monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Pump for recirculating aspirator?
I'm looking to build a recirculating aspirator for vacuum filtration and vacuum distillation. My goal is 100mm Hg or under, which seems reasonable
given the spec sheets of the Nalgene aspirator I want to use. I've done some research and came up with the following:
A submersible pump has far too much flow rate, which would dump heat into the water.
A fountain pump has reasonable flow rate but terrible pressure.
An RV water pump was seen in a NurdRage video, but many comments complained that typical performance was poor. There are also concerns about the
longevity of the motor, since they are meant for intermittent use and not 100% duty cycle.
A used Procon pump, but 125gph and 175psi is way overkill and might blow up the aspirator.
A used 3/4 hp pool or spa pump, but I can't seem to find pressure ratings for most of these so I'm not sure.
A generic transfer pump/jet pump/utility pump like any of these, but I'm not sure how they would handle a 100% duty cycle for hours:
https://www.harborfreight.com/120-volt-portable-utility-pump... (1500 gph, 55 psi)
https://www.northerntool.com/shop/tools/product_200672183_20... (580 gph, 50 psi)
Any suggestions or input? I'm looking to keep the cost of the pump at around $100. I'm guessing 100 gph at 50psi are my target outputs, but I'm not
exactly sure what that corresponds to at the typical max flow rate @ 0 psi and min flow rate @ max psi ratings that datasheets give? I have considered
buying a cheap Harbor Freight vacuum pump but I don't need that much vacuum and using a needle valve to reduce vacuum will (apparently) cause the pump
to puke oil all over. It seems like building a recirculating aspirator is the best route, if I can just find a reasonable pump.
[Edited on 6-3-2018 by monolithic]
|
|
|
Vosoryx
Hazard to Others
Posts: 282
Registered: 18-6-2017
Location: British Columbia, Canada
Member Is Offline
Mood: Serial Apple Enjoyer
|
|
This might help:
http://www.sciencemadness.org/talk/viewthread.php?tid=78427
It works fine for most everything i've thrown at it thus far.
100 psi 5 lpm for the water pump.
"Open your mind son, before someone opens it for you." - Dr. Walter Bishop
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Do you happen to know much vacuum it can pull?
|
|
|
Vosoryx
Hazard to Others
Posts: 282
Registered: 18-6-2017
Location: British Columbia, Canada
Member Is Offline
Mood: Serial Apple Enjoyer
|
|
Actually, not off the top of my head.
I tested it by boiling water with a thermometer in it, but that number is currently written in the back of my lab journal. Usually not a problem, but
i'm away from home right now. Sorry.
Other amateurs have had a lot of success with aspirators though. I seem to remember nurdrage used the same specs on the water pump... I think he got
water to boil ~20 C.
"Open your mind son, before someone opens it for you." - Dr. Walter Bishop
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Vosoryx  | Actually, not off the top of my head.
I tested it by boiling water with a thermometer in it, but that number is currently written in the back of my lab journal. Usually not a problem, but
i'm away from home right now. Sorry.
Other amateurs have had a lot of success with aspirators though. I seem to remember nurdrage used the same specs on the water pump... I think he got
water to boil ~20 C. |
Yes, I saw the one he built in his video performed amazingly. The replies to his videos said his results weren't typical. Even in your thread, the
other poster was complaining that his vacuum was weak. If you have the time, I'm curious to see what the boiling point of water under vacuum was for
your setup. 
|
|
|
Vosoryx
Hazard to Others
Posts: 282
Registered: 18-6-2017
Location: British Columbia, Canada
Member Is Offline
Mood: Serial Apple Enjoyer
|
|
Yeah, i'll let you know once I get back to my lab next week-ish.
"Open your mind son, before someone opens it for you." - Dr. Walter Bishop
|
|
|
FireLion3
Hazard to Others
Posts: 218
Registered: 11-1-2014
Member Is Offline
Mood: No Mood
|
|
125gph, did you mean gpm? I tried to use a 3gpm / 180 gph diaphragm pump to recirculate water for my aspirator and it was completely ineffective,
whereas the aspirator worked fine on the faucet. I tried this using a different pump as well with a slightly higher flow rate. With both pumps, the
vacuum that gets pulled is so insignificant that it's basically useless.
At the time I speculated that the lack of vacuum was caused by the pulsing rhythm of the pumps, as it was the only clear difference I could notice
between a faucet stream and the stream from the pump.
If you only need around vacuum aspirator level vacuum, you could look into buying a used diaphragm pump on eBay. They're often very cheap and durable,
and do not require changing oil (which would often become contaminated with solvents from vacuum filtration)
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by FireLion3 |
125gph, did you mean gpm? I tried to use a 3gpm / 180 gph diaphragm pump to recirculate water for my aspirator and it was completely ineffective,
whereas the aspirator worked fine on the faucet. I tried this using a different pump as well with a slightly higher flow rate. With both pumps, the
vacuum that gets pulled is so insignificant that it's basically useless.
At the time I speculated that the lack of vacuum was caused by the pulsing rhythm of the pumps, as it was the only clear difference I could notice
between a faucet stream and the stream from the pump.
If you only need around vacuum aspirator level vacuum, you could look into buying a used diaphragm pump on eBay. They're often very cheap and durable,
and do not require changing oil (which would often become contaminated with solvents from vacuum filtration) |
No, 125gph. If it was 125gpm it would be super overkill. When you say you
recommend buying a used diaphragm pump, you're referring to a vacuum pump?
|
|
|
Sulaiman
International Hazard
Posts: 3697
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
If just for vacuum filtration I can recommend this https://www.ebay.co.uk/itm/DC-12V-24V-80Kpa-Micro-Piston-Vac...
you would also need 12 Vdc at up to 2 Adc - a dedicated power supply, PC PSU, car battery etc.
Water boils at 65oC or less with this pump and I ran it for days continuously with no problems.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
