that use an inductor as current limiting device to what
would otherwise be a short-circuit. I used a transformer simply because it was the only heavy-duty inductor I had around and I was too lazy to wind
one myself. I used the primary because it had thicker wire, that's all.
|
|
Xenoid
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
Dann2, if you feel like suicide because your LDO anodes keep falling apart, try making this from the 1930's......![:o](./images/smilies/shocked.gif)
http://blog.modernmechanix.com/2007/03/19/experimental-arc-f...
Regards, Xenoid
|
|
Tacho
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 582
Registered: 5-12-2003
Member Is Offline
Mood: No Mood
|
|
Notice the fellow in the picture uses a smoking, bowtie, no gloves, and looks directly to the electric arc without googles.
Oh, and what would happen if that crucible full of white-hot molten metal tips over and splashes over his lap?
Lovely picture indeed.
[Edited on 22-11-2007 by Tacho]
|
|
Xenoid
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
Yeah!... I love that image!
The guy looks like a cross between Howard Hughes and a stage magician!
And no goggles, even though the article warns that they should be worn!
Regards, Xenoid
|
|
JohnWW
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2849
Registered: 27-7-2004
Location: New Zealand
Member Is Offline
Mood: No Mood
|
|
Anti-gravity levitator
Quote: | Originally posted by bilcksneatff
There was a book somewhere that had plans for an "anti-gravity levitator." It had a complete schematic for a high-voltage transformer. I can't
remember the output voltage though, probably was over 1kV. |
For that item, try:
http://www.techkits.com/
http://www.makezine.com/extras/31.html
http://www.greatdreams.com/scalar.htm
http://antigravity.altervista.org/levitus.html
Also look up "Otis T. Carr" on Google. He based his invention in the 1950s on Tesla's work.
[Edited on 24-11-07 by JohnWW]
|
|
dann2
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
Hello,
From 'Coil design and construction manual' by B.B. Babani
Enjoy!!!!!!!!!
You may need to go to WWW.LIZARDTECH.COM for to get a reader for this type of doc.
Dabb2
Attachment: chokes.djvu (47kB) This file has been downloaded 615 times
|
|
Texium
|
Thread Moved 19-11-2023 at 12:12 |