alking
Hazard to Others
Posts: 252
Registered: 11-3-2016
Member Is Offline
Mood: No Mood
|
|
Does washing ether with a hydroxide solution make it safe enough to distill to dryness?
Wouldn't any peroxides be washed away? What if you were to just add some water and distill it from that, would the peroxides safely dissolve into the
water? These seem like the most simple methods of recovery to me, however I don't see people recommending either so I wonder if I'm missing
something.
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
I'm not sure, but you could always just test it for peroxides?
|
|
|
alking
Hazard to Others
Posts: 252
Registered: 11-3-2016
Member Is Offline
Mood: No Mood
|
|
I don't have any KI on hand to do so. I have some Alumina that I could use but I'd rather not waste it if I don't have to and especially for the long
run this would be good information to know if I plan to continue using Et2O.
|
|
|
arkoma
Redneck Overlord
Posts: 1761
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
KI is cheap and multi useful
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
|
zed
International Hazard
Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Not distilling to dryness, is kind of a standard.
Peroxide formation doesn't start and end, with ethers.
Plenty of other materials, are prone to this problem.
Then, there might be things, other than peroxides, left in your dregs, that shouldn't be totally dried out or overheated.
I'm not the resident expert, perhaps someone present, has better insight?
|
|
|
aga
Forum Drunkard
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
Why, exactly, do you need to distill to dryness ?
Makes no sense.
|
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
Adding OH-(aq) hoping to remove peroxides is just adding extra labour work. Youll have to add another unnecessary step of removing aq layer with sep
funnel to ur experiment. Id rather simply leave a little bit of ether in flask just like every1 else. Thats simpler. Also u shouldn't boil anything to
dryness anyways no matter what experiment ur doing (unless the aim is rly finding out whats left after boiling to dryness)
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
The classic treatment to remove peroxides is a wash with FeSO4 solution. However, I would still avoid distilling all the way to dryness.
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
If you are redistilling ether then it makes sense to distil off as much as you can. That means distilling it down to nothing.
It's obviously best to remove any peroxides before doing this.
If you are unable to remove all the peroxides there's still a way round it.
Add something involatile to the ether- perhaps engine oil and then distil.
Any peroxides left behind will be diluted in the oil so, if they decompose, it won't matter much.
|
|
|
alking
Hazard to Others
Posts: 252
Registered: 11-3-2016
Member Is Offline
Mood: No Mood
|
|
I didn't realize this thread had more replies. I never intended to distill to dryness, I was just hoping to safely recover all or most of the ether
without worry of peroxides. If I recovered all of it I'd add some water to prevent boiling it dry for instance. I did consider adding something I know
the peroxides would be soluble in such as isopropanol, but then I'd have to deal with any azeotropes and wash it out post distillation. Adding a
higher boiling oil is a good idea though that I hadn't considered. I wish I could find some solubility data for the peroxides, that would answer a lot
of questions.
I did find an actual answer to my hydroxide wash question though and the short answer is that it works but only to a degree, it's not effective enough
to remove all of the peroxides. I will update with the reference for that when I get home, it has all sorts of data about the effectiveness of various
methods. The most effective/easy seemed to be washing it with sodium bisulphate.
|
|
|
alking
Hazard to Others
Posts: 252
Registered: 11-3-2016
Member Is Offline
Mood: No Mood
|
|
Here's the reference I mentioned yesterday, it actually was posted here, I didn't realize that.
http://www.sciencemadness.org/talk/files.php?pid=153704&...
I can't copy and paste from the pdf but on page 5 (or 41 by the page nums) it lists a chart showing various concentrations of NaOH sol that were shook
with ether for 15 minutes and the amount of peroxides measured before and after. It does mention and imply that "steam distilling over a hydroxide
solution" as being safe, but it doesn't go into any details than the brief mention so I question it. I don't think that even qualifies as an actual
steam distillation seeing as there wouldn't be any steam or vapor phase interaction with the water.
I just realized that I did actually ask if it would be safe to distill to dryness, but I did not intend to actually do so, I just wanted to know if it
was safe because if it is then I wouldn't have anything to worry about when approaching it. I do not really see a problem doing so with such low
boiling solvents however (contaminants aside), if you do it on a water bath or an otherwise low/controlled temperature nothing significant would be
distilled with it or cause any damage to the glassware.
[Edited on 17-6-2018 by alking]
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Quote: Originally posted by alking  | I do not really see a problem doing so with such low boiling solvents however (contaminants aside), if you do it on a water bath or an otherwise
low/controlled temperature nothing significant would be distilled with it or cause any damage to the glassware.
|
I do not understand what you are trying to say. Peroxides explode on low temperatures just fine.
|
|
|
alking
Hazard to Others
Posts: 252
Registered: 11-3-2016
Member Is Offline
Mood: No Mood
|
|
No, that's what I meant by "contaminants aside." I was just speaking of dry distilling in general as people were saying you should never do so. It's a
good rule of thumb but there are exceptions. If you have a low boiling solvent without harmful contaminants and good temperature control there
shouldn't be any reason you could not safely and effectively distill it dry.
|
|
|
Chemi Pharma
Hazard to Others
Posts: 349
Registered: 5-5-2016
Location: Latin America
Member Is Offline
Mood: Quarantined
|
|
Trying to remove organic peroxides from diethyl ether or THF with alkaline hydroxides is a bad idea. Many accidents have occurred following this
procedure. Orgsyn.com have a few procedures alerting to it.
You'd better use FeSO4 (5 grs in 20 ml of water for each liter of ether or THF). This will destroy all of your peroxides, although it was an
exothermic reaction and must be conducted with caution if your ether or THF are very, very old.
Then, separate the layers, dry with anhydrous magnesium or sodium sulfate and distill all the organic layer until dried with no fear at all.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
